GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

Calibration Audit TrailAny changes to the existing calibration will increment the Calibration (CAL) audit trailat P60203.Setup Audit TrailChanges to any of the Setup Mode parameters will increment the setup audit trail atP60204.Viewing Audit Trail ParametersAudit trail parameters may be viewed at any time.To view audit trail parameters: (Model 350 I.S.)1. Press [ZERO] + [SELECT].2. Press [ZERO] [PRINT] [UNITS] [TARE].3. Enter [60203] with the [PRINT] and [UNITS] keys.4. Press [SELECT] to view the selected audit trail.5. Press [ZERO] to return to the Weigh Mode.To view audit trail parameters: (Model 355 I.S.)1. Press [1] [0] [0] [SELECT].2. Press [6] [0] [2] [0] [3] [ENTER].3. Press [SELECT] to view the selected audit trail.4. Press [SELECT] to return to the Weigh Mode.130Model 350 I.S. and Model 355 I.S. Service Manual
7 TroubleshootingThis chapter contains error messages and information parameters, as well asinformation on setup parameter selections and A/D Calibration.7.1 Error MessagesThe Model 350/355 I.S. utilizes the following types of error messages: OperationalErrors, Setup Mode Errors, Hardware Errors, Calibration Errors, CommunicationErrors, and Miscellaneous Errors.7.1.1 Operational ErrorsCodeCode02DescriptionUnder Load. Input signal is less than negative full scale. Check load cell wiring. Verify correct capacityselection at P110.Code03Over Load. Input signal is greater than positive full scale. Use same checks as "under load" above.Funct ~ Disbl Attempted to perform a function disabled in the Setup Mode.Code 04The digits on the display have exceeded the six digit display capacity.Code 05 Zero attempted beyond that allowed by P118.Code 08Input signal greatly exceeds the valid range. Check the load cell connection.Tare ~ Error Negative tare attempted when disabled (P440 enabled).Tare ~ GT FS Tare value greater than full scale capacity.DelayIndicates that a motion delay is in effect (zero, tare, etc.).Delay ~ Abort Acknowledges that a motion delayed function was aborted.Print ~ Abort Acknowledges that a motion delayed print request was aborted.Add ~ Load! If displayed after performing a count sample, this message indicates that a larger sample size is required.Out of ~ Range Attempted to enter a value beyond the allowable range.SPt 4~Error P5104 is based on quantity and the count parameter (P179) is disabled.Need APSA setpoint start is initiated and the setpoint is based on quantity and no piece weight has been established(start will not occur).Edit DisblUnable to edit the time and date because P502 is disabled.Model 350 I.S. and Model 355 I.S. Service Manual 131
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20:
TerminalEntity / Nonincendive Field
Page 21 and 22:
GasApprovalTemperatureRangeT class
Page 23 and 24:
2.5 Standard FunctionsThe Model 350
Page 25 and 26:
Safe Area OptionsBattery ChargerFib
Page 27 and 28:
2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30:
Key Press Weigh Mode Count Mode Set
Page 31 and 32:
2.11 Weigh Mode FunctionsThe Model
Page 33 and 34:
3 InstallationThe Model 350/355 I.S
Page 35 and 36:
3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38:
3.5 Remote Key ConnectionsThe Model
Page 39 and 40:
Battery ChargingTHE BATTERY MUST BE
Page 41 and 42:
3. Snap the (4) ½ plastic standoff
Page 43 and 44:
Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46:
Install the setpoint or Analog opti
Page 47 and 48:
3.8.5 Safe Area Analog Option Insta
Page 49 and 50:
4 ConfigurationThis section covers
Page 51 and 52:
To access the previous parameter1.
Page 53 and 54:
To setup a full scale value (exampl
Page 55 and 56:
4.5.2 Return to factory default (35
Page 57 and 58:
ParameterNumberDisplayNameP296.00 E
Page 59 and 60:
P115 Stability Delay (Selection)Sel
Page 61 and 62:
P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64:
P292 End Character (Key-in)Set the
Page 65 and 66:
P802 Tare and Zero Execution (Selec
Page 67 and 68:
is an 'O' (overload/underload), 'M'
Page 69 and 70:
4.9 ID Number Entry and PrintingIt
Page 71 and 72:
4.10.4 Entering ASCII Control Codes
Page 73 and 74:
The default format code for all par
Page 75 and 76:
4.12.2 Model 355 I.S.To sample usin
Page 77 and 78:
4.14 Remote Key ConfigurationThe Mo
Page 79 and 80:
4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113 and 114: ParameterSettingDisplayedNameDescri
Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122: First Zero Calibration Method (355
Page 123 and 124: 9. Pause for motion delay.10. Press
Page 125 and 126: 13. Pause for motion delay.14. Pres
Page 127 and 128: If the calibration weight value was
Page 129 and 130: 6 Legal for TradeThe Model 350/355
Page 131: 6.4.1 Physical SealThe most common
Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138: Table 7.1 Information Parameters.Pa
Page 139 and 140: 8 MaintenanceThe mainboard, keypad
Page 141 and 142: 5. Connect the keypad cable to the
Page 143 and 144: 9 Label DrawingsReference for Model
Page 145 and 146: 9.5 355 I.S. Generic Rear Label (5
Page 147 and 148: Appendix A: Model 350 I.S. and Mode
Page 149 and 150: AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152: AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154: Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156: Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?