Fire Alarm Control Panels - Bosch Security Systems
Fire Alarm Control Panels - Bosch Security Systems Fire Alarm Control Panels - Bosch Security Systems
84 en | Control Panel Programming Fire Alarm Control PanelsiNotice!If any reports are directed to Phone/IP Number 2 (including the default, PHONE 2 BACKUP), aphone number and account number must be programmed for Phone/IP Number 2. The controlpanel indicates a COMM FAULT if it sends a report (using Phone Number 1 parameters)which references unprogrammed Phone/IP Number 2 parameters.The display scrolls through the following items:REPORT STEERING1- NONSUP ALRM2- SUPVSY ALRM3- NONSUP RSTR4- SUPVSY RSTR5- TROUBLE6- TESTS7- SILENCE8- RESET9- FIRE DRILLPress the number key that corresponds to your selection. Selecting, for exampleNONSUP ALRM produces the following window:NONSUP ALRM (__)1- PHONE/IP 1 ONLY2- PHONE/IP 2 ONLY3- PHON/IP 1 AND 24- PHN/IP 2 BACKUP5- NO REPORTPHONE/IP 1 ONLY: Report sent to Phone/IP 1 only.PHONE/IP 2 ONLY: Report sent to Phone/IP 2 only.PHONE/IP 1 AND 2: Report sent to Phone/IP Numbers 1 and 2.PHONE/IP 2 BACKUP: Report sent to Phone/IP 1, then to Phone/IP 2 if 1 fails.NO REPORT: No report sent.Press the number key that corresponds with your selection. The previous window appears.8.6.4Ring CountShortcut: 0-PROG, 6-PROG ACC’NTS, 4-RING COUNTiNotice!Set to 0 the number of phone rings before the control panel seizes the line to attempt remoteprogramming. The number of phone rings before the panel seizes the line to attempt remoteprogramming must remain at 0 for UL864 local, auxiliary or remote station installations. If anIP address is entered in for the Phone/IP number, the panel will ignore this setting. When thering count is set to 0, remote programming must be answered on site. Once answered, thepanel will prompt for a password.The following window appears:2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 85RING COUNT(01-15, 00=DIS) _______Enter the information and press [#/Enter]. The previous window appears. An entry of [0/Prog][0/Prog] disables ring detection.For acceptable programming selections for UL864 9 th edition Listed applications, seeProgramming features for UL864, 49.8.6.5Communication TriesShortcut: 0-PROG, 6-PROG ACC’NTS, 5-COMM. TRIESThe system default is to try ten times to communicate an event. Bosch recommends settingthis to five tries. This parameter determines after which attempt the system indicates a failurecondition. (After reporting a failure, the system continues to communicate until it reaches tentimes). Do not select 1 or a failure is indicated whenever a report is sent.The following window appears:COMM ATTMPTS (__)(01-10): _______Enter the information and press [#/Enter]. The previous window appears.8.6.6Machine BypassShortcut: 0-PROG, 6-PROG ACC’NTS, 6-MACH BYPASSThe downloading computer must redial the control panel if an answering machine answeredthe phone before the control panel. When this option is selected, if the control panel detectsthe phone line ringing within one minute of when the last ringing cycle stopped, it answers onthe first ring and seizes the phone line. If an IP address is entered in for the Phone/IP number,the control panel ignores this setting.The following window appears:MACHINE BYPASS_______: YES (1) NO (0)Enter the information and press [#/Enter]. The previous window appears.8.6.7ALT. COMMShortcut: 0-PROG, 6-PROG ACC’NTS, 7-ALTER COMMThis prompt is used with the B420 models, DX4010, DX4020 or ITS-DX4020-G.If using the DX4010 select 1-serial; for all others, select 0-network. The following windowappears:ALTER COMM (_)0 – NETWORK1 - SERIAL8.7PROG FORMATSPROG FORMATS1 - 4/2 ZONE REPT2 - 4/2 RPT CODS3 - BFSK RPT CDSBosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
- Page 34 and 35: 34 en | Connection Fire Alarm Contr
- Page 36 and 37: 36 en | System Operation Fire Alarm
- Page 38 and 39: 38 en | System Operation Fire Alarm
- Page 40 and 41: 40 en | System Operation Fire Alarm
- Page 42 and 43: 42 en | System Operation Fire Alarm
