TracVision DIRECTV Mobile Receiver/Controller User's Guide
TracVision DIRECTV Mobile Receiver/Controller User's Guide TracVision DIRECTV Mobile Receiver/Controller User's Guide
Getting Started2-1 Turning On the AntennaTo quickly start watching satellite TV using theTracVision system, follow the simple steps below.1. Apply power to the mobile receiver/controller.The Receiver status light should turn green.2. Turn on your TV and select the satellite input (notthe VCR input).3. Wait 30-60 seconds for the antenna to acquire thesatellite signal. The TV will show the following:4. If Message 1 does notappear after 30 seconds,PWRpress the remote control’sDVD VCR AUX TV SATSAT button. Then pressthe remote’s PWR button.GUIDEMENU TURBO FAVThe receiver beeps twice,the Antenna status light begins to flash green,and the Voltage status light should be lit green.Status LightsNELINE GUIDMessage 1If your satellite dish is ready for DIRECTV ®service, please wait until yourAdvanced Program Guide is prepared.InstallationSignal not available...For details about the statuslights, see Section 10-4,“System Status Lights” onpage 10.10.54-0376Message 2If your satellite dish is ready for DIRECTV ®service, please wait until yourAdvanced Program Guide is prepared.InstallationAcquiring guide data...If the receiver’s Voltage statuslight is off, press the powerswitch on the front of thereceiver to turn on thereceiver.Power Switch2.3
DIRECTV Mobile Receiver/Controller User’s Guide5. If Message 2 does not appear after Message 1,ensure that the antenna has a clear view of thesatellite. The antenna requires an unobstructedview of the sky to receive satellite TV signals.*Once the antenna locks onto the satellite, thereceiver starts downloading the program guide.This may take up to 60 seconds.Program GuideOnce the program guide has loaded, you can startenjoying satellite TV!*** For details about satellite reception requirements, see page 1.5.** If you can only view the DIRECTV Preview Channel, your receiverhas not been activated. See page v.Why Does the Receiver Beep?The receiver beeps to indicate thestatus of the antenna.2 beeps = Antenna is powering on1 beep = Antenna is powering off2.454-0208
- Page 1 and 2: DIRECTV ® MobileReceiver/Controlle
- Page 3: DIRECTV Mobile Receiver/Controller
- Page 6 and 7: Technical SupportReceiver/Controlle
- Page 8 and 9: Table of Contents1 Introduction . .
- Page 10 and 11: Introduction1 IntroductionContentsT
- Page 12 and 13: RECREWINPUTSTOPPLAY0FPROGVOLVIDEOPR
- Page 14 and 15: DIRECTV Mobile Receiver/Controller
- Page 18 and 19: Getting Started2-2 Changing Channel
- Page 20 and 21: Using the Remote ControlTracVision
- Page 24 and 25: SEARCHPREVCHUsing the Remote Contro
- Page 26 and 27: Using the Remote Control3-2 Program
- Page 28 and 29: Using the Remote Control8. At the s
- Page 30 and 31: Overview of Onscreen Displays4-1 Th
- Page 32 and 33: Overview of Onscreen Displays4-3 Th
- Page 34 and 35: Overview of Onscreen DisplaysMain M
- Page 36 and 37: Overview of Onscreen DisplaysMain M
- Page 38 and 39: Using Program Guides5-1 Program Gui
- Page 40 and 41: Using Program Guides5-2 Using the P
- Page 42 and 43: Using Program Guides5-4 Using Turbo
- Page 44 and 45: Using Program GuidesRenaming TurboT
- Page 46 and 47: Using Program GuidesFiltersPress SE
- Page 48 and 49: Setting Favorites and Filters6-1 Us
- Page 50 and 51: Setting Favorites and FiltersRenami
- Page 52 and 53: Setting Favorites and Filters6-2 Fi
- Page 54 and 55: Setting Favorites and Filters6-4 Us
- Page 56 and 57: Setting Favorites and FiltersUsing
- Page 58 and 59: Using Access Controls7-1 Locking &
- Page 60 and 61: Using Access ControlsUnlocking the
- Page 62 and 63: Using Access ControlsThe Max Spendi
- Page 64 and 65: Other Menu Functions8-1 Adjusting A
Getting Started2-1 Turning On the AntennaTo quickly start watching satellite TV using the<strong>TracVision</strong> system, follow the simple steps below.1. Apply power to the mobile receiver/controller.The <strong>Receiver</strong> status light should turn green.2. Turn on your TV and select the satellite input (notthe VCR input).3. Wait 30-60 seconds for the antenna to acquire thesatellite signal. The TV will show the following:4. If Message 1 does notappear after 30 seconds,PWRpress the remote control’sDVD VCR AUX TV SATSAT button. Then pressthe remote’s PWR button.GUIDEMENU TURBO FAVThe receiver beeps twice,the Antenna status light begins to flash green,and the Voltage status light should be lit green.Status LightsNELINE GUIDMessage 1If your satellite dish is ready for <strong>DIRECTV</strong> ®service, please wait until yourAdvanced Program <strong>Guide</strong> is prepared.InstallationSignal not available...For details about the statuslights, see Section 10-4,“System Status Lights” onpage 10.10.54-0376Message 2If your satellite dish is ready for <strong>DIRECTV</strong> ®service, please wait until yourAdvanced Program <strong>Guide</strong> is prepared.InstallationAcquiring guide data...If the receiver’s Voltage statuslight is off, press the powerswitch on the front of thereceiver to turn on thereceiver.Power Switch2.3