GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

More documents

Recommendations

Info

Display (P271)When set for Display, information will be displayed on the remote indicator exactly asit appears on the master indicator.Set P271 for Display and configure all other remote display parameters. Configure theparameters in the master indicator (refer to Setup Master Indicator on page 109). Makesure that the wiring connections between the master and remote indicators are correct(refer to Remote Display Connections on page 35).Custom (P271)When set for Custom, the master indicator will send customized information to bedisplayed on the remote indicator. A parameter or text data may be transmitted to theremote indicator on a continual or "on demand" basis.Set P271 for Custom and set all other remote display parameters (refer to Table 4.4).Configure the parameters in the master indicator (refer to Setup Master Indicator onpage 109). Make sure that the wiring connections between the master and remoteindicators are correct (refer to Remote Display Connections on page 35. Follow theinstructions below for configuring the master indicator.1. Turn echo off at P290.2. Set the transmit to be continuous at P210 (port 1) or P230 (port 2). This is theport going to the remote indicator.3. Program custom transmit in the master indicator at P1000 (port 1) or P2000(port 2). See the example below for instructions on programming a customtransmit.If time out is enabled (P270), then the transmit should be set for continuous at P210 orP230 and have stability disabled at P212 or P232Example:The master indicator will be active and the Net weight will be displayed on the remoteindicator. The net and lb annunciators will illuminate. The codes for the annunciatorswill be entered as they are control codes (see Entering ASCII Control Codes on page69. The address of the remote indicator at P272 is 4. If P272 is set to None!, do notenter anything for the address field.Access custom transmit 1 (P1000) or custom transmit 2 (P2000).Format String:If P274 and P275 = 1 - 255, , , , , orIf P274 or P275 = 0, , , , 112Model 350 I.S. and Model 355 I.S. Service Manual
Custom Transmit :1. [.002] [ENTER] or [TARE] - 2. [.004] [ENTER] or [TARE] - 3. [.016] [ENTER] or [TARE] - 4. [.064] [ENTER] or [TARE] - 5. [ENTER] or [TARE], [1], [ENTER] or [TARE], [160], [ENTER] or [TARE] - 6. [.003] [ENTER] or [TARE] - 7. Save changes and exit the setup mode.ASCII Code 128 64 32 16 8 4 2 0Annunciator 1 Good2 Gross Net Qty Other kgAnnunciator 2 lb Spt 1 Spt 2 Spt 3 >0< MotionThe start character and end character can be any ASCII character 1 - 255. Refer toTable 4.5 for the annunciator codes to be entered in the custom transmit. Always use160 for the format code when entering a parameter.4.28.4 Hazardous Area to Safe Area ConfigurationIn order to use setpoints or analog output modules they must be located in the safearea. These modules will be installed in the safe area hub. Refer to Safe Area SetpointOption Installation or Safe Area Analog Option Installation on page 44 for optioninstallation instructions. The control indicator will be in the hazardous area and wherethe load cell(s) will be connected. The control and hub indicators will communicate viafiber optic cable. Refer to Fiber Optic Interface on page 38 for installation instructions.Use the following instructions to setup the control and hub indicators. Once a controlor hub indicator is chosen at P260, the protocol and interactive parameters areautomatically set up. See Table 4.5 for the default parameters of the control and hub.The setpoint and analog output parameters are only set in the control indicator (referto Setpoint Setup on page 77 or Analog Output Setup on page 101). The hub indicatorwill echo the control indicator.Make sure the controller and hub are connected with the fiber-optic kit and fiber-opticcable. Setup the hub indicator first and either cycle power or enter then exit the setupmode. This will synchronize P176, P177, P61200 - P61205.Simple Setup (Hub Indicator):1. Set P260 for Hub.2. Exit the setup mode.Simple Setup (Control Indicator):1. Set P260 for Cntrl.2. Exit the setup mode.Model 350 I.S. and Model 355 I.S. Service Manual 113
