Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

70 en | Control Panel Programming Fire Alarm Control PanelsEnter the description using the numeric, [Silence] and [History] keys, then press [#/Enter] tosave the description.8.4.2Point functionShortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTIONThere are 16 point functions, each of which has programmable features for: configuration(fire, waterflow, and so on), local only operation, silencing, and loop response.iNotice!At default, points 9 to 255 are programmed as Function 10 which is set as Fire. Function 11 isset as Supervisory. Function 04 is set as Waterflow 16 second.The following window appears:POINT FUNC. (__)(01 - 16):_______Enter the function number you wish to program and press [#/Enter]. The following windowappears:PROG FUNCT0- CONFIGURE1- LOCAL ONLY2- (reserved)3- SILENCABLE4- LOOP RESPONS5- (reserved) NXT FCT PREV FCTEnter the function you wish to program.ConfigureShortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION– Fire: When activated, the point shows FIRE ALARM on control panel and keypads,activates selected output devices, and sends a Fire Alarm report (if programmed). Firepoints are defaulted to a latch when first configured.– Waterflow: When activated, the point shows WATERFLOW ALARM on control panel andkeypads, activates selected output devices, and sends a Waterflow Alarm report (ifprogrammed). Waterflow points are defaulted to a non-verify characteristic when firstconfigured.– Supervisory: When activated, the point shows SUPERVISORY ALARM on control paneland keypads, and sends a Supervisory Alarm report (if programmed). Supervisory pointsare defaulted to a non-verify characteristic when first configured.– Reset: When activated, the point initiates a control panel-reset operation to clear alarmsand reset smoke detectors. Only points 1 to 8 can be configured as reset points.– Silence: When activated, the point initiates a control panel silence operation to turn offsounders if the control panel is configured to allow silencing. Only points 1 to 8 can beconfigured as silence points.2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 71– AC Fault: When activating, the control panel waits for the AC Delay Timer to expirebefore indicating or sending a trouble condition. When the timer expires, it shows an ACFault on the control panel and the trouble LED turns on.Enter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG FUNCTION options.Press [0/Prog] to select CONFIGURE. The following window appears:ACTVTN TYPE ( )1- FIRE2- WATERFLOW3-SUPERVISORY4- (reserved)5- RESET6- SILENCE7- AC FAULTPress the number key that corresponds to your selection. (The existing setting is shown inparentheses on the first line.) The previous window appears.Local onlyShortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTIONEnabling this feature provides the input point for local annunciation only, with nocommunicator report. Enter the point number you wish to program and press [#/Enter]. Thedisplay scrolls through the PROG FUNCTION options.Press [1] to select LOCAL ONLY. The following window appears:LOCAL ONLY_______: YES (1)NO(0)Press either [1] to enable or [0/Prog] to disable. The previous window appears.SilencingShortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTIONThis feature determines if an output zone (1 to 50) follows the Silence button (relays reset,NACs silence).Enter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG FUNCTION options.Press [3] to select SILENCEABLE. The following window appears:SILENCABLE? (FF)_______: YES (1)NO(0)Press [1] for relays to reset and NACs to silence when the Silence button is pressed, or press[0/Prog] for relays to remain latched until reset and NACs to continue sounding when theSilence button is pressed.iNotice!When an output is assigned to more than one zone, the programming of the zone that triggersthe output controls the output. When more than one zone triggers the output, if one of thezones is programmed as non-silencing, the output will be non-silencing.NOTICE!The previous window appears. FF indicates the function being programmed.Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6:
MethodenberichtBerliner pairfam Stu
Page 14 and 15:
14 en | Overview Fire Alarm Control
Page 17 and 18:
Fire Alarm Control Panels Overview
Page 19 and 20: Fire Alarm Control Panels Overview
Page 22 and 23: 22 en | Installation Fire Alarm Con
Page 30 and 31: 30 en | Connection Fire Alarm Contr
Page 36 and 37: 36 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 98 and 99: 98 en | Specifications Fire Alarm C
Page 101 and 102: Fire Alarm Control Panels Appendice
Page 107: Fire Alarm Control Panels Appendice
Page 110 and 111: 110 en | Appendices Fire Alarm Cont
Page 122:
Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

Create successful ePaper yourself

Delete template?

Save as template?