Anayet Ullah patwari - Science Development Network

Dr. Mohammed. Anayet Ullah Patwari- Curriculum Vitaeprediction model of Cutting Force by Cutting Parameters using Response SurfaceMethodology in End Milling of Steel AISI1020, Proceedings of 2nd International & 23 rdAll India Manufacturing Technology, Design and Research conference , December 15-17, 2008, IIT (Madras) India39. S. Alam, AKM Nurul Amin, Anayet U Patwari, M. Konneh, “Development of aStatistical Model for the Prediction of Surface Roughness in High Speed End-Milling ofTi-6Al-4V”, Proceedings of 2nd International & 23 rd All India ManufacturingTechnology, Design and Research conference, December 15-17, 2008, IIT (Madras)India40. M.H Ishtiyaq, AKM Nurul Amin, Anayet U Patwari, Improvement of Machinability bywork piece preheating in end milling of Ti–6Al–4V”, Proceedings of 9 th Global congresson Manufacturing and Management (GCMM), page 248-254, 12-14 th November 2008,Surfers, paradise, holiday Inn, gold coast, Australia41. M.H Ishtiyaq, AKM Nurul Amin, Turnad L Gintoo, Anayet U Patwari, Application ofResponse Surface methodology coupled with Genetic Algorithm in the optimization ofcutting conditions for surface roughness in end milling of Inconel 718- Proceedings ofLEM, paper ID 115, page 285-290, 07-09 November 07, Fukoka, Japan.42. Anayet U Patwari, AKM Nurul Amin, Waleed F Faris, M.H Ishtiyaq “Development ofa Mathematical model for the Prediction of Chip Formation Instability and itsverification by Fuzzy logic with genetic algorithm”-Proceedings of ICME 2007, paperAM-29, 29-31, December 07 BUET, Dhaka43. Turnad L. Ginta, A.K.M. Nurul Amin, A.N.M Karim, Anayet U. Patwari, M.A.Lajis,“Tool Wear Morphology and Chip Segmentation in End Milling Titanium Alloy Ti–6Al–4V”, Proceedings of International conference of Curtin university of Science andTechnology engineering (CUTSE 2008) to be held Curtin university of Technology,Sarawak, Malaysia, 24-27 th November 2008.44. M.H Ishtiyaq, AKM Nurul Amin, Anayet U Patwari “Development of a artificialneural network algorithm for the prediction of surface roughness in end milling ofInconel 718”-Proceedings of International conference of computer and communicationengineering (ICCCE08), 13-15 May 2008, KL, Malaysia organized by Faculty ofEngineering, International Islamic university of Malaysia.45. N. A Chowdhury Anayet U. Patwari “Simulation of Elastic Field during Unloading inSurface rolling / burnishing” proceedings of the 11 th Annual Paper Meet, The Institutionof Engineers (IEB), Bangladesh, Mechanical Engineering Division, pp 239-244, 25-26December 2006.46. N. A Chowdhury Anayet U. Patwari & S.L Mahmud “Development of a post-processorfor metal forming process” Proceedings of summer computer simulation conference2006, page 49-53, July 30 to August 03, 2006, Alberta, Canada.47. Anayet U. Patwari, N. A Chowdhury & S.L Mahmud “Development of an optimizationtechnique by Fuzzy logic to predict the optimum process parameter for Deep drawingprocess” proceedings of modeling and simulation conference 2006, 03-05 April 2006,Malaysia, pp 582-586, paper code 183.48. N. A Chowdhury & Anayet U. Patwari “Designing and Controlling of a Pick and PlaceRobot”, proceedings of the 5 th International Mechanical Engineering Conference & 10 thAnnual Paper Meet, The Institution of Engineers (IEB), Bangladesh, MechanicalEngineering Division, pp 211-216, 30 Sept-02 October 2005.Page - 8 - of 10Knowledge Based Engineering Education with Values, Ethics and Character for Human Capital and Societal Developmentfor Community Services in OIC countries

Dr. Mohammed. Anayet Ullah Patwari- Curriculum VitaeExhibition 2007 (KERIE’07), Faculty of Engineering, International IslamicUniversity of Malaysia Bronze Medal for the research project on “Development of a Artificial Neural NetworkModel for the prediction of Cutting Forces in End Milling of Inconel 718”- M.H Isthiyaq,AKM Nurul Amin, Anayet U. Patwari, Kulliyah of Engineering Research andInnovation Exhibition 2007, (KERIE’07) Faculty of Engineering,International Islamic university of Malaysia Bronze Medal for the research project on “Elimination of conventional finishingoperations applying high speed end milling of aero space alloy Ti6Al4V using geneticalgorithm”- Shah Alam, AKM Nurul Amin, Konneh, Md. Anayet U Patwari, Kulliyahof Engineering Research and Innovation Exhibition 2009, Faculty ofEngineering, International Islamic university of Malaysia.____________________Sd-_________________(Mohammed Anayet Ullah Patwari)Assistant ProfessorIUT (OIC), Dhaka, BangladeshPage - 10 - of 10Knowledge Based Engineering Education with Values, Ethics and Character for Human Capital and Societal Developmentfor Community Services in OIC countries