STG-Beikirch
STG-Beikirch
STG-Beikirch
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
12 mal blinken<br />
12 times flash<br />
13 mal blinken<br />
13 times flash<br />
14 mal blinken<br />
14 times flash<br />
Fehlercodes<br />
Versorgung +5 V<br />
Der mitlaufende Selbsttest hat einen<br />
internen Fehler festgestellt.<br />
Abhilfe:<br />
- Das Modul zum Service einschicken.<br />
Achtung: Ein sicherer Weiterbetrieb<br />
ist nicht gewährleistet!<br />
Akkucharge<br />
Der mitlaufende Selbsttest hat eine fehlerhafte<br />
Verbindung zum Akku festgestellt.<br />
Abhilfe:<br />
- Prüfen, ob die Akkusicherung in<br />
Ordnung ist.<br />
- Prüfen, ob die Verdrahtung zum Akku in<br />
Ordnung ist, insbesondere Klemmen:<br />
1 und 5.<br />
- Prüfen, ob der Akku in Ordnung ist, ggf.<br />
austauschen.<br />
- Falls nichts hilft, Modul austauschen.<br />
SupplyUB<br />
Der mitlaufende Selbsttest hat einen<br />
internen Fehler festgestellt.<br />
Abhilfe:<br />
- Modul austauschen.<br />
Dauerleuchten grüne LED: Kein Fehler<br />
Technische Daten<br />
Error detecting codes<br />
Supply +5 V<br />
The continuous self test has discovered an<br />
internal error.<br />
Remedial Measure:<br />
- Send the module into the service<br />
department.<br />
Warning: Further safe operation can<br />
no longer be guaranteed.<br />
Battery charge<br />
The continuous self test has discovered a<br />
faulty battery connection.<br />
Remedial Measure:<br />
- Check that the battery fuse is ok.<br />
- Check that the wiring to the battery is in<br />
order, in particular terminals: 1 and 6.<br />
- Check if the battery is ok, replace if<br />
necessary.<br />
- If nothing helps replace the module.<br />
SupplyUB<br />
The continuous self test has discovered an<br />
internal error.<br />
Remedial Measure:<br />
- Replace module.<br />
Green LED continous lamp: No error<br />
Betriebsspannung des Moduls 230 V AC, 50 Hz (+/-15%)<br />
Ausgangsspannung 27 V DC (+/-15%)<br />
Max. Ausgangsstrom 16 A (ED 30: 3 Minuten EIN, 7 Minuten AUS)<br />
Max. Strom pro Aktorkreis (als Motorkreis/Linearantrieb ED 30) 8 A (ED 30: 3 Minuten EIN, 7 Minuten AUS)<br />
Aktorenkreise 4<br />
Max. Strom pro Aktorkreis (Haftmagnetkreis ED 100) 2,4 A (ED 100: ständig EIN)<br />
Max. Strom Modulversorgungungskreis 3 A<br />
Max. Akku Ladestrom 1,5 A<br />
Stromaufnahme (Nennstrom)<br />
2,5 A<br />
Stromaufnahme im Notbetrieb 4,3 mA (bei 27,5 V Betriebsspannung)<br />
Leistungsaufnahme im Notbetrieb 0,18 VA (bei 27,5 V Betriebsspannung)<br />
Akkukapazitäten 24 V; 1,2 - 18 Ah<br />
Akkutyp Bleigel, VdS geprüft<br />
Temperaturbereich 0° - 50 °C<br />
Feuchtigkeitsbereich 10 - 75 % rel. Feuchte, Betauung nicht zulässig<br />
Schutzklasse (Bestimmt durch MZ2 Aufbau)<br />
TÜV-Nr. 2175/05<br />
Technical dates<br />
Module operating voltage 230 V AC, 50 Hz (+/- 15%)<br />
Output voltage 27 V DC (+/- 15%)<br />
Max. output current 16 A (ED 30: 3 Minutes ON, 7 Minutes OFF)<br />
Max. power per actuator circuit (as motor circuit / linear drive ED 30) 8 A (ED 30: 3 Minutes ON, 7 Minutes OFF)<br />
Actuator circuits 4<br />
Max. Power per actuator circuit (adhesive magnet circuit ED 100) 2.4 A (ED 100: constant ON)<br />
Max. Power module supply circuit 3 A<br />
Max. Battery charging current 1.5 A<br />
Power consumption (rated current) 2.5 A<br />
Power consumption in emergency operation 4.3 mA (at 27.5 V operating voltage)<br />
Power consumption in emergency operation 0.118 W (at 27.5 V operating voltage)<br />
Battery capacities 24 V; 1.2 - 18 Ah<br />
Battery type Lead gel, VdS tested<br />
Temperature range 0° - 50°C<br />
Humidity range 10 - 75% re. humidity moisture not permitted<br />
Protection class (determined by MZ2 set up)<br />
TÜV No. 2175/05<br />
8