GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...
GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ... GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...
In order for the annunciators to activate, the displayed value must be at least fivegraduations above zero.Fill StatusFast FillDribble Fill (or Single-Speed Fill)Fill Done or PauseAnnunciator StatusSP 1 & SP 2 IlluminatedSP 1 IlluminatedSP 1 & SP 2 OffFill ExampleWith a system set up to fill 55-gallon drums with motor oil, the following settings mightbe used to achieve an accurate final fill weight of 400 lbs.:ParameterSettingActual Cutoff ValueCommentsTarg 1 = 400Desired final weight.Pre-act 1 = 28 400 - 28 = 372.0 Switch to dribble feed at 372.Pre-act 2 = .5 400 - 0.5 = 399.5 Final fill valve closes at 399.5.4.19 BatchThe standard batch program is used for batching up to three separate items.Ingredients 1 through 3 use setpoints and pre-acts 1 through 3 respectively. Ingredientsare batched one at a time. Free falling product can be accounted for with the use ofpre-act values (PA1 - PA3). This feature must be enabled before attempting to use.SetpointSelectionFunctionDescriptionP5100.3 Batch 2 or 3 ingredient batching.P5101.-- Targ1 Ingredient 1 target value.P5104.0 Based Select from net or count (quantity).P5105.-- PA 1 Pre-act 1 value (final cutoff for ingredient 1).P5106.1 Learn 1 Learn feature for pre-act 1 enabled.P5107.0 Start 1 Setpoint 1 activation method.P5108.-- Targ 2 Ingredient 2 target value.P5109.-- PA 2 Pre-act 2 value (final cutoff for ingredient 2).P5110.1 Learn 2 Learn feature for pre-act 2 enabled.P5111.0 Start 2 Setpoint 2 activation method.P5116.1 Pause Keypad press invokes pause mode.P5117.-- Targ 3 Ingredient 3 target value.P5118.-- PrAc 3 Pre-act 3 value (final cutoff for ingredient 3).P5119.1 Learn 3 Learn feature for pre-act 3 enabled.P5120.0 Start 3 Setpoint 3 activation method.84Model 350 I.S. and Model 355 I.S. Service Manual
4.19.1 Enter a TargetPressing [TARE] or [ENTER] alone allows access to the subsets. PA1 and PA2 are thesubsets for Targ 1.Model 350 I.S.1. Press [SELECT] until tArG1 is displayed.2. Press [PRINT] until the first digit of the new target is displayed. Press [UNITS]to accept the number displayed. Continue this step until the desired number isentered.Example: Target of 202a. Press [PRINT] four timesDISPLAY READS> 22b. Press [UNITS] to accept the 2 that is displayedDISPLAY READS> 2 .2c. Press [PRINT] onceDISPLAY READS> 202d. Press [TARE] to accept the target weight as 20DISPLAY READS> 203. Press [TARE]. Once the tare key is pressed, it is possible that PA1 will bedisplayed if the pre-act parameter is enabled.3a. If a value is desired, enter it in the same manner as the target weight wasentered above. When the displayed value is correct, press [TARE].3b. If no value is to be entered or PA1 is not displayed, press [TARE] to go to thenext screen.4. Repeat steps 2 and 3 until all targets and pre-acts are entered. Press [TARE]to return to the weigh mode.Model 355 I.S.1. Press [SELECT] until tArG1 is displayed.2. Key in the desired target value with the numeric keys and press [ENTER].3. The PA1 value will be displayed. Key the in value with the numeric keys andpress [ENTER].4. Repeat steps 2 and 3 for tArG2, PA2, tArG3 and PA3.5. Press [SELECT] to select the desired weigh mode parameter.Model 350 I.S. and Model 355 I.S. Service Manual 85
- Page 35 and 36: 3.2.2 Model 355 I.S.Figure 3.3 Mode
- Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
- Page 39 and 40: Battery ChargingTHE BATTERY MUST BE
- Page 41 and 42: 3. Snap the (4) ½ plastic standoff
- Page 43 and 44: Figure 3.12 Fiber-optic Cable Insta
- Page 45 and 46: Install the setpoint or Analog opti
- Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
- Page 49 and 50: 4 ConfigurationThis section covers
- Page 51 and 52: To access the previous parameter1.
