GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

4.10.1 Writing A Custom Transmit ASCII Text FileAny text editor may be used to construct a custom transmit (Notepad, Wordpad,Communication Plus, etc.), but you must save the custom transmit as a text (.txt) file.Instructions can also be sent keystroke by keystroke from a communications program.To do so, ignore the Model 350/355 I.S. display and enter the characters in the correctorder. Figure 4.1 shows a custom transmit written in Wordpad.4.10.2 Access Setup and Clearing Existing Custom TransmitEvery custom transmit file must start with:1999%s%s%z%p%u%e%c%eThis accesses the Setup Mode at the end of the existing transmit and then clears thetransmit so that a new one may be entered.Figure 4.1 Custom Transmit File4.10.3 Entering ASCII TextASCII text is defined as printable characters, including alpha-numeric as well aspunctuation and symbols. See Table 4.1 for a complete listing of ASCII characters.ASCII text can be entered directly into a custom transmit with a %e (enter command).For example, Joe's Fertilizer Plant%e.68Model 350 I.S. and Model 355 I.S. Service Manual
4.10.4 Entering ASCII Control CodesSome ASCII characters are known as control codes, non-printable characters thatinstruct a printing device to perform certain functions. For example, a carriage return forces a printer to move the print head to the left-most position of the current line.A line feed forces the print head to move down one line. Enter control codes witha decimal point, a 3-digit ASCII code, and a %e. For example, .013%e.hex CHAR dec hex CHAR dec hex CHAR dec hex CHAR dec hex CHAR dec00 NUL 000 1A SUB 026 34 4 052 NE N 078 68 h 10401 SOH 001 1B ESC 027 35 5 053 4F O 079 69 i 10502 STX 002 1C FS 028 36 6 054 50 P 080 6A j 10603 ETX 003 1D GS 029 37 7 055 51 Q 081 6B k 10704 EOT 004 1E RS 030 38 8 056 52 R 082 6C l 10805 ENQ 005 1F US 031 39 9 057 53 S 083 6D m 10906 ACK 006 20 SP 032 3A : 058 54 T 084 6E n 11007 BEL 007 21 ! 033 3B ; 059 55 U 085 6F o 11108 BS 008 22 " 034 3C < 060 56 V 086 70 p 11209 HT 009 23 # 035 3D = 061 57 W 087 71 q 1130A LF 010 24 $ 036 3E > 062 58 X 088 72 r 1140B VT 011 25 % 037 3F ? 063 59 Y 089 73 s 1150C FF 012 26 & 038 40 @ 064 5A Z 090 74 t 1160D CR 013 27 ' 039 41 A 065 5B [ 091 75 u 1170E SO 014 28 ( 040 42 B 066 5C \ 092 76 v 1180F SI 015 29 ) 041 43 C 067 5D ] 093 77 w 11910 DLE 016 2A * 042 44 D 068 5E ^ 094 78 x 12011 DC1 017 2B + 043 45 E 069 5F _ 095 79 y 12112 DC2 018 2C ' 044 46 F 070 60 ` 096 7A z 12213 DC3 019 2D - 045 47 G 071 61 a 097 7B { 12314 DC4 020 2E . 046 48 H 072 62 b 098 7C | 12415 NAK 021 2F / 047 49 I 073 63 c 099 7D } 12516 SYN 022 30 0 048 4A J 074 64 d 100 7E ~ 12617 ETB 023 31 1 049 4B K 075 65 e 101 7F DEL 12718 CAN 024 32 2 050 4C L 076 66 f 10219 EM 025 33 3 051 4D M 077 67 g 103Table 4.1 ASCII / Hexadecimal Conversion ChartMost printers require a carriage return (.013) and/or a line feed (.010) to printpreceding data and avoid leaving data in the printer buffer.Model 350 I.S. and Model 355 I.S. Service Manual 69
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20: TerminalEntity / Nonincendive Field
Page 21 and 22: GasApprovalTemperatureRangeT class
Page 23 and 24: 2.5 Standard FunctionsThe Model 350
Page 25 and 26: Safe Area OptionsBattery ChargerFib
Page 27 and 28: 2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30: Key Press Weigh Mode Count Mode Set
Page 31 and 32: 2.11 Weigh Mode FunctionsThe Model
Page 33 and 34: 3 InstallationThe Model 350/355 I.S
Page 35 and 36: 3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
Page 39 and 40: Battery ChargingTHE BATTERY MUST BE
Page 41 and 42: 3. Snap the (4) ½ plastic standoff
Page 43 and 44: Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46: Install the setpoint or Analog opti
Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
Page 49 and 50: 4 ConfigurationThis section covers
Page 51 and 52: To access the previous parameter1.
Page 53 and 54: To setup a full scale value (exampl
Page 55 and 56: 4.5.2 Return to factory default (35
Page 57 and 58: ParameterNumberDisplayNameP296.00 E
Page 59 and 60: P115 Stability Delay (Selection)Sel
Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64: P292 End Character (Key-in)Set the
Page 65 and 66: P802 Tare and Zero Execution (Selec
Page 67 and 68: is an 'O' (overload/underload), 'M'
Page 69: 4.9 ID Number Entry and PrintingIt
Page 73 and 74: The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113 and 114: ParameterSettingDisplayedNameDescri
Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122:
First Zero Calibration Method (355
Page 123 and 124:
9. Pause for motion delay.10. Press
Page 125 and 126:
13. Pause for motion delay.14. Pres
Page 127 and 128:
If the calibration weight value was
Page 129 and 130:
6 Legal for TradeThe Model 350/355
Page 131 and 132:
6.4.1 Physical SealThe most common
Page 133 and 134:
7 TroubleshootingThis chapter conta
Page 135 and 136:
7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138:
Table 7.1 Information Parameters.Pa
Page 139 and 140:
8 MaintenanceThe mainboard, keypad
Page 141 and 142:
5. Connect the keypad cable to the
Page 143 and 144:
9 Label DrawingsReference for Model
Page 145 and 146:
9.5 355 I.S. Generic Rear Label (5
Page 147 and 148:
Appendix A: Model 350 I.S. and Mode
Page 149 and 150:
AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152:
AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154:
Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156:
Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?