GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

9.3 350 I.S. Generic Rear Label (5 Volt Excitation)Control Drawings: 41533 and AWT35-5003899.4 350 I.S. Generic Rear Label (8 Volt Excitation)Control Drawing: 41533142Model 350 I.S. and Model 355 I.S. Service Manual
9.5 355 I.S. Generic Rear Label (5 Volt Excitation)Control Drawings: 41533 and AWT35-5003899.6 355 I.S. Generic Rear Label (8 Volt Excitation)Control Drawing: 41533Model 350 I.S. and Model 355 I.S. Service Manual 143
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20:
TerminalEntity / Nonincendive Field
Page 21 and 22:
GasApprovalTemperatureRangeT class
Page 23 and 24:
2.5 Standard FunctionsThe Model 350
Page 25 and 26:
Safe Area OptionsBattery ChargerFib
Page 27 and 28:
2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30:
Key Press Weigh Mode Count Mode Set
Page 31 and 32:
2.11 Weigh Mode FunctionsThe Model
Page 33 and 34:
3 InstallationThe Model 350/355 I.S
Page 35 and 36:
3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38:
3.5 Remote Key ConnectionsThe Model
Page 39 and 40:
Battery ChargingTHE BATTERY MUST BE
Page 41 and 42:
3. Snap the (4) ½ plastic standoff
Page 43 and 44:
Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46:
Install the setpoint or Analog opti
Page 47 and 48:
3.8.5 Safe Area Analog Option Insta
Page 49 and 50:
4 ConfigurationThis section covers
Page 51 and 52:
To access the previous parameter1.
Page 53 and 54:
To setup a full scale value (exampl
Page 55 and 56:
4.5.2 Return to factory default (35
Page 57 and 58:
ParameterNumberDisplayNameP296.00 E
Page 59 and 60:
P115 Stability Delay (Selection)Sel
Page 61 and 62:
P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64:
P292 End Character (Key-in)Set the
Page 65 and 66:
P802 Tare and Zero Execution (Selec
Page 67 and 68:
is an 'O' (overload/underload), 'M'
Page 69 and 70:
4.9 ID Number Entry and PrintingIt
Page 71 and 72:
4.10.4 Entering ASCII Control Codes
Page 73 and 74:
The default format code for all par
Page 75 and 76:
4.12.2 Model 355 I.S.To sample usin
Page 77 and 78:
4.14 Remote Key ConfigurationThe Mo
Page 79 and 80:
4.16 Setpoint SetupThe Model 350/35
Page 81 and 82:
Pre-act values are entered in terms
Page 83 and 84:
4. Next the PctHi value will be dis
Page 85 and 86:
3. Press [TARE]. Once the tare key
Page 87 and 88:
4.19.1 Enter a TargetPressing [TARE
Page 89 and 90:
ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92:
4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113 and 114: ParameterSettingDisplayedNameDescri
Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122: First Zero Calibration Method (355
Page 123 and 124: 9. Pause for motion delay.10. Press
Page 125 and 126: 13. Pause for motion delay.14. Pres
Page 127 and 128: If the calibration weight value was
Page 129 and 130: 6 Legal for TradeThe Model 350/355
Page 131 and 132: 6.4.1 Physical SealThe most common
Page 133 and 134: 7 TroubleshootingThis chapter conta
Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138: Table 7.1 Information Parameters.Pa
Page 139 and 140: 8 MaintenanceThe mainboard, keypad
Page 141 and 142: 5. Connect the keypad cable to the
Page 143: 9 Label DrawingsReference for Model
Page 147 and 148: Appendix A: Model 350 I.S. and Mode
Page 149 and 150: AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152: AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154: Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156: Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?