Page 1 and 2:
Model 350I.S. and Model 355I.S.Inst
Page 3 and 4:
Table of ContentsChapter 1 General
Page 5 and 6:
Start Fill ........................
Page 7 and 8:
1 General Information and Warnings1
Page 9 and 10:
1.3.3 Safe Handling of Equipment wi
Page 11 and 12:
1.8 FCC and EMC Declarations of Com
Page 13 and 14:
2 IntroductionThis section explains
Page 15 and 16:
Note: Electrical apparatus Approved
Page 17 and 18:
Ca or Co - the maximum capacitance
Page 19 and 20:
TerminalEntity / Nonincendive Field
Page 21 and 22:
GasApprovalTemperatureRangeT class
Page 23 and 24:
2.5 Standard FunctionsThe Model 350
Page 25 and 26:
Safe Area OptionsBattery ChargerFib
Page 27 and 28:
2.9 350 I.S. KeypadThe Model 350 I.
Page 29 and 30:
Key Press Weigh Mode Count Mode Set
Page 31 and 32:
2.11 Weigh Mode FunctionsThe Model
Page 33 and 34:
3 InstallationThe Model 350/355 I.S
Page 35 and 36:
3.2.2 Model 355 I.S.Figure 3.3 Mode
Page 37 and 38:
3.5 Remote Key ConnectionsThe Model
Page 39 and 40:
Battery ChargingTHE BATTERY MUST BE
Page 41 and 42:
3. Snap the (4) ½ plastic standoff
Page 43 and 44:
Figure 3.12 Fiber-optic Cable Insta
Page 45 and 46:
Install the setpoint or Analog opti
Page 47 and 48:
3.8.5 Safe Area Analog Option Insta
Page 49 and 50:
4 ConfigurationThis section covers
Page 51 and 52:
To access the previous parameter1.
Page 53 and 54:
To setup a full scale value (exampl
Page 55 and 56:
4.5.2 Return to factory default (35
Page 57 and 58:
ParameterNumberDisplayNameP296.00 E
Page 59 and 60:
P115 Stability Delay (Selection)Sel
Page 61 and 62:
P204 Comm Handshake (Comm 1) (Selec
Page 63 and 64: P292 End Character (Key-in)Set the
Page 65 and 66: P802 Tare and Zero Execution (Selec
Page 67 and 68: is an 'O' (overload/underload), 'M'
Page 69 and 70: 4.9 ID Number Entry and PrintingIt
Page 71 and 72: 4.10.4 Entering ASCII Control Codes
Page 73 and 74: The default format code for all par
Page 75 and 76: 4.12.2 Model 355 I.S.To sample usin
Page 77 and 78: 4.14 Remote Key ConfigurationThe Mo
Page 79 and 80: 4.16 Setpoint SetupThe Model 350/35
Page 81 and 82: Pre-act values are entered in terms
Page 83 and 84: 4. Next the PctHi value will be dis
Page 85 and 86: 3. Press [TARE]. Once the tare key
Page 87 and 88: 4.19.1 Enter a TargetPressing [TARE
Page 89 and 90: ParameterSettingPre-Act 2 = 236 15,
Page 91 and 92: 4.20.3 Start DischargeActivation Me
Page 93 and 94: 3a. If a value is desired, enter it
Page 95 and 96: 4.22 Absolute CheckweighThis progra
Page 97 and 98: 4.23 Target Deviation CheckweighThe
Page 99 and 100: 4.24 Batch 2The batch 2 program is
Page 101 and 102: 4.25 Independent Setpoint Operation
Page 103 and 104: 4.25.3 ExampleSetup a continuous-cy
Page 105 and 106: Bars ON Weight Range (Lower Toleran
Page 107 and 108: ParameterSettingDisplayedNameDescri
Page 109 and 110: 4.27.2 Analog Output ExampleAnalogP
Page 111 and 112: 4.28.2 Setup Master IndicatorSet th
Page 113: ParameterSettingDisplayedNameDescri
Page 117 and 118: 4.28.5 300 Series Command CodesHex
Page 119 and 120: 5 CalibrationThis chapter covers al
Page 121 and 122: First Zero Calibration Method (355
Page 123 and 124: 9. Pause for motion delay.10. Press
Page 125 and 126: 13. Pause for motion delay.14. Pres
Page 127 and 128: If the calibration weight value was
Page 129 and 130: 6 Legal for TradeThe Model 350/355
Page 131 and 132: 6.4.1 Physical SealThe most common
Page 133 and 134: 7 TroubleshootingThis chapter conta
Page 135 and 136: 7.1.4 Calibration ErrorsCodeF.S. ~T
Page 137 and 138: Table 7.1 Information Parameters.Pa
Page 139 and 140: 8 MaintenanceThe mainboard, keypad
Page 141 and 142: 5. Connect the keypad cable to the
Page 143 and 144: 9 Label DrawingsReference for Model
Page 145 and 146: 9.5 355 I.S. Generic Rear Label (5
Page 147 and 148: Appendix A: Model 350 I.S. and Mode
Page 149 and 150: AWT35-500389ABModel 350 I.S. and Mo
Page 151 and 152: AWT35-500389ABModel 350 I.S. and Mo
Page 153 and 154: Uo or Voc or Vt ≤ Vmax, Io or Isc
Page 156: Avery Weigh-Tronix USA1000 Armstron
show all

GSE 350IS / GSE 355IS Service Manual - Advanced Weigh ...

Create successful ePaper yourself

Delete template?

Save as template?