Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

26 en | Installation Fire Alarm Control Panels5. Install and tighten the remaining two screws in the bottom mounting holes.6. Knock out the desired wire entrances on the enclosure.For mounting hole locations, see the following figure:Figure 4.3: Enclosure iInstallation1 Control panel location 5 Transformer2 Mounting holes 6 Stud3 Retainer holes for standoffs 7 Ground wire4 Retainer holes for support postsiNotice!If using the knockouts located at the bottom of the enclosure, install batteries in a separateenclosure.4.3Installing the FPD‐7024Danger!The control circuit board in the FPD-7024 is static sensitive.To avoid damage to sensitive components, touch ground before handling the control board.This discharges any static electricity in your body. For example, run the ground wire to the enclosurebefore handling the control circuit board. Continue touching the enclosure while installingthe control board.2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Installation | en 27!Warning!Before the circuit board is installed, connect the supplied ground wires between the door andthe enclosure and from the transformer to the enclosure using the supplied nuts. Bothgrounds connect to the stud in the enclosure to the left of the circuit board.For installation illustrations, see the figures for Enclosue installation, 26 and for Standoff andsupport post installation, 27.1. Insert the three support posts in the enclosure’s retainer holes.2. Press the 1/8 in. nylon standoffs (P/N: F01U034705) into the retainer holes.3. Slide the top of the control panel onto the retainer tabs (the slots under the top of theframe). When the control panel is in the retainer tabs, it rests on the posts.4. Secure the bottom of the circuit board by inserting and tightening the screws at the twobottom corners through the support posts and the retainer holes.For installing standoffs and support posts, see the following figure:Figure 4.4: Standoff and support post installation1 1/8 in. nylon standoff 4 Corner of circuit board2 Retainer holes 5 Support post3 Support post assembly 6 Retainer hole in enclosure4.4Installing optional equipmentTwo expansion options connect directly to the control panel, and are automatically detectedand supervised when the control panel is powered:– FPC-7034 Four Point Expander– D7039 Multiplex Expansion ModuleWhen the control panel is powered after installing one of these options, the control paneldisplays one of the following windows:4Z EXP DETECTEDPRESS BACK KEYMUX DETECTEDPRESS BACK KEYPress the [*/BACK] key to confirm the installation of the device and automatically set it up forsupervision.Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6: MethodenberichtBerliner pairfam Stu
Page 14 and 15: 14 en | Overview Fire Alarm Control
Page 17 and 18: Fire Alarm Control Panels Overview
Page 19 and 20: Fire Alarm Control Panels Overview
Page 22 and 23: 22 en | Installation Fire Alarm Con
Page 30 and 31: 30 en | Connection Fire Alarm Contr
Page 36 and 37: 36 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 76 and 77:
76 en | Control Panel Programming F
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
98 en | Specifications Fire Alarm C
Page 101 and 102:
Fire Alarm Control Panels Appendice
Page 103 and 104:
Page 105 and 106:
Page 107:
Page 110 and 111:
110 en | Appendices Fire Alarm Cont
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 122:
Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

Create successful ePaper yourself

Delete template?

Save as template?