Fire Alarm Control Panels - Bosch Security Systems
Fire Alarm Control Panels - Bosch Security Systems Fire Alarm Control Panels - Bosch Security Systems
76 en | Control Panel Programming Fire Alarm Control Panels8.5.2Programming relaysShortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYSThe main control panel includes three on-board relays (Relay 1, Relay 2, and Relay 3). TheFPD‐7024 can also support up to two D7035 Octal Relay Modules (Remote Relay 1 andRemote Relay 2), that offer a total of 16 remote relays (eight relays per module).The followingwindow appears:RELAY OUTPUTS1- LOCAL2- REMOTE 13- REMOTE 24- MULTIPLEXPress the number key that corresponds to your selection.iNotice!The option for multiplex relay programming is visible only if the D7039 Multiplex Expander isinstalled.Local RelaysShortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYSThe display scrolls through the Relay options.Press [1] for LOCAL. The following window appears:ONBOARD RELAY(1-3):Enter the number corresponding to the relay to be programmed and press [#/Enter]. Thedisplay asks you to enter four zones to activate this output:OUTPUT ZONE A:_______(00 - 63):_______Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similardisplay for Zones B, C and D will appear to allow up to four zones to be assigned to thisoutput. When all four zones are assigned, the previous window appears.For pre-assigned zones, see Pre-assigned zone quick reference, 74.An output point cannot be assigned to more than four zones. Each output does not need to beassigned to four zones. Each zone can have any number of outputs assigned to it.Remote relaysShortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYSThe display scrolls through the Relay options. Press [2] for REMOTE 1 or [3] for REMOTE 2.The following window appears:REMOTE RELAY @ x(1 - 8):2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 77iNotice!The @ x shows the address of the relay module in the system. The lower number address isRelay 1; the higher one is Relay 2.When you address a MUX Module, you assign an address. Ifyou have a dual point, it would have two consecutive addresses.Enter the relay you wish to assign and press [#/Enter]. The display shows:OUTPUT ZONE A:_______(00-63):_______Enter the output number (00 to 63) you want to assign to Zone A and press [#/Enter]. Asimilar display for Zone B appears. When all four zones are assigned, the previous windowappears.For pre-assigned zones, see Pre-assigned zone quick reference, 74.An output point cannot be assigned to more than four zones. Each output does not need to beassigned to four zones. Each zone can have any number of outputs assigned to it.Multiplex relaysShortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS!Warning!Do not use this menu to program addresses configured as inputs.The display scrolls through the Relay options. Press [4/◄] for MULTIPLEX. The followingwindow appears:MUX OUTPUT(009 - 255):Enter the number corresponding with the output to be programmed and press [#/Enter]. Theoutput number of a multiplex relay is the second point of an I/O module. Adding 1 to theaddress of the I/O module gives the address of the relay in the module. When the relay isselected, the display asks you to enter four zones to activate this output:OUTPUT ZONE A:_______(00 - 63):_______Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similardisplay for Zone B, C and D appears, allowing up to four zones be assigned to this input. Whenall four zones are assigned, the previous window appears.An output point cannot be assigned to more than four zones. Each output does not need to beassigned to four zones. Each zone can have any number of outputs assigned to it.8.6PROG ACCOUNTSPROG ACC’NTS1- PHONE / IP NUMS2- PHON CONTROL3- RPT STEERING4- RING COUNT5- COMM. TRIES6- MACH. BYPASSBosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
- Page 26 and 27: 26 en | Installation Fire Alarm Con
- Page 28 and 29: 28 en | Installation Fire Alarm Con
- Page 30 and 31: 30 en | Connection Fire Alarm Contr
- Page 32 and 33: 32 en | Connection Fire Alarm Contr
- Page 34 and 35: 34 en | Connection Fire Alarm Contr
- Page 36 and 37: 36 en | System Operation Fire Alarm
- Page 38 and 39: 38 en | System Operation Fire Alarm
