GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

First Zero?1. Remove all weight and press [TARE] or [ENTER].2. From the Enter Load prompt key in the first calibration point and press [TARE]or [ENTER].3. From the Add Load prompt add the weight of the first calibration point andpress [TARE] or [ENTER].4. For calibration points 2 -5; Simply add the weight which you want to use for thenext calibration point, then key in the value of the applied weight and press[TARE] or [ENTER]. You may wish to add weight until the displayed weightdiffers from the actual applied weight and then perform the next calibration atthat point.Reset Cal1. Press [TARE] or [ENTER].2. From the First Zero?prompt remove all weight and press [TARE] or [ENTER].3. From the Enter Load prompt key in the first calibration point and press [TARE]or [ENTER].4. From the Add Load prompt add the weight of the first calibration point andpress [TARE] or [ENTER].5. For calibration points 2 -5; Simply add the weight which you want to use for thenext calibration point, then key in the total applied weight and press [TARE] or[ENTER]. You may wish to add weight until the displayed weight differs fromthe actual applied weight and then perform the next calibration at that point.Up to five calibration points may be established using this procedure. However if fewercalibration points are required, simply press [TARE] or [ENTER] without entering avalue at the PntX prompt.After the last point is established, the indicator will prompt with Cal ~ Good? Press the[TARE] or [ENTER]. key to accept the calibration or press [ZERO] or [CLR] to backupand redo the last point as described below.If you make a mistake at any point in the linearization process, simply press the [ZERO]or [CLR] key. The indicator w backup one step in the procedure to the previouslinearization point.After the linearization has been completed, the changes must be saved by pressing[TARE] or [ENTER] at the Enter = Save prompt. Otherwise the previous calibration datawill remain in effect.Examining Calibration ResultsIf Multi-Point Linearization is enabled (P119), the ten Parameters P61130 thru P61139show the calibration weights used and the resulting calculated factors. Otherwise themessage Not Used is displayed.Establishing a SpanOnce a zero reference has been established, the Model 350/355 I.S. displays Enter ~Load and awaits the entry of a span (test load) value. This value may be entered beforeor after the test load has been applied.124Model 350 I.S. and Model 355 I.S. Service Manual
If the calibration weight value was entered before applying the test weight, Add ~ Loadis displayed indicating that the test weight should now be applied. Apply the test weight,press [TARE] or [ENTER] and proceed to Exiting Calibration on page 125.If it is necessary to repeat the calibration process, press [ZERO] at the Cal ~ Good?prompt and repeat the calibration process.Establishing span with a 100lb test weight:1. Place a 100lb test weight on scale.2. Enter [1] [0] [0].3. Press [ZERO] or [ENTER] to establish span.4. Pause for motion delay.When making a significant change to the previous calibration, or when the calibrationweight is less than 5% of full scale capacity, ReCal ~ ??? will be displayed instead ofCal ~ Good? In this event it is recommended that the calibration be performed a secondtime. Press [TARE] or [ENTER] to recalibrate, or press [ZERO] to skip recalibration.5.2.8 Exiting CalibrationOnce zero and span have been established, the newly acquired calibration informationmust be saved to non-volatile memory before it will be realized in the Weigh Mode.When saving calibration, parameters changed in the setup mode are also saved withtheir new selections.To exit and save calibration information:1. Press [TARE] or [ENTER] to accept calibration.2. Press [TARE] or [ENTER] to save calibration.3. Press [TARE] or [ENTER] to exit calibration.To exit without saving calibration information:1. Press [TARE] or [ENTER] to accept calibration.2. Press [ZERO].3. Press [TARE] or [ENTER].4. Press [TARE] or [ENTER] to exit calibration.Model 350 I.S. and Model 355 I.S. Service Manual 125
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20:
TerminalEntity / Nonincendive Field
Page 21 and 22:
GasApprovalTemperatureRangeT class
Page 23 and 24:
2.5 Standard FunctionsThe Model 350
Page 25 and 26:
Safe Area OptionsBattery ChargerFib
Page 27 and 28:
2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30:
Key Press Weigh Mode Count Mode Set
Page 31 and 32:
2.11 Weigh Mode FunctionsThe Model
Page 33 and 34:
3 InstallationThe Model 350/355 I.S
Page 35 and 36:
3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38:
3.5 Remote Key ConnectionsThe Model
Page 39 and 40:
Battery ChargingTHE BATTERY MUST BE
Page 41 and 42:
3. Snap the (4) ½ plastic standoff
Page 43 and 44:
Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46:
Install the setpoint or Analog opti
Page 47 and 48:
3.8.5 Safe Area Analog Option Insta
Page 49 and 50:
4 ConfigurationThis section covers
Page 51 and 52:
To access the previous parameter1.
Page 53 and 54:
To setup a full scale value (exampl
Page 55 and 56:
4.5.2 Return to factory default (35
Page 57 and 58:
ParameterNumberDisplayNameP296.00 E
Page 59 and 60:
P115 Stability Delay (Selection)Sel
Page 61 and 62:
P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64:
P292 End Character (Key-in)Set the
Page 65 and 66:
P802 Tare and Zero Execution (Selec
Page 67 and 68:
is an 'O' (overload/underload), 'M'
Page 69 and 70:
4.9 ID Number Entry and PrintingIt
Page 71 and 72:
4.10.4 Entering ASCII Control Codes
Page 73 and 74:
The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113 and 114: ParameterSettingDisplayedNameDescri
Page 115 and 116: Custom Transmit :1. [.002] [ENTER]
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122: First Zero Calibration Method (355
Page 123 and 124: 9. Pause for motion delay.10. Press
Page 125: 13. Pause for motion delay.14. Pres
Page 129 and 130: 6 Legal for TradeThe Model 350/355
Page 131 and 132: 6.4.1 Physical SealThe most common
Page 133 and 134: 7 TroubleshootingThis chapter conta
Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138: Table 7.1 Information Parameters.Pa
Page 139 and 140: 8 MaintenanceThe mainboard, keypad
Page 141 and 142: 5. Connect the keypad cable to the
Page 143 and 144: 9 Label DrawingsReference for Model
Page 145 and 146: 9.5 355 I.S. Generic Rear Label (5
Page 147 and 148: Appendix A: Model 350 I.S. and Mode
Page 149 and 150: AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152: AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154: Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156: Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?