- Page 44 and 45: 44 en | System Operation Fire Alarm
- Page 46 and 47: 46 en | System Operation Fire Alarm
- Page 48 and 49: 48 en | System Operation Fire Alarm
- Page 50 and 51: 50 en | Programming Fire Alarm Cont
- Page 52 and 53: 52 en | Programming Fire Alarm Cont
- Page 54 and 55: 54 en | Programming Fire Alarm Cont
- Page 56 and 57: 56 en | Programming Fire Alarm Cont
- Page 58 and 59: 58 en | Programming Fire Alarm Cont
- Page 60 and 61: 60 en | Control Panel Programming F
- Page 62 and 63: 62 en | Control Panel Programming F
- Page 64 and 65: 64 en | Control Panel Programming F
- Page 66 and 67: 66 en | Control Panel Programming F
- Page 68 and 69: 68 en | Control Panel Programming F
- Page 70 and 71: 70 en | Control Panel Programming F
- Page 72 and 73: 72 en | Control Panel Programming F
- Page 74 and 75: 74 en | Control Panel Programming F
- Page 76 and 77: 76 en | Control Panel Programming F
- Page 78 and 79: 78 en | Control Panel Programming F
- Page 80 and 81: 80 en | Control Panel Programming F
- Page 82 and 83: 82 en | Control Panel Programming F
- Page 86 and 87: 86 en | Control Panel Programming F
- Page 88 and 89: 88 en | Control Panel Programming F
- Page 90 and 91: 90 en | Control Panel Programming F
- Page 92 and 93: 92 en | Control Panel Programming F
- Page 94 and 95: 94 en | Control Panel Programming F
- Page 96 and 97: 96 en | Control Panel Programming F
- Page 98 and 99: 98 en | Specifications Fire Alarm C
- Page 101 and 102: Fire Alarm Control Panels Appendice
- Page 103 and 104: Fire Alarm Control Panels Appendice
- Page 105 and 106: Fire Alarm Control Panels Appendice
- Page 107: Fire Alarm Control Panels Appendice
- Page 110 and 111: 110 en | Appendices Fire Alarm Cont
- Page 112 and 113: 112 en | Appendices Fire Alarm Cont
- Page 114 and 115: 114 en | Appendices Fire Alarm Cont
- Page 116 and 117: 116 en | Appendices Fire Alarm Cont
- Page 118 and 119: 118 en | Appendices Fire Alarm Cont
- Page 122: Bosch Security Systems, Inc.130 Per
<strong>Fire</strong> <strong>Alarm</strong> <strong>Control</strong> <strong>Panels</strong> <strong>Control</strong> Panel Programming | en 85RING COUNT(01-15, 00=DIS) _______Enter the information and press [#/Enter]. The previous window appears. An entry of [0/Prog][0/Prog] disables ring detection.For acceptable programming selections for UL864 9 th edition Listed applications, seeProgramming features for UL864, 49.8.6.5Communication TriesShortcut: 0-PROG, 6-PROG ACC’NTS, 5-COMM. TRIESThe system default is to try ten times to communicate an event. <strong>Bosch</strong> recommends settingthis to five tries. This parameter determines after which attempt the system indicates a failurecondition. (After reporting a failure, the system continues to communicate until it reaches tentimes). Do not select 1 or a failure is indicated whenever a report is sent.The following window appears:COMM ATTMPTS (__)(01-10): _______Enter the information and press [#/Enter]. The previous window appears.8.6.6Machine BypassShortcut: 0-PROG, 6-PROG ACC’NTS, 6-MACH BYPASSThe downloading computer must redial the control panel if an answering machine answeredthe phone before the control panel. When this option is selected, if the control panel detectsthe phone line ringing within one minute of when the last ringing cycle stopped, it answers onthe first ring and seizes the phone line. If an IP address is entered in for the Phone/IP number,the control panel ignores this setting.The following window appears:MACHINE BYPASS_______: YES (1) NO (0)Enter the information and press [#/Enter]. The previous window appears.8.6.7ALT. COMMShortcut: 0-PROG, 6-PROG ACC’NTS, 7-ALTER COMMThis prompt is used with the B420 models, DX4010, DX4020 or ITS-DX4020-G.If using the DX4010 select 1-serial; for all others, select 0-network. The following windowappears:ALTER COMM (_)0 – NETWORK1 - SERIAL8.7PROG FORMATSPROG FORMATS1 - 4/2 ZONE REPT2 - 4/2 RPT CODS3 - BFSK RPT CDS<strong>Bosch</strong> <strong>Security</strong> System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Change language