Emotron MSF 2.0 Softstarter

More documents

Recommendations

Info

Analogue/digital input valueValue on the analogue/digital input as a percentage of theinput range. This read-out depends on the configuration ofthe analogue/digital input in menu [500], e.g. if the analogue/digitalinput is configured for analogue start/stop0-10 V/0-20 mA (alternative 6), an input signal of 4 V or8 mA will be shown as 40%. However, if the analogue/digitalinput is configured for analogue start/stop 2.10 V/4-20mA (alternative 7), an input signal of 4 V or 8 mA will beshown as 25%.7 2 3Range: 0-100%Analogue/digital input valueRelay statusStatus of the relays K1 to K3 from the left to the right. L orH are displayed for relay status low (opened) or high(closed). The status described for relay K3 corresponds tothe status of terminals 31 and 32.7 2 4Range:0LLL-HHHRelay statusRead-outAnalogue Output valueValue on the analogue output as a percentage of the outputrange. This read-out depends on the configuration of theanalogue output in menu [520], e.g. if the analogue/digitalinput is configured for 0-10 V/0-20 mA (alternative 1) orfor 10-0 V/20-0 mA (alternative 3), an output signal of 4 Vor 8 mA will be shown as 40%. However, if the analogueoutput is configured for 2-10 V/4-20 mA (alternative 2) or10-2 V/20-4 mA (alternative 4), an output signal of 4 V or8 mA will be shown as 25%.7 2 5LLLRead-outRead-out8.10.3 Stored valuesOperation time. The operation time is the time duringwhich the motor connected to the softstarter is running, notthe time during which the supply power is on.If the actual value for the operation time exceeds 9999 hoursthe display will alternate between the four lower digits andthe higher digits.ExampleIf the actual operation time is 12467, 1 will be shown for1 s, then 2467 will be shown for 5 s and so on.7 30Range:0-9 999 999 hEnergy consumption7 3 1Range:Operation time0.000-2000 MWhEnergy consumptionReset energy consumptionIn this menu the stored power consumption (menu [713])can be reset to 0.Default:Range:noYES00. 0 0 07 32n oReset energy consumptionnono, YESNo actionReset power consumptionRead-outRead-outMulti Setting0Analogue Output valueRange: 0-100%Emotron AB 01-4135-01r2 Functional description 95
8.11 Alarm listThe alarm list is generated automatically. It shows the latest15 alarms (F1-F17). The alarm list can be useful for trackingfailures in the softstarter or its control circuit. In the alarmlist both the alarm message and the operation time is savedfor each alarms that occurs. In menu [800] the latest alarmmessage and the corresponding operation time are shownalternately, in the same way, older alarms are shown inmenus [801] to [814].Example• If the latest alarm was a phase input failure (F1), whichoccurred at operation time 524. F1 is shown for 4 s then524 is shown for 2 s and so on.• If the latest alarm was a thermal motor protection alarm(F2), which occurred at operation time 17852. F2 isshown for 3 s, after that 1 is shown for 1 s, then 7852 isshown for 2 s and so on.Alarm list, latest error8 00Range:F1-F17Alarm list, error8 01F 1F 1Alarm list, latest errorAlarm list, error 14Read-outRead-out8.12 Softstarter dataIn menus [900] to [902] the softstarter type is shown andthe softstarter’s software version is specified.Softstarter type9 00Range:Software variant9 01VRange:17-1400 ASame as labelSoftware versionRange:29 02R1 72 01 5Same as labelSoftstarter typeSoftware variant textSoftware version textRead-outRead-outRead-outRange:F1-F17Menu Function802 Alarm list, error 13803 Alarm list, error 12804 Alarm list, error 11805 Alarm list, error 10806 Alarm list, error 9807 Alarm list, error 8808 Alarm list, error 7809 Alarm list, error 6810 Alarm list, error 5811 Alarm list, error 4812 Alarm list, error 3813 Alarm list, error 2814 Alarm list, error 196 Functional description Emotron AB 01-4135-01r2
