- Page 1 and 2:
Emotron MSF 2.0SoftstarterInstructi
- Page 4 and 5:
Safety instructionsSafetyThe softst
- Page 6 and 7:
ContentsSafety instructions .......
- Page 8 and 9:
1. General informationThis manual d
- Page 10 and 11:
1.8 Glossary1.8.1 AbbreviationsIn t
- Page 12 and 13:
2. DescriptionT/T nn/n sIn this cha
- Page 14 and 15:
The disadvantage of the star-delta
- Page 16 and 17:
T/T n2,521,510,5Torquef 3
- Page 18 and 19:
3. MountingThis chapter describes h
- Page 20 and 21:
Mounting schemesMSF-017 to MSF-250T
- Page 22 and 23:
4. ConnectionsThe description of in
- Page 24 and 25:
Fig. 20 Connection of MSF-110 to MS
- Page 26 and 27:
Fig. 22 Connection of MSF-310 to MS
- Page 28 and 29:
4.3 Minimum wiringThe figure below
- Page 30 and 31:
5. How to get startedThis chapter b
- Page 32 and 33:
5.5 Setting the start commandAs def
- Page 34 and 35:
6. Applications and functions selec
- Page 37 and 38:
Table 10Applications Rating ListApp
- Page 39 and 40:
Table 11Application Functions ListA
- Page 41 and 42:
38 Applications and functions selec
- Page 43 and 44:
The control panel is used for selec
- Page 45 and 46:
7.7 Overview of softstarteroperatio
- Page 47 and 48:
8.1 General settingsGeneral setting
- Page 49 and 50:
Nominal motor speed.2 1 314Nominal
- Page 51 and 52:
Overload time (s)Normal loadInterna
- Page 53 and 54:
NOTE: Check that the motor current
- Page 55 and 56:
8.4.3 Reset to factory setting [243
- Page 57 and 58:
External alarm auto reset [257]This
- Page 59 and 60:
With voltage control the output vol
- Page 61 and 62:
To optimize the start, use the sett
- Page 63 and 64:
Torque boost current limit [316]In
- Page 65: NOTE: For several start/stops it is
- Page 68 and 69: Slow speed controlled by an externa
- Page 70 and 71: JOG commands can be given via analo
- Page 72 and 73: Power Factor Control PFC [341]Durin
- Page 74 and 75: Max power alarm [400]In this menu m
- Page 76: Min power alarm response delay [410
- Page 79 and 80: Undervoltage level [437]This menu i
- Page 81 and 82: Relay outputsPTC inputPTCCurrent tr
- Page 83 and 84: Analogue start/stop off-value [503]
- Page 85 and 86: Digital input 3 function [512]In th
- Page 87 and 88: Scaling analogue output, max [523]T
- Page 89 and 90: K1 contact function [533]In this me
- Page 91 and 92: !CAUTION: Very high currents can ar
- Page 93 and 94: For applications which use the reve
- Page 95 and 96: It is possible to use just one digi
- Page 97 and 98: Line main voltage L1-L38.10.2 Statu
- Page 99 and 100: 8.11 Alarm listThe alarm list is ge
- Page 101 and 102: whether they need a Reset signal (m
- Page 103 and 104: 100 Protection and alarm Emotron AB
- Page 105 and 106: Observation Fault indication Cause
- Page 107 and 108: Observation Fault indication Cause
- Page 109 and 110: 106 Maintenance Emotron AB 014135-0
- Page 111 and 112: 12.3.1 Cable kit for external curre
- Page 113 and 114: 110 Options Emotron AB 01-4135-01r2
- Page 115: Table 19Typical motor power at main
- Page 119 and 120: 13.2 General electrical specificati
- Page 121 and 122: Table 25Power lossesModelPower loss
- Page 123 and 124: 13.5 Derating at highertemperatureB
- Page 125 and 126: 13.9 Semi-conductor fusesAlways use
- Page 127 and 128: Table 27Parameter listMenuno.Functi
- Page 129 and 130: Table 27Parameter listMenuno.Functi
- Page 131 and 132: Table 27Parameter listMenuno.Functi
- Page 133 and 134: Table 27Parameter listMenuno.Functi
- Page 135: Operation R .......................
- Page 138: Emotron AB, Mörsaregatan 12, SE-25