GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

7.1.2 Setup Mode ErrorsCodeBad ~ Code!Unit ~ SealdUnit3-NtepCode 49.Entry ~ ErrorNeed ~ EntryOut of ~RangeCan't ~ Set!ResGT~ 260E3Code 35.ResGT~ 25E3ResLT ~ 100!ResLT ~ 1 !!SPtxx ~ ErrorPrtcl ~ ErrorReboot! ~ tochang baudAn incorrect access code was entered.DescriptionAccess to the Setup or Calibration Mode was denied. Check the internal "YES/NO" program jumper.Parameter 440 (NTEP) is enabled and parameter 152 (third unit) is set to an additional unit. The third unitis not NTEP approved.An invalid entry was made.A numeric value was required before pressing [TARE].The entered value exceeded the allowable range.Attempt to change a parameter that does not allow an entry.The number of divisions exceeds 260000 (see P110, P111).The number of divisions exceeds 25000 (see P110, P111).The number of divisions is less than 100 (see P110, P111).Number of divisions is less than one (see P110, P111).A conflict occurred with a setpoint value entry (example: target entry is less than preact).The digits 'xx'represent the last two digits of the setpoint parameter in error (example: SPt 5 ~ Error indicates a conflictP5105, preact 1).Existing protocol is invalid.The following are not allowed:- P201 = 7 data bits, P202 = no parity, P203 = 1 stop bit- P201 = 8 data bits, P202 = even parity, P203 = 2 stop bits- P201 = 8 data bits, P202 = odd parity, P 203 = 2 stop bitsThe current CPU speed at P60090 is low for the chosen baud rate.7.1.3 Hardware ErrorsCodeDescriptionCode00A FRAM problem detected during power-up.A-D ~ Bad!OrProblem with A/D chip detected. Disconnect any options installed and re-power the unit. Options areconnected to the same serial lines as the A/D so they may prevent it from working properly.Code17Deflt ~ A-D Bad A/D calibration values. Recalibrate A/D (see A/D Calibration Procedure on page 136).Re- ~ Boot! FRAM data could not be read. Attempting power-up reset.Chec ~ E2FRAM data error.Deflt ~ Setup An error occurred when reading setup data from the FRAM during power-up. All parameters are set to factorydefault.Ch.XXXXA checksum error occurred during power-up.All annunciators are lit. The FRAM integrity test failed or isimproperly seated.E2 ~ Full!The FRAM setup exceeds the memory capacity.E2 rd Error Error reading EEProm. Send into Avery Weigh-TronixNoSpc ~ Free! The current setup exceeds the setup RAM capacity.132Model 350 I.S. and Model 355 I.S. Service Manual
7.1.4 Calibration ErrorsCodeF.S. ~TooHiF.S. ~ TooLoAdd ~ Load!ReCal ~ ???Entry ~ ErrorDescriptionThe entered calibration weight will result in an over-capacity condition at full scale. Verify that the full scale(P110) and calibration weight value are correct.The entered calibration weight will result in a full scale input signal less than the minimum allowed. Verify thatthe full scale (P110) and entered weight value are correct.The calibration weight is less than 0.1% of capacity. More weight is required.Repeat the cal. procedure for accuracy. This prompt appears when the calibration weight is less than 5% ofcapacity, or when the A/D coarse gain is adjusted.An invalid entry was made.7.1.5 Communication ErrorsCodePar-ErBuf-ErBit-ErTrans~Hold1Trans~Hold2Error~BaudXDescriptionThe selected parity (P202) does not match that of the connected device.The receive buffers capacity was exceeded. This indicates a handshaking problem. Check P204 and verifyproper communication port connections.The stop bit of a received character did not occur when expected. Verify that protocol (P200 - P204) matchesthat of the connected device.Data transmission is inhibited due to a deasserted handshake on communication port 1. Press [ZERO] or[CLR] to abort transmission. Check P204. If in a Control and Hub configuration, press [ZERO] or [CLR] threetimes to clear the error.Data