Emotron MSF 2.0 Softstarter
Emotron MSF 2.0 Softstarter Emotron MSF 2.0 Softstarter
1. General informationThis manual describes the Emotron Softstarter MSF 2.0.1.1 How to use the InstructionManualThis instruction manual tells you how to install and operatethe softstarter MSF 2.0. Read the whole Instruction Manualbefore installing and putting the unit into operation.Once you are familiar with the softstarter, you can operate itfrom the control panel by referring to chapter 5. page 27.This chapter describes all the functions and possible settings.1.2 Integrated safety systemsThe device is equipped with a protection system whichreacts to:• Over temperature• Voltage unbalance• Over- and under voltage• Phase reversal• Phase loss• Motor overload protection thermal and PTC.• Motor shaft power monitor, protecting machine or processmaximum or minimum alarm.• Starts per hour limitationThe softstarter is equipped with a connection for protectiveearth (PE).All MSF 2.0 softstarters are IP 20 enclosed types, exceptMSF-1000 and MSF-1400 which are delivered as openchassis IP00.1.3 Safety measuresThese instructions are a constituent part of the device andmust be:• Available to competent personnel at all times.• Read prior to installation of the device.• Observed with regard to safety, warnings and informationgiven.The tasks in these instructions are described so that they canbe understood by people trained in electrical engineering.Such personnel must have appropriate tools and testinginstruments available. Such personnel must have beentrained in safe working methods.The safety measures laid down in DIN standard VDE 0100must be guaranteed.The user must obtain any general and local operating permitsand meet any requirements regarding:• Personnel safety• Product disposal• Environmental protectionNOTE! The safety measures must remain in force at alltimes. Should questions or uncertainties arise, pleasecontact your local sales outlet.1.4 Notes to the InstructionManualNOTE: Additional information as an aid to avoidingproblems.ImportantFor all enquiries and spare parts orders, please quote the correctname of the device and serial number to ensure thatyour inquiry or order is dealt with correctly and swiftly.1.5 Type numberFig. 1, page 5 gives an example of the type code numberused for an Emotron MSF Softstarter. With this codenumber the exact type of the softstarter can be determined.This identification will be required for type specific informationwhen mounting and installing. The code number islocated on the product label, on the front of the unit.Fig. 1!CAUTION: Failure to follow these instructionscan result in malfunction or damage to thesoftstarter.WARNING: Failure to follow these instructionscan result in serious injury to the user in additionto serious damage to the softstarter.MSF -017 525 2 C V N I1 2 3 4 5 6 7 8Type number.Emotron AB 01-4135-01r2 General information 5
Table 1PositionConfigurationparameterDescription1 Softstarter type MSF 2.0 type, Fixed2 Motor current 017-1400 A34567Mains supplyvoltageControl supplyvoltageControl paneloptionCoated boardsoptionCommunicationoption8 IT-net option525=200-525 V690=200-690 V2=100-240 V5=380-500 VC=Standard, no externalcontrol panelH=External control panel-=No coated boardsV=Coated boardsN=No COM includedS=RS232/485 includedD=DeviceNet includedP=Profibus included-=StandardI=Special connection forIT earthing systemNOTE: With the IT-net option outer measures have to betaken to fulfil EMC regulations according to section13.7, page 120.1.7 Unpacking MSF-310 andlarger typesThe MSF 2.0 softstarter is attached to the plywood box/loading stool by screws, and the softstarter must beunpacked as follows:1. Open only the securing plates at the bottom of the box(bend downwards). Then lift up the box from the loadingstool, both top and sides in one piece.2. Loosen the three (3) screws on the front cover of thesoftstarter unit, down by the lower logo.3. Push up the front cover about 20 mm so that the frontcover can be removed.4. Remove the two (2) mounting screws at the bottom ofthe softstarter.5. Lift up the softstarter unit at the bottom about 10 mmand then push backwards about 20 mm so that the softstartercan be removed from the mounting hooks* at thetop. The hooks are placed under the bottom plate andcannot be removed until the softstarter is pulled out.6. Loosen the two screws (2) for the mounting hooks andremove the hooks.7. The hooks are used as an upper support for mountingthe softstarter.1.6 Transport and packingThe device is packed in a carton or plywood box for delivery.The outer packaging can be recycled. The devices are carefullychecked and packed before dispatch, but transportdamage cannot be ruled out.Check on receiptCheck that the goods are complete as listed on the deliverynote, see type no. etc. on the rating plate.Is the packaging damaged?Check the goods for damage (visual check).If you have cause for complaintIf the goods have been damaged during transport:• Contact the transport company or the supplier immediately.• Keep the packaging (for inspection by the transportcompany or for returning the device).Packaging for returning the devicePack the device so that it will resist shock and impact.Intermediate storageAfter delivery or after it has been dismounted, the device canbe stored before further use in a dry room.Fig. 2Unpacking MSF-310 and larger models.6 General information Emotron AB 01-4135-01r2
- Page 1 and 2: Emotron MSF 2.0SoftstarterInstructi
- Page 4 and 5: Safety instructionsSafetyThe softst
- Page 6 and 7: ContentsSafety instructions .......