- Page 40 and 41: 40 en | System Operation Fire Alarm
- Page 42 and 43: 42 en | System Operation Fire Alarm
- Page 44 and 45: 44 en | System Operation Fire Alarm
- Page 46 and 47: 46 en | System Operation Fire Alarm
- Page 48 and 49: 48 en | System Operation Fire Alarm
- Page 50 and 51: 50 en | Programming Fire Alarm Cont
- Page 52 and 53: 52 en | Programming Fire Alarm Cont
- Page 54 and 55: 54 en | Programming Fire Alarm Cont
- Page 56 and 57: 56 en | Programming Fire Alarm Cont
- Page 58 and 59: 58 en | Programming Fire Alarm Cont
- Page 60 and 61: 60 en | Control Panel Programming F
- Page 62 and 63: 62 en | Control Panel Programming F
- Page 64 and 65: 64 en | Control Panel Programming F
- Page 66 and 67: 66 en | Control Panel Programming F
- Page 68 and 69: 68 en | Control Panel Programming F
- Page 70 and 71: 70 en | Control Panel Programming F
- Page 72 and 73: 72 en | Control Panel Programming F
- Page 74 and 75: 74 en | Control Panel Programming F
- Page 78 and 79: 78 en | Control Panel Programming F
- Page 80 and 81: 80 en | Control Panel Programming F
- Page 82 and 83: 82 en | Control Panel Programming F
- Page 84 and 85: 84 en | Control Panel Programming F
- Page 86 and 87: 86 en | Control Panel Programming F
- Page 88 and 89: 88 en | Control Panel Programming F
- Page 90 and 91: 90 en | Control Panel Programming F
- Page 92 and 93: 92 en | Control Panel Programming F
- Page 94 and 95: 94 en | Control Panel Programming F
- Page 96 and 97: 96 en | Control Panel Programming F
- Page 98 and 99: 98 en | Specifications Fire Alarm C
- Page 101 and 102: Fire Alarm Control Panels Appendice
- Page 103 and 104: Fire Alarm Control Panels Appendice
- Page 105 and 106: Fire Alarm Control Panels Appendice
- Page 107: Fire Alarm Control Panels Appendice
- Page 110 and 111: 110 en | Appendices Fire Alarm Cont
- Page 112 and 113: 112 en | Appendices Fire Alarm Cont
- Page 114 and 115: 114 en | Appendices Fire Alarm Cont
- Page 116 and 117: 116 en | Appendices Fire Alarm Cont
- Page 118 and 119: 118 en | Appendices Fire Alarm Cont
- Page 122: Bosch Security Systems, Inc.130 Per
<strong>Fire</strong> <strong>Alarm</strong> <strong>Control</strong> <strong>Panels</strong> <strong>Control</strong> Panel Programming | en 77iNotice!The @ x shows the address of the relay module in the system. The lower number address isRelay 1; the higher one is Relay 2.When you address a MUX Module, you assign an address. Ifyou have a dual point, it would have two consecutive addresses.Enter the relay you wish to assign and press [#/Enter]. The display shows:OUTPUT ZONE A:_______(00-63):_______Enter the output number (00 to 63) you want to assign to Zone A and press [#/Enter]. Asimilar display for Zone B appears. When all four zones are assigned, the previous windowappears.For pre-assigned zones, see Pre-assigned zone quick reference, 74.An output point cannot be assigned to more than four zones. Each output does not need to beassigned to four zones. Each zone can have any number of outputs assigned to it.Multiplex relaysShortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS!Warning!Do not use this menu to program addresses configured as inputs.The display scrolls through the Relay options. Press [4/◄] for MULTIPLEX. The followingwindow appears:MUX OUTPUT(009 - 255):Enter the number corresponding with the output to be programmed and press [#/Enter]. Theoutput number of a multiplex relay is the second point of an I/O module. Adding 1 to theaddress of the I/O module gives the address of the relay in the module. When the relay isselected, the display asks you to enter four zones to activate this output:OUTPUT ZONE A:_______(00 - 63):_______Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similardisplay for Zone B, C and D appears, allowing up to four zones be assigned to this input. Whenall four zones are assigned, the previous window appears.An output point cannot be assigned to more than four zones. Each output does not need to beassigned to four zones. Each zone can have any number of outputs assigned to it.8.6PROG ACCOUNTSPROG ACC’NTS1- PHONE / IP NUMS2- PHON CONTROL3- RPT STEERING4- RING COUNT5- COMM. TRIES6- MACH. BYPASS<strong>Bosch</strong> <strong>Security</strong> System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458