transmission is inhibited due to a deasserted handshake on communication port 2. Press [ZERO] or[CLR] to abort transmission. Check P204. Check P204. If in a Control and Hub configuration, press [ZERO] or[CLR] three times to clear the error.The X being either comm port 1 or comm. port 2. The baud rate selected is too high for the microprocessorrate. Either set the baud rate lower or change the microprocessor rate at P60090 higher.7.1.6 Miscellaneous ErrorsCodeT.X.YYYYDescriptionIf catastrophic errors occur in the software, a trap error may occur and freeze the display with addressinformation. (X = bank number and YYYY = the address of the trap error. Press any key five seconds afterviewing message to reboot the unit).7.2 Viewing Setup ParametersWhile troubleshooting it may be helpful to view the setup parameter selections. Thiscan be done using the procedure below (even with the internal program jumper in the"NO" position). Note that accessing the Setup Mode in this manner will not permitparameter changes.Model 350 I.S. and Model 355 I.S. Service Manual 133
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20:
TerminalEntity / Nonincendive Field
Page 21 and 22:
GasApprovalTemperatureRangeT class
Page 23 and 24:
2.5 Standard FunctionsThe Model 350
Page 25 and 26:
Safe Area OptionsBattery ChargerFib
Page 27 and 28:
2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30:
Key Press Weigh Mode Count Mode Set
Page 31 and 32:
2.11 Weigh Mode FunctionsThe Model
Page 33 and 34:
3 InstallationThe Model 350/355 I.S
Page 35 and 36:
3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38:
3.5 Remote Key ConnectionsThe Model
Page 39 and 40:
Battery ChargingTHE BATTERY MUST BE
Page 41 and 42:
3. Snap the (4) ½ plastic standoff
Page 43 and 44:
Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46:
Install the setpoint or Analog opti
Page 47 and 48:
3.8.5 Safe Area Analog Option Insta
Page 49 and 50:
4 ConfigurationThis section covers
Page 51 and 52:
To access the previous parameter1.
Page 53 and 54:
To setup a full scale value (exampl
Page 55 and 56:
4.5.2 Return to factory default (35
Page 57 and 58:
ParameterNumberDisplayNameP296.00 E
Page 59 and 60:
P115 Stability Delay (Selection)Sel
Page 61 and 62:
P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64:
P292 End Character (Key-in)Set the
Page 65 and 66:
P802 Tare and Zero Execution (Selec
Page 67 and 68:
is an 'O' (overload/underload), 'M'
Page 69 and 70:
4.9 ID Number Entry and PrintingIt
Page 71 and 72:
4.10.4 Entering ASCII Control Codes
Page 73 and 74:
The default format code for all par
Page 75 and 76:
4.12.2 Model 355 I.S.To sample usin
Page 77 and 78:
4.14 Remote Key ConfigurationThe Mo
Page 79 and 80:
4.16 Setpoint SetupThe Model 350/35
Page 81 and 82:
Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113 and 114: ParameterSettingDisplayedNameDescri
Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122: First Zero Calibration Method (355
Page 123 and 124: 9. Pause for motion delay.10. Press
Page 125 and 126: 13. Pause for motion delay.14. Pres
Page 127 and 128: If the calibration weight value was
Page 129 and 130: 6 Legal for TradeThe Model 350/355
Page 131 and 132: 6.4.1 Physical SealThe most common
Page 133: 7 TroubleshootingThis chapter conta
Page 137 and 138: Table 7.1 Information Parameters.Pa
Page 139 and 140: 8 MaintenanceThe mainboard, keypad
Page 141 and 142: 5. Connect the keypad cable to the
Page 143 and 144: 9 Label DrawingsReference for Model
Page 145 and 146: 9.5 355 I.S. Generic Rear Label (5
Page 147 and 148: Appendix A: Model 350 I.S. and Mode
Page 149 and 150: AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152: AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154: Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156: Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?