Page 1 and 2:
Emotron MSF 2.0SoftstarterInstructi
Page 4 and 5:
Safety instructionsSafetyThe softst
Page 6 and 7:
ContentsSafety instructions .......
Page 8 and 9:
1. General informationThis manual d
Page 10 and 11:
1.8 Glossary1.8.1 AbbreviationsIn t
Page 12 and 13:
2. DescriptionT/T nn/n sIn this cha
Page 14 and 15:
The disadvantage of the star-delta
Page 16 and 17:
T/T n2,521,510,5Torquef 3
Page 18 and 19:
3. MountingThis chapter describes h
Page 20 and 21:
Mounting schemesMSF-017 to MSF-250T
Page 22 and 23:
4. ConnectionsThe description of in
Page 24 and 25:
Fig. 20 Connection of MSF-110 to MS
Page 26 and 27:
Fig. 22 Connection of MSF-310 to MS
Page 28 and 29:
4.3 Minimum wiringThe figure below
Page 30 and 31:
5. How to get startedThis chapter b
Page 32 and 33:
5.5 Setting the start commandAs def
Page 34 and 35:
6. Applications and functions selec
Page 37 and 38:
Table 10Applications Rating ListApp
Page 39 and 40:
Table 11Application Functions ListA
Page 41 and 42:
38 Applications and functions selec
Page 43 and 44:
The control panel is used for selec
Page 45 and 46:
7.7 Overview of softstarteroperatio
Page 47 and 48: 8.1 General settingsGeneral setting
Page 49 and 50: Nominal motor speed.2 1 314Nominal
Page 51 and 52: Overload time (s)Normal loadInterna
Page 53 and 54: NOTE: Check that the motor current
Page 55 and 56: 8.4.3 Reset to factory setting [243
Page 57 and 58: External alarm auto reset [257]This
Page 59 and 60: With voltage control the output vol
Page 61 and 62: To optimize the start, use the sett
Page 63 and 64: Torque boost current limit [316]In
Page 65: NOTE: For several start/stops it is
Page 68 and 69: Slow speed controlled by an externa
Page 70 and 71: JOG commands can be given via analo
Page 72 and 73: Power Factor Control PFC [341]Durin
Page 74 and 75: Max power alarm [400]In this menu m
Page 76: Min power alarm response delay [410
Page 79 and 80: Undervoltage level [437]This menu i
Page 81 and 82: Relay outputsPTC inputPTCCurrent tr
Page 83 and 84: Analogue start/stop off-value [503]
Page 85 and 86: Digital input 3 function [512]In th
Page 87 and 88: Scaling analogue output, max [523]T
Page 89 and 90: K1 contact function [533]In this me
Page 91 and 92: !CAUTION: Very high currents can ar
Page 93 and 94: For applications which use the reve
Page 95 and 96: It is possible to use just one digi
Page 97: Line main voltage L1-L38.10.2 Statu
Page 101 and 102: whether they need a Reset signal (m
Page 103 and 104: 100 Protection and alarm Emotron AB
Page 105 and 106: Observation Fault indication Cause
Page 107 and 108: Observation Fault indication Cause
Page 109 and 110: 106 Maintenance Emotron AB 014135-0
Page 111 and 112: 12.3.1 Cable kit for external curre
Page 113 and 114: 110 Options Emotron AB 01-4135-01r2
Page 115 and 116: Table 19Typical motor power at main
Page 117 and 118: Table 21Typical motor power at main
Page 119 and 120: 13.2 General electrical specificati
Page 121 and 122: Table 25Power lossesModelPower loss
Page 123 and 124: 13.5 Derating at highertemperatureB
Page 125 and 126: 13.9 Semi-conductor fusesAlways use
Page 127 and 128: Table 27Parameter listMenuno.Functi
Page 135: Operation R .......................
Page 138: Emotron AB, Mörsaregatan 12, SE-25
show all

Emotron MSF 2.0 Softstarter

Create successful ePaper yourself

Delete template?

Save as template?