GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...
GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ... GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...
4.19.2 Start BatchActivation MethodThe batch begins with the selected activation method. The method is determined bythe parameters in the setup mode. The deactivation of the setpoints is automatic. Thedesired target may be based on net or quantity (if counting is enabled).Activation typeslllTare key - Press the [TARE] key to start the process. A tare weight will be setand the weight will switch to net zero.Remote key - Press the remote key switch.Auto-start - The process is automatically activated. It waits for a no-motioncondition and then adds the target to the current displayed weight to achievea relative cutoff value.AnnunciatorsIndication on the display showing the status of a relay. If the annunciator is illuminated,the corresponding setpoint is active.In order for the annunciators to activate, the displayed value must be at least fivegraduations above zero.Batch Status Annunciator Status Setpoint Status (Requires Setpoint Option Board)Fill 1 SP 1 Illuminated Relay 1 Contacts Closed, Relay 2 and 3 Contacts OpenFill 2 SP 2 Illuminated Relay 2 Contacts Closed, Relay 1 and3 Contacts OpenFill 3 SP 3 Illuminated Relay 3 Contacts Closed, Relay 1 and 2 Contacts OpenBatch ExampleWith a system set up a system to make a 50,000 lb batch with water (30,000 lbs.), cornsyrup (15,000 lbs.) and caramel color (5,000 lbs.), ingredient 1 should start with [TARE]and subsequent ingredients should auto-start.ParameterSettingActual Cutoff ValueCommentsTarget 1 = 30,000Desired water weight.Pre-Act 1 = 100 30,000 - 100 = 29,900 Water valve closes at 29,900 lbs. Free-fallwill bring weight to 30,000.Start 1 = TareStart water with [TARE].Target 2 = 15,000Desired corn syrup weight.86Model 350 I.S. and Model 355 I.S. Service Manual
ParameterSettingPre-Act 2 = 236 15,000 - 236 = 14,764 Corn syrup valve closes at 14,764 lbs.Free-fall will bring weight to 15,000.Start 2 = AutoActual Cutoff ValueCalculated cutoff value forcorn syrup is added tocurrent displayed weightCommentsStart corn syrup when water is done andmotion has stopped.Target 3 = 5,000Desired caramel coloring weight.Pre-Act 3 = 142 5,000 - 142 = 4,858 Carmel coloring valve closes at 4,858.Free-fall will bring weight to 5,000.Start 3 = Auto Calculated cutoff value forcaramel coloring is addedto current displayed weightStart caramel coloring when corn syrup isdone and motion has ceased.4.20 DischargeThe discharge program is designed for single-speed or dual-speed dispensing ofproduct from a larger weigh vessel. Discharge is a loss-in-weight application similar inoperation to the fill program. When a discharge is initiated, the scale automatically taresand comes to a net zero weight. The appropriate setpoints are activated and materialis discharged until the decreasing net weight reaches the desired target value. Freefalling product can be accounted for with the use of pre-act values (PA1 - PA3). Thisfeature must be enabled before attempting to use.SetpointSelectionFunctionDescriptionP5100.1 Discharge Select discharge setpoint operation.P5101.-- Targ1 Final dispensed target value.P5104.0 Based Select between net or count (quantity)P5105.-- PA 1 Pre-act 1 value (fast-to-slow value; 0 for single-speed).P5107.0 Start 1 Setpoint activation method.P5109.-- PA 2 Pre-act 2 value (final cutoff).P5110.1 Learn 2 Learn feature for pre-act 2.P5114.1 PrAc 1 Pre-act 1 available as subset in Weigh Mode.P5115.1 PrAc 2 Pre-act 2 available as subset in Weigh Mode.P5116.1 Pause Keypress invokes pause.4.20.1 Enter a TargetModel 350 I.S.1. Press [SELECT] until tArG1 is displayed.2. Press [PRINT] until the first digit of the new target is displayed. Press [UNITS]to accept the number displayed. Continue this step until the desired number isentered.Model 350 I.S. and Model 355 I.S. Service Manual 87
- Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
- Page 39 and 40: Battery ChargingTHE BATTERY MUST BE
- Page 41 and 42: 3. Snap the (4) ½ plastic standoff
- Page 43 and 44: Figure 3.12 Fiber-optic Cable Insta
- Page 45 and 46: Install the setpoint or Analog opti
- Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
- Page 49 and 50: 4 ConfigurationThis section covers
- Page 51 and 52: To access the previous parameter1.
