Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

24 en | Installation Fire Alarm Control PanelsFigure 4.1: Wiring the D132B smoke power reversing module1 Power limited and supervised 7 12/24 VDC2 Optional alarm latch 8 24 V reversing detectors3 Loop 9 2.2 kΩ EOL (power limited andsupervised)4 Class A 10 Not used5 Latch 11 24 V NACs6 NACD185 Reverse Polarity ModuleThe D185 Reverse Polarity Module is a UL Listed module that connects the control panel witheither a single set or a pair of leased telephone company (TELCO) lines in NFPA 72 remotestation applications. It relays system alarm status information from the control panel to amonitoring station. The D185 operates with either 12 VDC or 24 VDC supply.For typical wiring of the D185 module, see the following figure:2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Installation | en 25Figure 4.2: Wiring the D1851 D185 module 5 Fire control panel2 To monitoring station bk black3 D275 bu blue4 2.2 kΩ EOL ye yellowThe module can signal alarm, trouble, and supervisory conditions. The Wiring the D185 figure,24 shows the module being used to signal alarm and trouble conditions only. With a third relay(available from the eight-relay expansion module) and an additional leased line, supervisoryconditions can also be signaled.In the example in the Wiring the D185 figure, Relay 1 must be programmed to operate onAlarm (Zone 63) and Relay 2 must be programmed to operate on Trouble (Zone 62). ProgramInput 4 to operate as a Supervisory point. Any alarm causes the voltage to the monitoringstation to be interrupted. Placing the D185 in test mode causes a SUPERVISORY TROUBLE.See also the D185 Installation Manual.4.2Installing the enclosureTo install the enclosure, follow these instructions:1. Using the enclosure as a template, mark the top mounting holes on the mounting surface.2. Start the mounting screws (not supplied) for these two holes.3. Slide the enclosure onto these screws so that the screws rest on the thinner section ofthe holes.4. Tighten the screws.Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6: MethodenberichtBerliner pairfam Stu
Page 14 and 15: 14 en | Overview Fire Alarm Control
Page 17 and 18: Fire Alarm Control Panels Overview
Page 19 and 20: Fire Alarm Control Panels Overview
Page 22 and 23: 22 en | Installation Fire Alarm Con
Page 30 and 31: 30 en | Connection Fire Alarm Contr
Page 36 and 37: 36 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 74 and 75:
74 en | Control Panel Programming F
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
98 en | Specifications Fire Alarm C
Page 101 and 102:
Fire Alarm Control Panels Appendice
Page 103 and 104:
Page 105 and 106:
Page 107:
Page 110 and 111:
110 en | Appendices Fire Alarm Cont
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 122:
Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

Create successful ePaper yourself

Delete template?

Save as template?