GBC TITAN 1264WF/1244WF - Net

More documents

Recommendations

Info

GBC 1264WF/1244WFKnow your Laminator Continued-1.) Safety Shield: The Safety Shield aids in preventing theoperators fingers from becomingpinched or burned in the heat rollers ofthe laminator. With the Safety Shieldraised or removed, the machine goesinto the safety mode that prevents therun button on the control panel fromstarting the rollers to turn. The footpedal must be used when the SafetyShield is raised or removed.2.) Control Panel: The Control Panel enables the operatorto control motor run/stop, motordirection, motor speed, cooling fans, toptemperature, bottom temperature, jobnumber selection, job programming andtemperature reading.3.) Feed Table: The Feed Table supports the productthat is to be laminated. It also preventsfull access to the roller nip (where theupper and lower roller meet) of thelaminator. Because of this, thelaminator has been designed not tooperate when the Feed Table isremoved. Re-install the Feed Tablebefore attempting to operate thelaminator.4.) Lower Film Shaft/Unwind Shaft: The Lower Film Shaft/Unwind Shaftholds the lower film and allows the enduser to apply tension to the web.5.) Upper Film Shaft/Unwind Shaft: The Upper Film Shaft/Unwind Shaftholds the Upper film and allows the enduser to apply tension to the web.6.) Unwind Brake: The Unwind Brakes are used to applytension to the web.7.) Pressure Plate: The Pressure Plate assists in keeping theleading edge and the trailing edge of theprint flat when fed into the laminator.Operation Manual8.) Emergency Stop/E-Stop: The Emergency/E-Stops are a safetyfeature that allows the operator to stopthe rollers from rotating by depressingthem as needed.9.) Rewind Clutch Knob: The rewinder is clutch driven. As youincrease the tension on the RewindClutch Knob, the amount of force isincreased and increases the rate/strengthof the rewinder.10.) Rewind Shaft: The Rewind Shaft is driven by a clutchsystem. The greater you increase theclutch; the amount of force is increasedand increases the rate/strength of therewinder.11.) Rear Slitter: The Rear slitter is intended to cut theweb output from the laminator andshould not be used for any otherpurpose.12.) Power Switch: The Main Power Switch turns thelaminator on and off. It supplies powerto the laminator.13.) Foot Pedal: The Foot Pedal allows the operator tostart and stop the machine without usingthe Main Control Panel.14.) Power Cord: The Power cord comes with the machineand requires certain plug configurations.Please see the Specs to determinecorrect outlet configuration.15.) Web Clutch: Use the Web clutch to control tensionbetween the main rolls and the pullrollers. This will assist the end user inensuring good output.16.) Roll Lift Handle/Gap Adjust. Handle: Use this Handle to select the propersettings depending on what applicationis to be used.© 2006 General Binding Corporation Page 16
GBC 1264WF/1244WFOperation ManualSection 7: Display Control PanelStand-byPressing STAND-BY will cause thelaminator to go into the AUTO-OFF mode.The laminator will automatically go into thismode after sitting idle for an extendedamount of time. When in AUTO-OFF modethe laminator will no longer continue to heatthe main rollers to save power.Stand-byPressing MEMORY will cause the currentspeed and heat settings to be recorded in theJOB memory location shown on the display.JobsPressing the up or down arrows will causethe unit to cycle through stored jobs. Up to9 separate jobs can be stored. To save a job,select one of the nine jobs to overwrite.Then change the heat and speed settings asrequired for your application. Onceselected, press the memory button once.MeasurePress and hold the MEASURE key todisplay the current roller temperature.CoolingWhen the COOLING button is pressed thecooling fans will turn on or off. TheCOOLING button will illuminate greenwhen the fans are on. The fans blow freshair on the film web in between the heat andpull rollers.RunWhen the RUN is pressed the rollers willbegin turning. However, pressing run willnot cause the rollers to turn when any of thefollowing are true: the Emergency Stop isengaged, Safety Shield is raised or removedand/or the feed table is removed.© 2006 General Binding Corporation Page 17
Page 6 and 7: GBC 1264WF/1244WFOperation ManualPR
Page 10 and 11: GBC 1264WF/1244WFOperation ManualHe
Page 12 and 13: GBC 1264WF/1244WFOperation ManualSe
Page 14 and 15: GBC 1264WF/1244WFOperation Manual©
Page 18 and 19: GBC 1264WF/1244WFOperation ManualDi
Page 28 and 29: GBC 1264WF/1244WFOperation ManualWe
Page 30 and 31: GBC 1264WF/1244WFOperation ManualMe
Page 32 and 33: GBC 1264WF/1244WFOperation ManualTi
Page 34 and 35: GBC 1264WF/1244WFOperation ManualTi
Page 36 and 37: GBC 1264WF/1244WFOperation ManualHe
Page 38 and 39: GBC 1264WF/1244WFOperation ManualTR

GBC TITAN 1264WF/1244WF - Net

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?