GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

Figure 3.13 Fiber-optic Cable Installation (HCS Cable)3.8.3 Safe Area Setpoint Option InstallationUsing one of the software setpoint configurations (see Setpoint Setup on page 77) inconjunction with the setpoint option board gives the Safe Area indicator the ability todirectly control external devices such as valves, relays, actuators, etc.There are up to three setpoint outputs available. The activation and deactivation iscontrolled by the setpoint configuration. The outputs are capable of driving up to oneAmp at 20-280VAC & 2 Amp at 3-60VDC. The solid state relays are normally open(N.O.) contacts.See Setpoint Setup on page 77 for setpoint software configuration details.The Safe Area Hub contains components which could be damaged byElectrostatic Discharge (ESD) if serviced improperly. Use proper ESDprecautions (wear a wrist strap connected to ground, use grounded workstations, etc.) when opening the enclosure.Never connect or disconnect option board cables while the indicator ispowered. Doing so may result in circuit board damage.42Model 350 I.S. and Model 355 I.S. Service Manual
Install the setpoint or Analog option in a safe area hub1. Open the indicator.2. Remove the eight screws from the back of the unit.3. Locate the three studs and one thru-hole on the main board that the optionmounting bracket will be attached to. See Figure 3.14. Remove the nuts fromthe three studs on the main board.3a. It may help to position the option mounting bracket over the main board tolocate the three studs and one thru-hole.4. Install the nylon stand-off supplied with the option bracket kit into the thru-holeon the option bracket. See Figure 3.14.4a. The thru-hole on the option bracket is the irregular flanged section (a smallerhole than the others on the bracket).5. Install the three hex stand-offs onto the studs on the main board.6. Tighten the stand-offs gently with a 6 mm hex nut driver.6a. If this is the first option card, attach the loose end of the cable to the serial I/Oconnector (J3) on the main board. Let the card gently hang over to the outsideof the enclosure until mounting. J3 is a 10-pin polarized connector.6b. This step is not necessary if this is the second card installed.7. Position the nylon stand-off (attached to the bracket) into the hole on the mainboard while routing the threads of the other hex stand-offs through the holeson the bracket, while pressing down over the nylon stand-off until it snaps intoplace.8. Line-up the three other hex stand-offs into the bracket thru-holes first beforesecuring the nylon stand-off into the main board thru-hole.9. Secure the bracket into position with the hex nuts supplied with the kit. Do notover tighten.10. Place one set (four pieces) of the nylon sleeve type stand-offs onto the fourstuds of the option bracket. Place the Setpoint Control Module, componentside up, onto the nylon sleeve stand-offs. Install four hex nuts and securegently.11. Select the four studs closest to the (J3) connector of the main board to add thefour sleeve stand-offs. Be sure the cable is already attached to (J3) on themain board before installing the card. Also be sure the cable is attached to theright-most connector (J3) (as viewed from the component side of the optionboard). The second connector (J1) is for 'daisy-chaining' another option card.The additional mounting hardware is supplied with the option bracket kit. Thishardware should be saved for future use if not being used.12. Route the analog cable through the available strain-relief. Make sure toconnect cable conductors to the proper terminals before closing the unit.13. Reinstall the back cover. Tighten the eight screws securely to create a goodseal. Be sure to avoid pinching the cable between the housing halves.Model 350 I.S. and Model 355 I.S. Service Manual 43
Page 1 and 2: Model 350I.S. and Model 355I.S.Inst
Page 3 and 4: Table of ContentsChapter 1 General
Page 5 and 6: Start Fill ........................
Page 7 and 8: 1 General Information and Warnings1
Page 9 and 10: 1.3.3 Safe Handling of Equipment wi
Page 11 and 12: 1.8 FCC and EMC Declarations of Com
Page 13 and 14: 2 IntroductionThis section explains
Page 15 and 16: Note: Electrical apparatus Approved
Page 17 and 18: Ca or Co - the maximum capacitance
Page 19 and 20: TerminalEntity / Nonincendive Field
Page 21 and 22: GasApprovalTemperatureRangeT class
Page 23 and 24: 2.5 Standard FunctionsThe Model 350
Page 25 and 26: Safe Area OptionsBattery ChargerFib
Page 27 and 28: 2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30: Key Press Weigh Mode Count Mode Set
Page 31 and 32: 2.11 Weigh Mode FunctionsThe Model
Page 33 and 34: 3 InstallationThe Model 350/355 I.S
Page 35 and 36: 3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
Page 39 and 40: Battery ChargingTHE BATTERY MUST BE
Page 41 and 42: 3. Snap the (4) ½ plastic standoff
Page 43: Figure 3.12 Fiber-optic Cable Insta
Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
Page 49 and 50: 4 ConfigurationThis section covers
Page 51 and 52: To access the previous parameter1.
Page 53 and 54: To setup a full scale value (exampl
Page 55 and 56: 4.5.2 Return to factory default (35
Page 57 and 58: ParameterNumberDisplayNameP296.00 E
Page 59 and 60: P115 Stability Delay (Selection)Sel
Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64: P292 End Character (Key-in)Set the
Page 65 and 66: P802 Tare and Zero Execution (Selec
Page 67 and 68: is an 'O' (overload/underload), 'M'
Page 69 and 70: 4.9 ID Number Entry and PrintingIt
Page 71 and 72: 4.10.4 Entering ASCII Control Codes
Page 73 and 74: The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96:
4.22 Absolute CheckweighThis progra
Page 97 and 98:
4.23 Target Deviation CheckweighThe
Page 99 and 100:
4.24 Batch 2The batch 2 program is
Page 101 and 102:
4.25 Independent Setpoint Operation
Page 103 and 104:
4.25.3 ExampleSetup a continuous-cy
Page 105 and 106:
Bars ON Weight Range (Lower Toleran
Page 107 and 108:
ParameterSettingDisplayedNameDescri
Page 109 and 110:
4.27.2 Analog Output ExampleAnalogP
Page 111 and 112:
4.28.2 Setup Master IndicatorSet th
Page 113 and 114:
ParameterSettingDisplayedNameDescri
Page 115 and 116:
Custom Transmit :1. [.002] [ENTER]
Page 117 and 118:
4.28.5 300 Series Command CodesHex
Page 119 and 120:
5 CalibrationThis chapter covers al
Page 121 and 122:
First Zero Calibration Method (355
Page 123 and 124:
9. Pause for motion delay.10. Press
Page 125 and 126:
13. Pause for motion delay.14. Pres
Page 127 and 128:
If the calibration weight value was
Page 129 and 130:
6 Legal for TradeThe Model 350/355
Page 131 and 132:
6.4.1 Physical SealThe most common
Page 133 and 134:
7 TroubleshootingThis chapter conta
Page 135 and 136:
7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138:
Table 7.1 Information Parameters.Pa
Page 139 and 140:
8 MaintenanceThe mainboard, keypad
Page 141 and 142:
5. Connect the keypad cable to the
Page 143 and 144:
9 Label DrawingsReference for Model
Page 145 and 146:
9.5 355 I.S. Generic Rear Label (5
Page 147 and 148:
Appendix A: Model 350 I.S. and Mode
Page 149 and 150:
AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152:
AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154:
Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156:
Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?