Dynamic Shift Registers - Bitsavers - Trailing-Edge

(.)0')....ooJ:Z........0')....ooJ:Z.(.)oq-....ooJ:Z........oq-....ooJ:Zabsolute maximum ratingsVee Supply Voltage 7.0VVminus Supply Voltage -30VVplus Supply Voltage +30VVplusNminus Voltage Differential40VLogic Input Voltage 5.5VStorage Temperature Range_65°C to +150°COperating Temperature Range NH0014, NHOO19 -55°C to +125°CNH0014C, NHOO19C DoC to +70°CLead Temperature (Soldering, 10 sec) 300°Celectrical ch aracteristics (Note 1)PARAMETER CONDITIONS MINLogical "1" Input Voltage Vee = 4.5V 2.0Logical "0" Input Voltage Vee = 4.5VLogical "1" Input Current Vee = 5.5V V 1N = 2.4VLogical "1" Input Current Vee = 5.5V V 1N = 5.5VTYP(Note 3)Logical "0" Input Current Vee = 5.5V V 1N = O.4V 0.2Power Supply Current Logical" 1" input Vee = 5.5V V 1N = 4.5V 0.85NH0019, NH0019C-each gate (Note 2)Power Supply Current Logical "0" input Vee = 5.5V V 1N = OV 0.22NH0019, NH0019C-each gate (Note 2)Power Supply Current Logical" 1" input Vee = 5.5V V 1N = 4.5V 0.85NH0014, NH0014C (Note 2)Power Supply Current Logical "0" input Vee = 5.5V V 1N = OV 1.5NH0014, NH0014C (Note 2)Analog Switch ON Resistance V 1N (Analog) = +10V 75(each gate) V 1N (Analog) = -10V 200Analog Switch OFF ResistancelOllAnalog Switch Input Leakage Current V 1N = -10V T A = 25°C 0.05NH0014C, NHOO19C (Note 4) T A = 70°C 4NH0014, NHOO19 V 1N = -10V TA = 25°C 25(Note 4) TA = 125°C 25Analog Switch Output Leakage Current VOUT = -10V TA = 25°C 0.1NH0014C, NHOO19C (Note 4) TA = 70°C 30NH0014, NHOO19 VOUT=-10V TA = 25°C 40(Note 4) T A = 125°C 40Analog Input (Drain) Capacitance 1 MHz @ Zero Bias 8Output Source Capacitance 1 MHz @ Zero Bias 11Output Transition Time for TA = 25°C 200Logical "0" InputOutput Transition Time for TA = 25°CLogical "1" Input NH0019, NHOO19C 100NH0014, NHOO14C 250MAXUNITSV0.8 V5 J..LA1 mA0.4 mA1.6 mA0.41 mA1.6 mA3.0 mA200 Q600 QQ10 nA50 nA200 pA200 nA10 nA100 nA400 pA400 nA10 pF13 pFnsnsnsNote 1: Min/max limits apply across the guaranteed temperature range of -55°C to +125°C forNH0014, NH0019 and oOe to 70°C for NH0014C, NH0019C. Vminus = -20V, Vpl us = +10V and ananalog test current of 1 mA unless otherwise specified.Note 2: Current measured is drawn from Vce supply.Note 3: All typical values are measured at TA = 25°C with VCC = 5.0V. Vpl us = +1 OV, Vminus = -22Vunless otherwise noted.Note 4: All analog switch pins except measurement pin are tied to V plus.164