DEEP SEA ELECTRONICS PLC - Home Mega Global Solution
DEEP SEA ELECTRONICS PLC - Home Mega Global Solution DEEP SEA ELECTRONICS PLC - Home Mega Global Solution
DSE 5xxx Configuration Software Manual5 SETUP MENU OPTIONS5.1 LOCAL PC OPTIONSThis menu is used to access the software configuration file, to customise the way the softwareoperates with the PC system. When selected the following is displayed:74DSE 5xxx Configuration software ISSUE 2 02/07/04 AM
DSE 5xxx Configuration Software ManualSetupCommunicationsSettingsFunctionCommunications settings configure how the software is to communicatewith the module.P810 interface : This option configures the software to use the P810interface (connected into the module’s 810 port) to communicate with the5xxx series controllers.RS232 modem : This option configures the software to communicate withthe controller via an RS232 modem using either a fixed land linetelephone system (PSTN) or GSM modem over the GSM network.RS485 : This option configures the software to communicate with thecontroller over an RS485 cable connection.Change COM Port (COM2) -This menu option is used to configure the software to use the appropriateCOM port on the PC. The COM ports are the RS232/RS485 interfaceterminals normally located on the rear of the PC, the moduleconfiguration software can use any one of these ports. A check should bemade to ensure that the ports are not already in use by other sourcessuch as mouse drivers or modems.Normally COM2 is the spare port with COM1 being used by a mouse.This can vary from PC to PC, so it is recommended that you check yourconfiguration by referring to the documentation supplied with your PC orby contacting your PC support personnel. Should you still experienceproblems contact DEEP SEA ELECTRONICS for assistance.When using the USB version of P810 interface the USB driver will createa ‘virtual COM port’ (i.e. COM6). This must be selected in the setup tabfor the P810 USB to operate. The ‘virtual COM port’ may only be visiblewhen the P810 USB is connected to the PC.Baud rate (RS485 only) : The baud rate over which the RS485communications will take place.Slave ID (RS485 only) : TheModbus Slave ID of the controler youwish to communicate with.Telephone number of module (RS232 only) : The telephone number todial (via modem) in order to communicate with the module.NOTE:- A quick check of correct communication with themodule can be made by selecting the Remote instrumentationtab, if no ‘Heartbeat’ is displayed this indicates that acommunications link has not been established. Check the COMport setting as described above.DSE5xxx Configuration software ISSUE 2 02/07/04 AM 75
- Page 24 and 25: DSE 5xxx Configuration Software Man
- Page 26 and 27: DSE 5xxx Configuration Software Man
- Page 28 and 29: DSE 5xxx Configuration Software Man
- Page 30 and 31: DSE 5xxx Configuration Software Man
- Page 32 and 33: DSE 5xxx Configuration Software Man
- Page 34 and 35: DSE 5xxx Configuration Software Man
- Page 36 and 37: DSE 5xxx Configuration Software Man
- Page 38 and 39: DSE 5xxx Configuration Software Man
- Page 40 and 41: DSE 5xxx Configuration Software Man
- Page 42 and 43: DSE 5xxx Configuration Software Man
- Page 44 and 45: DSE 5xxx Configuration Software Man
- Page 46 and 47: DSE 5xxx Configuration Software Man
- Page 48 and 49: DSE 5xxx Configuration Software Man
- Page 50 and 51: DSE 5xxx Configuration Software Man
- Page 52 and 53: DSE 5xxx Configuration Software Man
- Page 54 and 55: DSE 5xxx Configuration Software Man
- Page 56 and 57: DSE 5xxx Configuration Software Man
- Page 58 and 59: DSE 5xxx Configuration Software Man
- Page 60 and 61: DSE 5xxx Configuration Software Man
- Page 62 and 63: DSE 5xxx Configuration Software Man
- Page 64: DSE 5xxx Configuration Software Man
- Page 67 and 68: DSE 5xxx Configuration Software Man
- Page 69 and 70: DSE 5xxx Configuration Software Man
- Page 71 and 72: DSE 5xxx Configuration Software Man
- Page 73: DSE 5xxx Configuration Software Man
- Page 77 and 78: DSE 5xxx Configuration Software Man
- Page 79 and 80: DSE 5xxx Configuration Software Man
- Page 81 and 82: DSE 5xxx Configuration Software Man
- Page 83 and 84: DSE 5xxx Configuration Software Man
- Page 85 and 86: DSE 5xxx Configuration Software Man
- Page 87: DSE 5xxx Configuration Software Man
DSE 5xxx Configuration Software Manual5 SETUP MENU OPTIONS5.1 LOCAL PC OPTIONSThis menu is used to access the software configuration file, to customise the way the softwareoperates with the PC system. When selected the following is displayed:74DSE 5xxx Configuration software ISSUE 2 02/07/04 AM