- Page 53 and 54: To setup a full scale value (exampl
- Page 55 and 56: 4.5.2 Return to factory default (35
- Page 57 and 58: ParameterNumberDisplayNameP296.00 E
- Page 59 and 60: P115 Stability Delay (Selection)Sel
- Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
- Page 63 and 64: P292 End Character (Key-in)Set the
- Page 65 and 66: P802 Tare and Zero Execution (Selec
- Page 67 and 68: is an 'O' (overload/underload), 'M'
- Page 69 and 70: 4.9 ID Number Entry and PrintingIt
- Page 71 and 72: 4.10.4 Entering ASCII Control Codes
- Page 73 and 74: The default format code for all par
- Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
- Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
- Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
- Page 81 and 82: Pre-act values are entered in terms
- Page 83 and 84: 4. Next the PctHi value will be dis
- Page 85: 3. Press [TARE]. Once the tare key
- Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
- Page 91 and 92: 4.20.3 Start DischargeActivation Me
- Page 93 and 94: 3a. If a value is desired, enter it
- Page 95 and 96: 4.22 Absolute CheckweighThis progra
- Page 97 and 98: 4.23 Target Deviation CheckweighThe
- Page 99 and 100: 4.24 Batch 2The batch 2 program is
- Page 101 and 102: 4.25 Independent Setpoint Operation
- Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
- Page 105 and 106: Bars ON Weight Range (Lower Toleran
- Page 107 and 108: ParameterSettingDisplayedNameDescri
- Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
- Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
- Page 113 and 114: ParameterSettingDisplayedNameDescri
- Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
- Page 117 and 118: 4.28.5 300 Series Command CodesHex
- Page 119 and 120: 5 CalibrationThis chapter covers al
- Page 121 and 122: First Zero Calibration Method (355
- Page 123 and 124: 9. Pause for motion delay.10. Press
- Page 125 and 126: 13. Pause for motion delay.14. Pres
- Page 127 and 128: If the calibration weight value was
- Page 129 and 130: 6 Legal for TradeThe Model 350/355
- Page 131 and 132: 6.4.1 Physical SealThe most common
- Page 133 and 134: 7 TroubleshootingThis chapter conta
- Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
In order for the annunciators to activate, the displayed value must be at least fivegraduations above zero.Fill StatusFast FillDribble Fill (or Single-Speed Fill)Fill Done or PauseAnnunciator StatusSP 1 & SP 2 IlluminatedSP 1 IlluminatedSP 1 & SP 2 OffFill ExampleWith a system set up to fill 55-gallon drums with motor oil, the following settings mightbe used to achieve an accurate final fill weight of 400 lbs.:ParameterSettingActual Cutoff ValueCommentsTarg 1 = 400Desired final weight.Pre-act 1 = 28 400 - 28 = 372.0 Switch to dribble feed at 372.Pre-act 2 = .5 400 - 0.5 = 399.5 Final fill valve closes at 399.5.4.19 BatchThe standard batch program is used for batching up to three separate items.Ingredients 1 through 3 use setpoints and pre-acts 1 through 3 respectively. Ingredientsare batched one at a time. Free falling product can be accounted for with the use ofpre-act values (PA1 - PA3). This feature must be enabled before attempting to use.SetpointSelectionFunctionDescriptionP5100.3 Batch 2 or 3 ingredient batching.P5101.-- Targ1 Ingredient 1 target value.P5104.0 Based Select from net or count (quantity).P5105.-- PA 1 Pre-act 1 value (final cutoff for ingredient 1).P5106.1 Learn 1 Learn feature for pre-act 1 enabled.P5107.0 Start 1 Setpoint 1 activation method.P5108.-- Targ 2 Ingredient 2 target value.P5109.-- PA 2 Pre-act 2 value (final cutoff for ingredient 2).P5110.1 Learn 2 Learn feature for pre-act 2 enabled.P5111.0 Start 2 Setpoint 2 activation method.P5116.1 Pause Keypad press invokes pause mode.P5117.-- Targ 3 Ingredient 3 target value.P5118.-- PrAc 3 Pre-act 3 value (final cutoff for ingredient 3).P5119.1 Learn 3 Learn feature for pre-act 3 enabled.P5120.0 Start 3 Setpoint 3 activation method.84Model 350 I.S. and Model 355 I.S. <strong>Service</strong> <strong>Manual</strong>