GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

ParameterNumberDisplayNameDefault ValueValid Range/ ChoicesP5004.00 Chec Auto Auto / Start(Toggle)P5010.00 SPAnn Enable Enable / Disable(Toggle)P5011.00 SPBar Disable Enable / Disable(Toggle)P5012.00 BarPc 50% 0 - 100(Key In)P5100.00 SetPt None None - Checb(9 Selections)ParameterDescriptionPageRestart Mode 63Setpoint Annunciators 63Bargraph Display 64Bargraph Scaling 64Setpoint Operation 644.7 Parameter Map DetailsP110 Full Scale Value (Key in)Denotes the full scale capacity. This value should not exceed the rated capacity of theweighing device.P111 Division Size (Selection)Indicates the count-by and decimal point. Pressing [ZERO] + [TARE] (Model 350 I.S.)or [CLR] (Model 355 I.S.) will automatically select the choice closest to 10,000 divisionswithout exceeding 10,000 divisions.P112 Zero Track Aperture (Selection)Set in terms of number of divisions. Zero tracking eliminates small weight deviations ator near zero. Weight deviations within the selected window that have been stable formore than one second are tracked off, maintaining a gross or net zero condition.The sum of weight values zeroed with auto zero tracking and [ZERO] cannot exceedthe allowable zero range (P118).To determine the proper setting in a counting application, divide the weight of thesmallest product counted by the division size (P111). Zero Track should be set to 0 (off)for most setpoint filling operations. This prevents tracking off any product trickle at thestart of a fill process.P114 Stability (Selection)Stability is defined as weight fluctuations within an aperture that can be regarded asbeing a stable weight. Deviations outside this aperture are considered motion, and themotion annunciator on the front panel will light accordingly. Once the scale settleswithin the stability aperture, the indicator will wait for a period of time specified by themotion delay (P115) before the indicator is considered stable.Print operations configured as motion delayed (P114) will not send the specified datauntil the weight reflects a stable reading as designated by this setting. Certain setpointoperations are also considered motion delayed and will not change states until a nomotioncondition exists.56Model 350 I.S. and Model 355 I.S. Service Manual
P115 Stability Delay (Selection)Selects the stability (motion) time delay to a resolution of 0.1 seconds. For example, anentry of 25 will be accepted as 2.5 seconds.P116 Filter (Selection)Sets the indicator response time in terms of seconds. Filtering determines how quicklythe indicator will respond to changing input signals. A low filter setting speeds theresponse, a higher filter setting will 'dampen' the response.Filtering is used to filter out weight fluctuations caused by outside sources, such asvibrations or air currents.P117 Rate (Selection)Specifies how often the display is updated with new data and the rate of continuoustransmits (if P210 or P230 are enabled). For example, if 0.05 is selected, the controllerwill write data to the display and send continuous transmits 20 times a second.Selections from 0.05 to 20.0 seconds are available. The actual rate may be less than(P117). The actual rate depends on the indicator speed (P60090), the size and numberof transmits (P1000, P2000, P210, and P230), and COM ports' speed (if echo (P290)is enabled or continuous transmits are enabled).P118 Zero Range (Selection)Specifies how many divisions can be zeroed in terms of a percentage of full scale(P110). The sum of weight values zeroed through the [ZERO] key and auto zerotracking cannot exceed this range.A zero range of 5% is commonly used with large tank scales to avoid accidental zeroingof a full or partially full tank.P119 Multi-Point Linearization (Toggle)Enable the five-point linearization feature used during load cell calibration.P150 Units (Toggle)Set default units to 'lb' or 'kg'. The indicator must use the default units during calibrationprocedures. The default units are the displayed units upon indicator power-up.P151 Units Button (Toggle)When enabled, this parameter will allow the [UNITS] key to toggle the units between lband kg (1000g). When disabled, the indicator will show only the calibration units asdetermined by P150.P152 Third Unit (Selection)This parameter will allow the choice of three additional units (ounces, grams or lb oz)that may be accessed with the [UNITS] key. Only one unit will be available at a time.The third unit can only be selected if P151 is enabled. The additional unit will beidentified by an annunciator on the display. This unit selection is not legal for trade.Model 350 I.S. and Model 355 I.S. Service Manual 57
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8: 1 General Information and Warnings1
Page 9 and 10: 1.3.3 Safe Handling of Equipment wi
Page 11 and 12: 1.8 FCC and EMC Declarations of Com
Page 13 and 14: 2 IntroductionThis section explains
Page 15 and 16: Note: Electrical apparatus Approved
Page 17 and 18: Ca or Co - the maximum capacitance
Page 19 and 20: TerminalEntity / Nonincendive Field
Page 21 and 22: GasApprovalTemperatureRangeT class
Page 23 and 24: 2.5 Standard FunctionsThe Model 350
Page 25 and 26: Safe Area OptionsBattery ChargerFib
Page 27 and 28: 2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30: Key Press Weigh Mode Count Mode Set
Page 31 and 32: 2.11 Weigh Mode FunctionsThe Model
Page 33 and 34: 3 InstallationThe Model 350/355 I.S
Page 35 and 36: 3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
Page 39 and 40: Battery ChargingTHE BATTERY MUST BE
Page 41 and 42: 3. Snap the (4) ½ plastic standoff
Page 43 and 44: Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46: Install the setpoint or Analog opti
Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
Page 49 and 50: 4 ConfigurationThis section covers
Page 51 and 52: To access the previous parameter1.
Page 53 and 54: To setup a full scale value (exampl
Page 55 and 56: 4.5.2 Return to factory default (35
Page 57: ParameterNumberDisplayNameP296.00 E
Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64: P292 End Character (Key-in)Set the
Page 65 and 66: P802 Tare and Zero Execution (Selec
Page 67 and 68: is an 'O' (overload/underload), 'M'
Page 69 and 70: 4.9 ID Number Entry and PrintingIt
Page 71 and 72: 4.10.4 Entering ASCII Control Codes
Page 73 and 74: The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110:
4.27.2 Analog Output ExampleAnalogP
Page 111 and 112:
4.28.2 Setup Master IndicatorSet th
Page 113 and 114:
ParameterSettingDisplayedNameDescri
Page 115 and 116:
Custom Transmit :1. [.002] [ENTER]
Page 117 and 118:
4.28.5 300 Series Command CodesHex
Page 119 and 120:
5 CalibrationThis chapter covers al
Page 121 and 122:
First Zero Calibration Method (355
Page 123 and 124:
9. Pause for motion delay.10. Press
Page 125 and 126:
13. Pause for motion delay.14. Pres
Page 127 and 128:
If the calibration weight value was
Page 129 and 130:
6 Legal for TradeThe Model 350/355
Page 131 and 132:
6.4.1 Physical SealThe most common
Page 133 and 134:
7 TroubleshootingThis chapter conta
Page 135 and 136:
7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138:
Table 7.1 Information Parameters.Pa
Page 139 and 140:
8 MaintenanceThe mainboard, keypad
Page 141 and 142:
5. Connect the keypad cable to the
Page 143 and 144:
9 Label DrawingsReference for Model
Page 145 and 146:
9.5 355 I.S. Generic Rear Label (5
Page 147 and 148:
Appendix A: Model 350 I.S. and Mode
Page 149 and 150:
AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152:
AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154:
Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156:
Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?