Emotron MSF 2.0 Softstarter

More documents

Recommendations

Info

Table 13The keysStart/stop motor operation.STARTSTOPDisplay previous menu.PREVDisplay next menu.NEXTDecrease value of setting.Increase value of setting.Confirm setting just made.Alarm reset.ENTERRESETJOG ReverseJOGJOG ForwardJOG7.6 Control panel lockThe control panel can be locked to prevent parameter beingset by unauthorised personnel.• Lock control panel by simultaneously pressing both“NEXT ” and “ENTER ” for at least 2 sec. Themessage ’- Loc’ will be displayed for 2 seconds whenlocked.• To unlock control panel, simultaneously press the same2 keys “NEXT ” and “ENTER ” for at least 2sec. The message ’unlo’ will be displayed for 2 secondswhen unlocked.In locked mode it is possible to operate the softstarter fromthe control panel and to view all parameters and read-outs,but it is not possible to change any parameters.<strong>Emotron</strong> AB 01-4135-01r2 Operation of the softstarter 41
7.7 Overview of softstarteroperation and parameterset-upTable showing how parameters can be set and operation carriedout.Table 14Control sourcesOperationControl sourceControl panel lockStart/StopAlarm resetSetting of parametersControl panelParameter [200]=1Unlockedcontrol panelLockedcontrol panelControl panel Control panel Control panelControl panel Control panel ------------------RemoteParameter [200]=2Unlockedcontrol panelLockedcontrol panelRemoteRemoteRemote andcontrol panelRemote andcontrol panelControl panel-------------------Serial comm.Parameter [200]=3Unlockedcontrol panelLockedcontrol panelSerial comm.Serial comm.Serial comm. andcontrol panelSerial comm. andcontrol panelSerial comm.Serial comm.NOTE: If external control of parameter set is chosen inmenu [240] no parameters except for parameter set[249] and control source [200] can be changed.42 Operation of the softstarter <strong>Emotron</strong> AB 01-4135-01r2
Page 1 and 2: Emotron MSF 2.0SoftstarterInstructi
Page 4 and 5: Safety instructionsSafetyThe softst
Page 6 and 7: ContentsSafety instructions .......
Page 8 and 9: 1. General informationThis manual d
Page 10 and 11: 1.8 Glossary1.8.1 AbbreviationsIn t
Page 12 and 13: 2. DescriptionT/T nn/n sIn this cha
Page 14 and 15: The disadvantage of the star-delta
Page 16 and 17: T/T n2,521,510,5Torquef 3
Page 18 and 19: 3. MountingThis chapter describes h
Page 20 and 21: Mounting schemesMSF-017 to MSF-250T
Page 22 and 23: 4. ConnectionsThe description of in
Page 24 and 25: Fig. 20 Connection of MSF-110 to MS
Page 26 and 27: Fig. 22 Connection of MSF-310 to MS
Page 28 and 29: 4.3 Minimum wiringThe figure below
Page 30 and 31: 5. How to get startedThis chapter b
Page 32 and 33: 5.5 Setting the start commandAs def
Page 34 and 35: 6. Applications and functions selec
Page 37 and 38: Table 10Applications Rating ListApp
Page 39 and 40: Table 11Application Functions ListA
Page 41 and 42: 38 Applications and functions selec
Page 43: The control panel is used for selec
Page 47 and 48: 8.1 General settingsGeneral setting
Page 49 and 50: Nominal motor speed.2 1 314Nominal
Page 51 and 52: Overload time (s)Normal loadInterna
Page 53 and 54: NOTE: Check that the motor current
Page 55 and 56: 8.4.3 Reset to factory setting [243
Page 57 and 58: External alarm auto reset [257]This
Page 59 and 60: With voltage control the output vol
Page 61 and 62: To optimize the start, use the sett
Page 63 and 64: Torque boost current limit [316]In
Page 65: NOTE: For several start/stops it is
Page 68 and 69: Slow speed controlled by an externa
Page 70 and 71: JOG commands can be given via analo
Page 72 and 73: Power Factor Control PFC [341]Durin
Page 74 and 75: Max power alarm [400]In this menu m
Page 76: Min power alarm response delay [410
Page 79 and 80: Undervoltage level [437]This menu i
Page 81 and 82: Relay outputsPTC inputPTCCurrent tr
Page 83 and 84: Analogue start/stop off-value [503]
Page 85 and 86: Digital input 3 function [512]In th
Page 87 and 88: Scaling analogue output, max [523]T
Page 89 and 90: K1 contact function [533]In this me
Page 91 and 92: !CAUTION: Very high currents can ar
Page 93 and 94: For applications which use the reve
Page 95 and 96:
It is possible to use just one digi
Page 97 and 98:
Line main voltage L1-L38.10.2 Statu
Page 99 and 100:
8.11 Alarm listThe alarm list is ge
Page 101 and 102:
whether they need a Reset signal (m
Page 103 and 104:
100 Protection and alarm Emotron AB
Page 105 and 106:
Observation Fault indication Cause
Page 107 and 108:
Observation Fault indication Cause
Page 109 and 110:
106 Maintenance Emotron AB 014135-0
Page 111 and 112:
12.3.1 Cable kit for external curre
Page 113 and 114:
110 Options Emotron AB 01-4135-01r2
Page 115 and 116:
Table 19Typical motor power at main
Page 117 and 118:
Table 21Typical motor power at main
Page 119 and 120:
13.2 General electrical specificati
Page 121 and 122:
Table 25Power lossesModelPower loss
Page 123 and 124:
13.5 Derating at highertemperatureB
Page 125 and 126:
13.9 Semi-conductor fusesAlways use
Page 127 and 128:
Table 27Parameter listMenuno.Functi
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135:
Operation R .......................
Page 138:
Emotron AB, Mörsaregatan 12, SE-25
show all

Emotron MSF 2.0 Softstarter

Create successful ePaper yourself

Delete template?

Save as template?