GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

The AC to DC supply has a conduit fitting on the bottom where the power cable isattached to the unit. This fitting is 1" in diameter and has a 1/2" thread.Figure 3.9 AC to DC Power Supply Outline Drawing3.7.3 AC To DC Power Supply Extension CableThe extension cable comes in either 25' or 50' length. This cable is used for mountingthe AC to DC converter away from the indicator. Fifty feet is the maximum allowed frompower supply to indicator.3.7.4 5 Volt And 8 Volt ExcitationTwo versions of excitation are available for the Model 350 I.S. and Model 355 I.S. The5-volt excitation consumes less power than the 8-volt excitation module. The 5-voltexcitation is standard on the main board. The 8-volt excitation is on a separate boardwhich is installed by the factory. The 5-volt excitation is +5V to 0V. The 8-volt excitationis +5V to -3V.3.7.5 Fiber-Optic InterfaceIt is possible to use setpoints and analog output by interfacing the hazardous areaindicator (350 I.S. or 355 I.S.) with any 350 Series stainless steel indicator in the safearea. A fiber-optic option kit (24350B-420B0) will be used for both indicators andinstalled in the control and hub indicators. Refer to the installation instructions below.Fiber-Optic Board Installation1. Remove the rear panel screws of the Model 350/355 I.S.2. Locate the fiber-optic board connector (J6) on the Model 350/355 I.S. mainboard.38Model 350 I.S. and Model 355 I.S. Service Manual
3. Snap the (4) ½ plastic standoffs provided with the fiber-optic board into theholes surrounding the J6 connector. This area is outlined.4. Place the fiber-optic board on the standoffs but do not press onto thestandoffs.5. Line up the J1 connector on the back of the fiber-optic board with J6 on theModel 350/355 I.S. main board.6. Press the fiber-optic board onto the plastic standoffs. Refer to Figure 3.10.7. Remove the rubber plugs from the J2 and J3 connectors on the fiber opticboard.8. Follow the instructions on page 38 for installing the fiber-optic cable to thefiber-optic board.Figure 3.10 Fiber-optic Board Installation (Model 350 I.S. / 355 I.S.)3.8 Safe Area Options3.8.1 Fiber-Optic InterfaceFor detailed instructions on installing the fiber-optic interface option refer to page 38Plastic Fiber-Optic Cable Installation and TerminationThe plastic fiber-optic cable is an inexpensive way to connect an intrinsically safeindicator to a safe area hub indicator. The cable allows a distance of 200 feet maximum.1. Unscrew cap from the strain relief next to the loadcell strain relief.2. Remove rubber grommet from inside the strain reliefModel 350 I.S. and Model 355 I.S. Service Manual 39
Page 1 and 2: Model 350I.S. and Model 355I.S.Inst
Page 3 and 4: Table of ContentsChapter 1 General
Page 5 and 6: Start Fill ........................
Page 7 and 8: 1 General Information and Warnings1
Page 9 and 10: 1.3.3 Safe Handling of Equipment wi
Page 11 and 12: 1.8 FCC and EMC Declarations of Com
Page 13 and 14: 2 IntroductionThis section explains
Page 15 and 16: Note: Electrical apparatus Approved
Page 17 and 18: Ca or Co - the maximum capacitance
Page 19 and 20: TerminalEntity / Nonincendive Field
Page 21 and 22: GasApprovalTemperatureRangeT class
Page 23 and 24: 2.5 Standard FunctionsThe Model 350
Page 25 and 26: Safe Area OptionsBattery ChargerFib
Page 27 and 28: 2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30: Key Press Weigh Mode Count Mode Set
Page 31 and 32: 2.11 Weigh Mode FunctionsThe Model
Page 33 and 34: 3 InstallationThe Model 350/355 I.S
Page 35 and 36: 3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38: 3.5 Remote Key ConnectionsThe Model
Page 39: Battery ChargingTHE BATTERY MUST BE
Page 43 and 44: Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46: Install the setpoint or Analog opti
Page 47 and 48: 3.8.5 Safe Area Analog Option Insta
Page 49 and 50: 4 ConfigurationThis section covers
Page 51 and 52: To access the previous parameter1.
Page 53 and 54: To setup a full scale value (exampl
Page 55 and 56: 4.5.2 Return to factory default (35
Page 57 and 58: ParameterNumberDisplayNameP296.00 E
Page 59 and 60: P115 Stability Delay (Selection)Sel
Page 61 and 62: P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64: P292 End Character (Key-in)Set the
Page 65 and 66: P802 Tare and Zero Execution (Selec
Page 67 and 68: is an 'O' (overload/underload), 'M'
Page 69 and 70: 4.9 ID Number Entry and PrintingIt
Page 71 and 72: 4.10.4 Entering ASCII Control Codes
Page 73 and 74: The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92:
4.20.3 Start DischargeActivation Me
Page 93 and 94:
3a. If a value is desired, enter it
Page 95 and 96:
4.22 Absolute CheckweighThis progra
Page 97 and 98:
4.23 Target Deviation CheckweighThe
Page 99 and 100:
4.24 Batch 2The batch 2 program is
Page 101 and 102:
4.25 Independent Setpoint Operation
Page 103 and 104:
4.25.3 ExampleSetup a continuous-cy
Page 105 and 106:
Bars ON Weight Range (Lower Toleran
Page 107 and 108:
ParameterSettingDisplayedNameDescri
Page 109 and 110:
4.27.2 Analog Output ExampleAnalogP
Page 111 and 112:
4.28.2 Setup Master IndicatorSet th
Page 113 and 114:
ParameterSettingDisplayedNameDescri
Page 115 and 116:
Custom Transmit :1. [.002] [ENTER]
Page 117 and 118:
4.28.5 300 Series Command CodesHex
Page 119 and 120:
5 CalibrationThis chapter covers al
Page 121 and 122:
First Zero Calibration Method (355
Page 123 and 124:
9. Pause for motion delay.10. Press
Page 125 and 126:
13. Pause for motion delay.14. Pres
Page 127 and 128:
If the calibration weight value was
Page 129 and 130:
6 Legal for TradeThe Model 350/355
Page 131 and 132:
6.4.1 Physical SealThe most common
Page 133 and 134:
7 TroubleshootingThis chapter conta
Page 135 and 136:
7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138:
Table 7.1 Information Parameters.Pa
Page 139 and 140:
8 MaintenanceThe mainboard, keypad
Page 141 and 142:
5. Connect the keypad cable to the
Page 143 and 144:
9 Label DrawingsReference for Model
Page 145 and 146:
9.5 355 I.S. Generic Rear Label (5
Page 147 and 148:
Appendix A: Model 350 I.S. and Mode
Page 149 and 150:
AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152:
AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154:
Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156:
Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?