Emotron MSF 2.0 Softstarter

More documents

Recommendations

Info

8. Functional descriptionThis functional description for Softstarter MSF 2.0describes the menus and parameters in the softstarter unit.You will find a short description of each function, their aimsand settings.The MSF 2.0 provides extensive setting possibilities viamenus on the control panel, remote control or serial communication.The menus are numbered according to themenu overview in Table 11.Table 15Menu overviewFunction Menu number Description See sectionGeneral settings100-101200-202General basic settings. 8.1Motor data 210-215 For insertion of technical data for the actual motor. 8.2Motor protection 220-231 Protection associated with the motor in the application. 8.3Parameter sethandling240-243 Selection and configuration of parameter sets. 8.4Auto reset 250-263 Automatic reset of active alarm and restart of MSF 2.0. 8.5Serialcommunication270-273 Serial communication settings for the data transfer. 8.6Operation settings 300-342Settings associated with the operation, for example the start- andstop procedures.8.7Process protection 400-440 Protection associated with the process. 8.8I/O settings 500-534 In- and output settings for control and monitoring. 8.9View operation 700-732 For read-out of measured values. 8.10Alarm list 800-814 Latest error. Available alarms. 8.11Softstarter data 900-902 Displays softstarter type, software variant and version. 8.12Emotron AB 01-4135-01r2 Functional description 43
8.1 General settingsGeneral settings for MSF 2.0 contains the following menus:[100] Current[101] Automatic return menu[200] Control source[201] Control panel locked for settings[202] Enable US units8.1.1 Current [100]This read-out menu shows the actual current to the motor.1 0 0Range:0. 00.0-9999ACurrentNOTE! This is the same read-out as menu [700].8.1.2 Automatic return menu [101]When the MSF 2.0 is powered up, menu [100] (Currentread-out) is shown as default. When another menu has beenselected by the user (moving through the menu list with the“NEXT” or “PREV” keys) this menu will remain active.Alternatively a specific menu can be chosen as automaticreturn menu. The chosen menu will be shown automaticallyafter 60 seconds without any control panel activity.1 0 1o F FAutomatic return menuDefault: oFFRange: oFF, 1-999oFFAutomatic return menu is disabled.1-999 Automatic return menu.Read-outSetting8.1.3 Control source [200]The softstarter can be controlled either via the control panel,remote control or the serial communication interface.Remote control via terminals 11,12 and 13 is the default setting.NOTE: Depending on the setting in this menu, thesoftstarter may be configured via control panel or viaserial communication. See Table 14, page 42 for moreinformation.NOTE: If control panel (1) or remote control (2) isconfigured, the setting can only be changed via controlpanel to serial communication control (3). However, ifserial communication control (3) is configured, thesetting can be changed either via serial communicationor via control panel.2 0 0Control sourceDefault: 2 (remote control)Range: 1, 2, 31 Control panel.2 Remote control.3 Serial communication control.8.1.4 Control panel lock [201]The MSF 2.0 Control panel can be locked to preventparameter being set by unauthorised personnel.• Lock control panel by simultaneously pressing both keys“NEXT ” and “ENTER ” for at least 2 seconds.The message “- Loc” will be displayed for 2 seconds.• To unlock control panel, simultaneously press the sametwo keys “NEXT ” and “ENTER ” for at least 2seconds. The message “unlo” will be displayed for 2 seconds.In locked mode, all parameters and read-out menus can bedisplayed, but it is forbidden to change any parameters viathe control panel.The message “-Loc” will be displayed if someone tries to seta parameter in locked mode.The key lock status can be read out in menu [201].NOTE: If parameter [200] is configured for serialcommunication control, the softstarter may still beconfigured via serial communication, regardless of thecontrol panel lock status.2 01oDefault:Range:noYES2F FControl panel locked forsettingsnooFF, onControl panel is not lockedControl panel is lockedSettingRead-out44 Functional description Emotron AB 01-4135-01r2
