Fire Alarm Control Panels - Bosch Security Systems
Fire Alarm Control Panels - Bosch Security Systems Fire Alarm Control Panels - Bosch Security Systems
90 en | Control Panel Programming Fire Alarm Control PanelsPROGRAM MUX1- MUX EDIT2- MUX PROGRAM3- BUS TYPE4- AUTO PROGRAM8.9.1MUX EditShortcut: 0-PROG, 9-PROGRAM MUX, 1- MUX EDITTo add MUX devices to the system, use the MUX Edit option. Each device must have a uniqueaddress programmed using the address switches.The following window appears:DEVICE TYPE ( )0- NO DEVICE2- SINGLE INPUT3- I/O MODULE4- MUX SMOKE5- SMOKE W/FRZ6- DUAL INPUT7- OCTAL INPUTDescriptionModel0- NO DEVICE2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class A)3- I/O MODULE D70534- MUX SMOKE D7050, D7050TH, D3435- SMOKE W/FRZ Not Used6- DUAL INPUT D7052(Class B)7- OCTAL INPUT D7042Press the number that corresponds with the device you are adding or press [0/Prog] if you areremoving a device. When the device type is selected, the following window appears:POINT NUMBER(009 - 255) 009Enter the address of the point being added, and press [#/Enter]. The device type windowappears again allowing additional devices to be added. Eight points are added at once whenthe D7042 is added to the control panel.8.9.2MUX ProgramShortcut: 0-PROG, 9-PROGRAM MUX, 2-MUX PROGRAMTo add MUX devices to the system simultaneously while programming an address into thedevice itself, use the MUX Program option. This programs a specified address into the device,and also sets the control panel to use the device.!Warning!Programming issues!The D7042 is programmed using switches and cannot be added using the MUX Program feature.Use MUX Edit instead.All devices must be removed from MUX bus A before programming by removing power fromthe system, disconnecting the wires to the field devices, and re-powering the system. Failureto disconnect devices results in all devices on loop A being programmed to the new address.All programming is performed on Bus A, including addresses 129 to 255 that can only beinstalled on Bus B for operation. Be sure to connect devices with addresses 129 to 255 toBus B, not to Bus A.2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 91If no devices are connected on Bus A, the following window appears. Otherwise an errormessage appears.PROGRAM MUX1- NORMAL2- FASTSelect normal programming to add one or two devices. Select fast programming to programlarger quantities of identical devices to sequential addresses.Normal ProgrammingIf normal programming is selected, the following menu appears allowing selection of thedevice type being programmed:DEVICE TYPE ( )0- NO DEVICE2- SINGLE INPUT3- I/O MODULE4- MUX SMOKE5- SMOKE W/FRZ6- DUAL INPUT7- OCTAL INPUTDescriptionModel0- NO DEVICE2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class A)3- I/O MODULE D70534- MUX SMOKE D7050, D7050TH, D3435- SMOKE W/FRZ Not Used6- DUAL INPUT D7052(Class B)7- OCTAL INPUT D7042Enter the number that corresponds with the device you are adding, or select 0 if you areremoving a device. When the device type is selected, the following window appears:POINT NUMBER(009 - 255) 009Enter the address of the point being added, and press [#/Enter]. The display asks you toattach the device being programmed to the terminals for MUX bus A (see the followingwindow). You can simply hold the device wires on the terminals for the few seconds it takesto program. The programming operation retries up to three times if the device does notconnect right away.POINT NUMBER 009ATTACH DEVICEThen, the display automatically shows:POINT NUMBER 009PROGRAMMINGIf the device added is an I/O module, you are asked to enter the four zones to control the relayoutput, just as for other relay devices:OUTPUT ZONE A: _______(00 - 63): _______Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similardisplay for Zone B, C and D appears allowing up to four zones to control this output. When allfour zones are assigned, the previous window appears. It confirms the programming operationand returns to the previous menu.POINT NUMBER 009PROGRAMMEDBosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
- Page 40 and 41: 40 en | System Operation Fire Alarm
- Page 42 and 43: 42 en | System Operation Fire Alarm
