GBC TITAN 1264WF/1244WF - Net

More documents

Recommendations

Info

GBC 1264WF/1244WFOperation ManualTips for ACCUSHIELDIMAGETHERMALFILMOPTIONALSEPERATOR BAR1. Load the laminator as illustrated in Fig.21.2. You must have the Separator bar option to accuratelyrun this material. See your Sales Rep for ordering theSeparator Bar.OUTPUT3. Set Top Temp to 265 o F* ( 129* C) and a speedsetting no greater than 4.4. Liner rewind tension will be greater than normaloperating standardKRAFTPAPER5. To prevent some adhesive adhering to the rollers, youmay choose to use a roll of craft paper for a Carrier.OPTIONFig. 21Use the blank space below and blank diagrams toNote your tips and web paths for your Specialapplications.TIPS FOR CUSTOM APPLICATION #1 (Fig. 22)1.2.3.4.Fig. 22CUSTOM WEB PATH #1TIPS FOR CUSTOM APPLICATION #2 (Fig. 23)1.2.3.4.5.CUSTOM WEB PATH #2Fig. 23© 2006 General Binding Corporation Page 34
GBC 1264WF/1244WFOperation ManualSPEED / TEMPERATURE CONTROLThis is only a general reference guide. Different settings may be suitable as the warm up time, lamination time and materialschange.Factors that may affect the speed and temperature parameters;1. Image length2. Image width and ink coverage.3. Ink coverage4. Paper type5. Laminate thickness6. Operating environment7. Condition of the rollers8. Line voltage (effects heaters)9. Using cooling features.You may have to adjust temperature or speed depending on stock finish, thickness *Turn heat off when not in use.THE ART OF LAMINATIONBASIC RULESDo not attempt to laminate abrasive or metal Objects such as staples, paper clips and glitter, as they may damage theheat or pull rollers.Do not force items into the nip area of the heat rollers. An item that is not easily drawn into the laminator by the heatrollers is probably too thick to laminate.Wrinkles may result if an attempt is made to reposition an item once it has been grasped by the heat rollers.Do not stop the laminator before an item has completely exited the pull rollers. Even a momentary stop will cause amark (heat line) on the laminated item.Good, consistent lamination is a result of combining proper heat, tension and dwell time. Dwell time is controlled by the speed ofthe motor and is defined as the amount of time the material to be laminated is compressed between the heat rollers.As a general rule, thicker items and film need to run at slower speeds because they extract more heat from the rollers at a quickerrate. Setting the speed control at slower settings gives the laminator longer dwell time thus allowing proper lamination of thickitems. Thinner items, such as standard copier paper (20 lb. bond) and tissue paper, extract less heat from the rollers and can berun at faster speeds.FILM TENSIONProper film tension, known as brake tension, is the minimum amount required to eliminate wrinkles in the finished item. The filmshould be taut. A properly adjusted roll of film should not require excessive force to turn by hand.Film tension should be enough to introduce a minor amount of drag as the film unrolls. Insufficient tension causes wrinkles,while too much tension causes stretching (necking). Uneven tensions between the top and bottom rolls create curl. Too muchupper tension creates upward curl while too much bottom tension causes downward curl.Adjustment of the pull roller clutch may be necessary if after adjusting unwind and rewind brake tensions do not improve youroutput quality.© 2006 General Binding Corporation Page 35
Page 6 and 7: GBC 1264WF/1244WFOperation ManualPR
Page 10 and 11: GBC 1264WF/1244WFOperation ManualHe
Page 12 and 13: GBC 1264WF/1244WFOperation ManualSe
Page 14 and 15: GBC 1264WF/1244WFOperation Manual©
Page 16 and 17: GBC 1264WF/1244WFKnow your Laminato
Page 18 and 19: GBC 1264WF/1244WFOperation ManualDi
Page 28 and 29: GBC 1264WF/1244WFOperation ManualWe
Page 30 and 31: GBC 1264WF/1244WFOperation ManualMe
Page 32 and 33: GBC 1264WF/1244WFOperation ManualTi
Page 36 and 37: GBC 1264WF/1244WFOperation ManualHe
Page 38 and 39: GBC 1264WF/1244WFOperation ManualTR

GBC TITAN 1264WF/1244WF - Net

Create successful ePaper yourself

Delete template?

Save as template?