Page 1 and 2: Emotron MSF 2.0SoftstarterInstructi
Page 4 and 5: Safety instructionsSafetyThe softst
Page 6 and 7: ContentsSafety instructions .......
Page 8 and 9: 1. General informationThis manual d
Page 10 and 11: 1.8 Glossary1.8.1 AbbreviationsIn t
Page 12 and 13: 2. DescriptionT/T nn/n sIn this cha
Page 14 and 15: The disadvantage of the star-delta
Page 16 and 17: T/T n2,521,510,5Torquef 3
Page 18 and 19: 3. MountingThis chapter describes h
Page 20 and 21: Mounting schemesMSF-017 to MSF-250T
Page 22 and 23: 4. ConnectionsThe description of in
Page 24 and 25: Fig. 20 Connection of MSF-110 to MS
Page 26 and 27: Fig. 22 Connection of MSF-310 to MS
Page 28 and 29: 4.3 Minimum wiringThe figure below
Page 30 and 31: 5. How to get startedThis chapter b
Page 32 and 33: 5.5 Setting the start commandAs def
Page 34 and 35: 6. Applications and functions selec
Page 37 and 38: Table 10Applications Rating ListApp
Page 39 and 40: Table 11Application Functions ListA
Page 41 and 42: 38 Applications and functions selec
Page 43 and 44: The control panel is used for selec
Page 45: 7.7 Overview of softstarteroperatio
Page 49 and 50: Nominal motor speed.2 1 314Nominal
Page 51 and 52: Overload time (s)Normal loadInterna
Page 53 and 54: NOTE: Check that the motor current
Page 55 and 56: 8.4.3 Reset to factory setting [243
Page 57 and 58: External alarm auto reset [257]This
Page 59 and 60: With voltage control the output vol
Page 61 and 62: To optimize the start, use the sett
Page 63 and 64: Torque boost current limit [316]In
Page 65: NOTE: For several start/stops it is
Page 68 and 69: Slow speed controlled by an externa
Page 70 and 71: JOG commands can be given via analo
Page 72 and 73: Power Factor Control PFC [341]Durin
Page 74 and 75: Max power alarm [400]In this menu m
Page 76: Min power alarm response delay [410
Page 79 and 80: Undervoltage level [437]This menu i
Page 81 and 82: Relay outputsPTC inputPTCCurrent tr
Page 83 and 84: Analogue start/stop off-value [503]
Page 85 and 86: Digital input 3 function [512]In th
Page 87 and 88: Scaling analogue output, max [523]T
Page 89 and 90: K1 contact function [533]In this me
Page 91 and 92: !CAUTION: Very high currents can ar
Page 93 and 94: For applications which use the reve
Page 95 and 96: It is possible to use just one digi
Page 97 and 98:
Line main voltage L1-L38.10.2 Statu
Page 99 and 100:
8.11 Alarm listThe alarm list is ge
Page 101 and 102:
whether they need a Reset signal (m
Page 103 and 104:
100 Protection and alarm Emotron AB
Page 105 and 106:
Observation Fault indication Cause
Page 107 and 108:
Observation Fault indication Cause
Page 109 and 110:
106 Maintenance Emotron AB 014135-0
Page 111 and 112:
12.3.1 Cable kit for external curre
Page 113 and 114:
110 Options Emotron AB 01-4135-01r2
Page 115 and 116:
Table 19Typical motor power at main
Page 117 and 118:
Table 21Typical motor power at main
Page 119 and 120:
13.2 General electrical specificati
Page 121 and 122:
Table 25Power lossesModelPower loss
Page 123 and 124:
13.5 Derating at highertemperatureB
Page 125 and 126:
13.9 Semi-conductor fusesAlways use
Page 127 and 128:
Table 27Parameter listMenuno.Functi
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135:
Operation R .......................
Page 138:
Emotron AB, Mörsaregatan 12, SE-25
show all

Emotron MSF 2.0 Softstarter

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?