- Page 44 and 45: 44 en | System Operation Fire Alarm
- Page 46 and 47: 46 en | System Operation Fire Alarm
- Page 48 and 49: 48 en | System Operation Fire Alarm
- Page 50 and 51: 50 en | Programming Fire Alarm Cont
- Page 52 and 53: 52 en | Programming Fire Alarm Cont
- Page 54 and 55: 54 en | Programming Fire Alarm Cont
- Page 56 and 57: 56 en | Programming Fire Alarm Cont
- Page 58 and 59: 58 en | Programming Fire Alarm Cont
- Page 60 and 61: 60 en | Control Panel Programming F
- Page 62 and 63: 62 en | Control Panel Programming F
- Page 64 and 65: 64 en | Control Panel Programming F
- Page 66 and 67: 66 en | Control Panel Programming F
- Page 68 and 69: 68 en | Control Panel Programming F
- Page 70 and 71: 70 en | Control Panel Programming F
- Page 72 and 73: 72 en | Control Panel Programming F
- Page 74 and 75: 74 en | Control Panel Programming F
- Page 76 and 77: 76 en | Control Panel Programming F
- Page 78 and 79: 78 en | Control Panel Programming F
- Page 80 and 81: 80 en | Control Panel Programming F
- Page 82 and 83: 82 en | Control Panel Programming F
- Page 84 and 85: 84 en | Control Panel Programming F
- Page 86 and 87: 86 en | Control Panel Programming F
- Page 88 and 89: 88 en | Control Panel Programming F
- Page 92 and 93: 92 en | Control Panel Programming F
- Page 94 and 95: 94 en | Control Panel Programming F
- Page 96 and 97: 96 en | Control Panel Programming F
- Page 98 and 99: 98 en | Specifications Fire Alarm C
- Page 101 and 102: Fire Alarm Control Panels Appendice
- Page 103 and 104: Fire Alarm Control Panels Appendice
- Page 105 and 106: Fire Alarm Control Panels Appendice
- Page 107: Fire Alarm Control Panels Appendice
- Page 110 and 111: 110 en | Appendices Fire Alarm Cont
- Page 112 and 113: 112 en | Appendices Fire Alarm Cont
- Page 114 and 115: 114 en | Appendices Fire Alarm Cont
- Page 116 and 117: 116 en | Appendices Fire Alarm Cont
- Page 118 and 119: 118 en | Appendices Fire Alarm Cont
- Page 122: Bosch Security Systems, Inc.130 Per
90 en | <strong>Control</strong> Panel Programming <strong>Fire</strong> <strong>Alarm</strong> <strong>Control</strong> <strong>Panels</strong>PROGRAM MUX1- MUX EDIT2- MUX PROGRAM3- BUS TYPE4- AUTO PROGRAM8.9.1MUX EditShortcut: 0-PROG, 9-PROGRAM MUX, 1- MUX EDITTo add MUX devices to the system, use the MUX Edit option. Each device must have a uniqueaddress programmed using the address switches.The following window appears:DEVICE TYPE ( )0- NO DEVICE2- SINGLE INPUT3- I/O MODULE4- MUX SMOKE5- SMOKE W/FRZ6- DUAL INPUT7- OCTAL INPUTDescriptionModel0- NO DEVICE2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class A)3- I/O MODULE D70534- MUX SMOKE D7050, D7050TH, D3435- SMOKE W/FRZ Not Used6- DUAL INPUT D7052(Class B)7- OCTAL INPUT D7042Press the number that corresponds with the device you are adding or press [0/Prog] if you areremoving a device. When the device type is selected, the following window appears:POINT NUMBER(009 - 255) 009Enter the address of the point being added, and press [#/Enter]. The device type windowappears again allowing additional devices to be added. Eight points are added at once whenthe D7042 is added to the control panel.8.9.2MUX ProgramShortcut: 0-PROG, 9-PROGRAM MUX, 2-MUX PROGRAMTo add MUX devices to the system simultaneously while programming an address into thedevice itself, use the MUX Program option. This programs a specified address into the device,and also sets the control panel to use the device.!Warning!Programming issues!The D7042 is programmed using switches and cannot be added using the MUX Program feature.Use MUX Edit instead.All devices must be removed from MUX bus A before programming by removing power fromthe system, disconnecting the wires to the field devices, and re-powering the system. Failureto disconnect devices results in all devices on loop A being programmed to the new address.All programming is performed on Bus A, including addresses 129 to 255 that can only beinstalled on Bus B for operation. Be sure to connect devices with addresses 129 to 255 toBus B, not to Bus A.2012.08 | 04 | F01U008458 Installation and Operation Manual <strong>Bosch</strong> <strong>Security</strong> System, Inc.