- Page 53 and 54: To setup a full scale value (exampl
- Page 55 and 56: 4.5.2 Return to factory default (35
- Page 57 and 58: ParameterNumberDisplayNameP296.00 E
- Page 59 and 60: P115 Stability Delay (Selection)Sel
- Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
- Page 63 and 64: P292 End Character (Key-in)Set the
- Page 65 and 66: P802 Tare and Zero Execution (Selec
- Page 67 and 68: is an 'O' (overload/underload), 'M'
- Page 69 and 70: 4.9 ID Number Entry and PrintingIt
- Page 71 and 72: 4.10.4 Entering ASCII Control Codes
- Page 73 and 74: The default format code for all par
- Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
- Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
- Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
- Page 81 and 82: Pre-act values are entered in terms
- Page 83 and 84: 4. Next the PctHi value will be dis
- Page 85 and 86: 3. Press [TARE]. Once the tare key
- Page 87: 4.19.1 Enter a TargetPressing [TARE
- Page 91 and 92: 4.20.3 Start DischargeActivation Me
- Page 93 and 94: 3a. If a value is desired, enter it
- Page 95 and 96: 4.22 Absolute CheckweighThis progra
- Page 97 and 98: 4.23 Target Deviation CheckweighThe
- Page 99 and 100: 4.24 Batch 2The batch 2 program is
- Page 101 and 102: 4.25 Independent Setpoint Operation
- Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
- Page 105 and 106: Bars ON Weight Range (Lower Toleran
- Page 107 and 108: ParameterSettingDisplayedNameDescri
- Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
- Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
- Page 113 and 114: ParameterSettingDisplayedNameDescri
- Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
- Page 117 and 118: 4.28.5 300 Series Command CodesHex
- Page 119 and 120: 5 CalibrationThis chapter covers al
- Page 121 and 122: First Zero Calibration Method (355
- Page 123 and 124: 9. Pause for motion delay.10. Press
- Page 125 and 126: 13. Pause for motion delay.14. Pres
- Page 127 and 128: If the calibration weight value was
- Page 129 and 130: 6 Legal for TradeThe Model 350/355
- Page 131 and 132: 6.4.1 Physical SealThe most common
- Page 133 and 134: 7 TroubleshootingThis chapter conta
- Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
- Page 137 and 138: Table 7.1 Information Parameters.Pa
ParameterSettingPre-Act 2 = 236 15,000 - 236 = 14,764 Corn syrup valve closes at 14,764 lbs.Free-fall will bring weight to 15,000.Start 2 = AutoActual Cutoff ValueCalculated cutoff value forcorn syrup is added tocurrent displayed weightCommentsStart corn syrup when water is done andmotion has stopped.Target 3 = 5,000Desired caramel coloring weight.Pre-Act 3 = 142 5,000 - 142 = 4,858 Carmel coloring valve closes at 4,858.Free-fall will bring weight to 5,000.Start 3 = Auto Calculated cutoff value forcaramel coloring is addedto current displayed weightStart caramel coloring when corn syrup isdone and motion has ceased.4.20 DischargeThe discharge program is designed for single-speed or dual-speed dispensing ofproduct from a larger weigh vessel. Discharge is a loss-in-weight application similar inoperation to the fill program. When a discharge is initiated, the scale automatically taresand comes to a net zero weight. The appropriate setpoints are activated and materialis discharged until the decreasing net weight reaches the desired target value. Freefalling product can be accounted for with the use of pre-act values (PA1 - PA3). Thisfeature must be enabled before attempting to use.SetpointSelectionFunctionDescriptionP5100.1 Discharge Select discharge setpoint operation.P5101.-- Targ1 Final dispensed target value.P5104.0 Based Select between net or count (quantity)P5105.-- PA 1 Pre-act 1 value (fast-to-slow value; 0 for single-speed).P5107.0 Start 1 Setpoint activation method.P5109.-- PA 2 Pre-act 2 value (final cutoff).P5110.1 Learn 2 Learn feature for pre-act 2.P5114.1 PrAc 1 Pre-act 1 available as subset in <strong>Weigh</strong> Mode.P5115.1 PrAc 2 Pre-act 2 available as subset in <strong>Weigh</strong> Mode.P5116.1 Pause Keypress invokes pause.4.20.1 Enter a TargetModel 350 I.S.1. Press [SELECT] until tArG1 is displayed.2. Press [PRINT] until the first digit of the new target is displayed. Press [UNITS]to accept the number displayed. Continue this step until the desired number isentered.Model 350 I.S. and Model 355 I.S. <strong>Service</strong> <strong>Manual</strong> 87