Emotron MSF 2.0 Softstarter
Emotron MSF 2.0 Softstarter Emotron MSF 2.0 Softstarter
Mounting schemesMSF-017 to MSF-250Table 8MSFModelHoledist.w1[mm]Holedist.H1[mm]Holedist. EHoledist. FDiam./screw-017, -030, -045 78.5 265 5.5/M5-060, -075, -085 78.5 265 5.5/M5-110, -145 128.5 345 5.5/M5-170, -210, -250 208.5 445 5.5/M5-310, -370, -450 460 450 44 39 8.5/M8-570, -710, -835 550 600 45.5 39 8.5/M8h1-1000, -1400 8.5/M8Observe that the two mounting hooks supplied (seesection 1.7, page 6 and Fig. 2 on page 6) must be used formounting the softstarter as upper support (only MSF-310 toMSF-835).208.5016.8046.0w103-F97_1Fig. 14 Hole pattern for MSF-017 to MSF-250 (backsideview).5474630.2003-F122_1Fig. 15 Hole pattern for screw attachment, MSF-310 toMSF-835. Hole distance (mm).Fig. 16 Hole pattern for MSF-170 to MSF-250 with uppermounting bracket instead of DIN rail.Emotron AB 01-4135-01r2 Mounting 17
Fig. 17 MSF-1000 to MSF-1400Fig. 18 Hole pattern busbar MSF-1000 to MSF-1400.18 Mounting Emotron AB 01-4135-01r2
- Page 1 and 2: Emotron MSF 2.0SoftstarterInstructi
- Page 4 and 5: Safety instructionsSafetyThe softst
- Page 6 and 7: ContentsSafety instructions .......
- Page 8 and 9: 1. General informationThis manual d
- Page 10 and 11: 1.8 Glossary1.8.1 AbbreviationsIn t
- Page 12 and 13: 2. DescriptionT/T nn/n sIn this cha
- Page 14 and 15: The disadvantage of the star-delta
- Page 16 and 17: T/T n2,521,510,5Torquef 3
- Page 18 and 19: 3. MountingThis chapter describes h
- Page 22 and 23: 4. ConnectionsThe description of in
- Page 24 and 25: Fig. 20 Connection of MSF-110 to MS
- Page 26 and 27: Fig. 22 Connection of MSF-310 to MS
- Page 28 and 29: 4.3 Minimum wiringThe figure below
- Page 30 and 31: 5. How to get startedThis chapter b
- Page 32 and 33: 5.5 Setting the start commandAs def
- Page 34 and 35: 6. Applications and functions selec
- Page 37 and 38: Table 10Applications Rating ListApp
- Page 39 and 40: Table 11Application Functions ListA
- Page 41 and 42: 38 Applications and functions selec
- Page 43 and 44: The control panel is used for selec
- Page 45 and 46: 7.7 Overview of softstarteroperatio
- Page 47 and 48: 8.1 General settingsGeneral setting
- Page 49 and 50: Nominal motor speed.2 1 314Nominal
- Page 51 and 52: Overload time (s)Normal loadInterna
- Page 53 and 54: NOTE: Check that the motor current
- Page 55 and 56: 8.4.3 Reset to factory setting [243
- Page 57 and 58: External alarm auto reset [257]This
- Page 59 and 60: With voltage control the output vol
- Page 61 and 62: To optimize the start, use the sett
- Page 63 and 64: Torque boost current limit [316]In
- Page 65: NOTE: For several start/stops it is
- Page 68 and 69: Slow speed controlled by an externa
Mounting schemes<strong>MSF</strong>-017 to <strong>MSF</strong>-250Table 8<strong>MSF</strong>ModelHoledist.w1[mm]Holedist.H1[mm]Holedist. EHoledist. FDiam./screw-017, -030, -045 78.5 265 5.5/M5-060, -075, -085 78.5 265 5.5/M5-110, -145 128.5 345 5.5/M5-170, -210, -250 208.5 445 5.5/M5-310, -370, -450 460 450 44 39 8.5/M8-570, -710, -835 550 600 45.5 39 8.5/M8h1-1000, -1400 8.5/M8Observe that the two mounting hooks supplied (seesection 1.7, page 6 and Fig. 2 on page 6) must be used formounting the softstarter as upper support (only <strong>MSF</strong>-310 to<strong>MSF</strong>-835).208.5016.8046.0w103-F97_1Fig. 14 Hole pattern for <strong>MSF</strong>-017 to <strong>MSF</strong>-250 (backsideview).5474630.2003-F122_1Fig. 15 Hole pattern for screw attachment, <strong>MSF</strong>-310 to<strong>MSF</strong>-835. Hole distance (mm).Fig. 16 Hole pattern for <strong>MSF</strong>-170 to <strong>MSF</strong>-250 with uppermounting bracket instead of DIN rail.<strong>Emotron</strong> AB 01-4135-01r2 Mounting 17
Change language