- Page 10 and 11: 1.8 Glossary1.8.1 AbbreviationsIn t
- Page 12 and 13: 2. DescriptionT/T nn/n sIn this cha
- Page 14 and 15: The disadvantage of the star-delta
- Page 16 and 17: T/T n2,521,510,5Torquef 3
- Page 18 and 19: 3. MountingThis chapter describes h
- Page 20 and 21: Mounting schemesMSF-017 to MSF-250T
- Page 22 and 23: 4. ConnectionsThe description of in
- Page 24 and 25: Fig. 20 Connection of MSF-110 to MS
- Page 26 and 27: Fig. 22 Connection of MSF-310 to MS
- Page 28 and 29: 4.3 Minimum wiringThe figure below
- Page 30 and 31: 5. How to get startedThis chapter b
- Page 32 and 33: 5.5 Setting the start commandAs def
- Page 34 and 35: 6. Applications and functions selec
- Page 37 and 38: Table 10Applications Rating ListApp
- Page 39 and 40: Table 11Application Functions ListA
- Page 41 and 42: 38 Applications and functions selec
- Page 43 and 44: The control panel is used for selec
- Page 45 and 46: 7.7 Overview of softstarteroperatio
- Page 47 and 48: 8.1 General settingsGeneral setting
- Page 49 and 50: Nominal motor speed.2 1 314Nominal
- Page 51 and 52: Overload time (s)Normal loadInterna
- Page 53 and 54: NOTE: Check that the motor current
- Page 55 and 56: 8.4.3 Reset to factory setting [243
- Page 57 and 58: External alarm auto reset [257]This
Table 1PositionConfigurationparameterDescription1 <strong>Softstarter</strong> type <strong>MSF</strong> <strong>2.0</strong> type, Fixed2 Motor current 017-1400 A34567Mains supplyvoltageControl supplyvoltageControl paneloptionCoated boardsoptionCommunicationoption8 IT-net option525=200-525 V690=200-690 V2=100-240 V5=380-500 VC=Standard, no externalcontrol panelH=External control panel-=No coated boardsV=Coated boardsN=No COM includedS=RS232/485 includedD=DeviceNet includedP=Profibus included-=StandardI=Special connection forIT earthing systemNOTE: With the IT-net option outer measures have to betaken to fulfil EMC regulations according to section13.7, page 120.1.7 Unpacking <strong>MSF</strong>-310 andlarger typesThe <strong>MSF</strong> <strong>2.0</strong> softstarter is attached to the plywood box/loading stool by screws, and the softstarter must beunpacked as follows:1. Open only the securing plates at the bottom of the box(bend downwards). Then lift up the box from the loadingstool, both top and sides in one piece.2. Loosen the three (3) screws on the front cover of thesoftstarter unit, down by the lower logo.3. Push up the front cover about 20 mm so that the frontcover can be removed.4. Remove the two (2) mounting screws at the bottom ofthe softstarter.5. Lift up the softstarter unit at the bottom about 10 mmand then push backwards about 20 mm so that the softstartercan be removed from the mounting hooks* at thetop. The hooks are placed under the bottom plate andcannot be removed until the softstarter is pulled out.6. Loosen the two screws (2) for the mounting hooks andremove the hooks.7. The hooks are used as an upper support for mountingthe softstarter.1.6 Transport and packingThe device is packed in a carton or plywood box for delivery.The outer packaging can be recycled. The devices are carefullychecked and packed before dispatch, but transportdamage cannot be ruled out.Check on receiptCheck that the goods are complete as listed on the deliverynote, see type no. etc. on the rating plate.Is the packaging damaged?Check the goods for damage (visual check).If you have cause for complaintIf the goods have been damaged during transport:• Contact the transport company or the supplier immediately.• Keep the packaging (for inspection by the transportcompany or for returning the device).Packaging for returning the devicePack the device so that it will resist shock and impact.Intermediate storageAfter delivery or after it has been dismounted, the device canbe stored before further use in a dry room.Fig. 2Unpacking <strong>MSF</strong>-310 and larger models.6 General information <strong>Emotron</strong> AB 01-4135-01r2
Change language