FTR1 Series Troffer Retrofit Kit Installation Instructions

FTR1 SeriesTroffer Retrofit KitInstallation InstructionsSAFETY:- This fixture must be wired in accordance with the National Electric Code and applicable local codes or ordinances.- All work should be performed by a qualified electrician.- To insure personal safety, proper grounding is required (connect green fixture lead to supply ground).- Handle fixture with care to avoid possible cuts or abrasions from exposed metal edges. We recommend wearinggloves when installing this kit.Contents:(1) Body with prewired ballast (with luminaire disconnect) & lampholders(1) Ballast Cover; (2) End caps; (2) Diffuser(1) Hardware Kit Containing:(6) ½” #8-32 self tapping screws (A)(4) 1/2” 8-32 Tek screws (B)(2) Installation tethers(2) #8-32 installation nutsBallastCoverBodyDiffuserEnd Caps1025-000000-052 r03

WARNINGS:-Risk of fire or electric shock. Reflector kit installation requires knowledge of fluorescent lighting luminaire electricalsystems. If not qualified, do not attempt installation. Contact a qualified electrician.-Reflector kit is not intended to be used in wet or damp locations.-Reflector kit is intended for use only with Surface Mounted or Type Non-IC Recessed Luminaires.-Risk of fire or electric shock. Install this kit only in a grounded luminaire that is UL Listed and has the constructionfeatures and dimensions shown in the photographs and/or drawings.-To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.-Risk of fire or electric shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when drilling forinstallation of reflector kit hardware. Check for enclosed wiring and components.-Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.-Not suitable for use on aluminum luminaires.Installation Instructions:1) Turn off power to fixture. Remove lens/door, lamps, ballasts, lampholders, and socket barsfrom the existing fixture.2) Install the end caps into the ends of the fixture byinserting the bottom flange between the bottom of thefixture and the T-bar. The end cap with tethers goesnearest the power supply wires. Center the end capand attach it using the provided tek screws throughthe two holes at the top of the bracket. The use of anelectric screwdriver with magnetic socket isrecommended. Repeat on the opposite end.3) Ensuring the lamp side of the reflector kit faces away fromtroffer interior, suspend the body by threading tethersthrough long oblong holes (start with side that has tab).4) Insert the supply leads (black & white) throughthe access hole. Do not connect wires to theLuminaire Disconnect plug. Do not disconnect theground wire on the existing fixture.5) Swing the body into the housing. Be careful not toscratch end caps. Attach the body (by sliding the clearanceslots carefully over the screws on the end caps) first to theend opposite the tethers and fasten using self- tappingscrews. Fasten tether end next.1025-000000-052 r03

6) Complete wiring by inserting the supply leads intothe appropriately marked (black and white) cavitieson the luminaire disconnect.7) Slide one side of the ballast cover into the tabs.Compress and release the ballast cover to fit intoother tabs as shown.8) Install lamps and make sure that the index markon the lamp end faces out of socket top opening.9) Attach the diffusers on either side of the ballastcover using the pins on the end bracket to completeretrofit kit installation.10) Apply power.WARNING: Improper seating of lamps can createa fire hazard. Whether field or factory installed, ensurelamp position is correct before energizing fixture. SeeDiagrams 1 and 2.Diagram 1-T8 lamp seatingThe dimple on the lampbase is aligned with the slotin the lamp holder.Diagram 2-T5 lamp seatingThe flat surface of the lampbase is perpendicular to theslot in the lamp holder.1025-000000-052 r03