Emotron MSF 2.0 Softstarter

More documents

Recommendations

Info

12. OptionsThe following options are available. Please contact your supplierfor more detailed information.12.1 Serial communicationFor serial communication the MODBUS RTU (RS232/RS485) option board is available, order part number: 01-1733-00. The softstarter MSF 2.0 can also be ordered withthe MODBUS RTU (RS232/RS485) option mounted, forordering information see chapter 1.5 page 512.3 External control panelThe external control panel option is used to move the controlpanel from the softstarter to the front of a panel door orcontrol cabinet.The maximum distance between the softstarter and theexternal control panel is 3 m.The part number to order for the external control panel is01-3060-00. A separate data sheet for this option is available.The softstarter MSF 2.0 can also be ordered with theexternal control panel mounted, for ordering informationsee chapter 1.5 page 5Fig. 70 Option RS232/48512.2 Fieldbus systemsVarious option boards are available for the following bus systems:• PROFIBUS DP order part number: 01-1734-01• Device NET, order part number: 01-1736-01Each system has its own board. The option is delivered withan instruction manual containing all the details for theinstallation and set-up of the board and the protocol for programming.The softstarter MSF 2.0 can also be ordered witha fieldbus option mounted, for ordering information seechapter 1.5 page 5Fig. 72 Use of the external control panel.Fig. 71 Profibus OptionEmotron AB 01-4135-01r2 Options 107
12.3.1 Cable kit for external currenttransformersThis kit is used for the bypass function, to connect the currenttransformers externally. order part number: 01-2020-00.33±0.56083.5Fig. 73 Cable kit12.4 Terminal clampData: Single cables, Cu or AlCables 95-300 mm 2MSF type Cu Cable 310Bolt for connection to busbar M10Dimensions in mm33x84x47 mmPart no. single 9350Data: Parallel cables, Cu or AlCables 2x95-300 mm 2MSF type and Cu Cable 310 to 835Bolt for connection to busbar M10Dimensions in mm35x87x65Part no. parallel 935141±0.54770-300 mm41±0.2652x95-300 mmFig. 74 The terminal clamp.5886.530±0.535±0.530±0.5108 Options Emotron AB 01-4135-01r2
Page 1 and 2:
Emotron MSF 2.0SoftstarterInstructi
Page 4 and 5:
Safety instructionsSafetyThe softst
Page 6 and 7:
ContentsSafety instructions .......
Page 8 and 9:
1. General informationThis manual d
Page 10 and 11:
1.8 Glossary1.8.1 AbbreviationsIn t
Page 12 and 13:
2. DescriptionT/T nn/n sIn this cha
Page 14 and 15:
The disadvantage of the star-delta
Page 16 and 17:
T/T n2,521,510,5Torquef 3
Page 18 and 19:
3. MountingThis chapter describes h
Page 20 and 21:
Mounting schemesMSF-017 to MSF-250T
Page 22 and 23:
4. ConnectionsThe description of in
Page 24 and 25:
Fig. 20 Connection of MSF-110 to MS
Page 26 and 27:
Fig. 22 Connection of MSF-310 to MS
Page 28 and 29:
4.3 Minimum wiringThe figure below
Page 30 and 31:
5. How to get startedThis chapter b
Page 32 and 33:
5.5 Setting the start commandAs def
Page 34 and 35:
6. Applications and functions selec
Page 37 and 38:
Table 10Applications Rating ListApp
Page 39 and 40:
Table 11Application Functions ListA
Page 41 and 42:
38 Applications and functions selec
Page 43 and 44:
The control panel is used for selec
Page 45 and 46:
7.7 Overview of softstarteroperatio
Page 47 and 48:
8.1 General settingsGeneral setting
Page 49 and 50:
Nominal motor speed.2 1 314Nominal
Page 51 and 52:
Overload time (s)Normal loadInterna
Page 53 and 54:
NOTE: Check that the motor current
Page 55 and 56:
8.4.3 Reset to factory setting [243
Page 57 and 58:
External alarm auto reset [257]This
Page 59 and 60: With voltage control the output vol
Page 61 and 62: To optimize the start, use the sett
Page 63 and 64: Torque boost current limit [316]In
Page 65: NOTE: For several start/stops it is
Page 68 and 69: Slow speed controlled by an externa
Page 70 and 71: JOG commands can be given via analo
Page 72 and 73: Power Factor Control PFC [341]Durin
Page 74 and 75: Max power alarm [400]In this menu m
Page 76: Min power alarm response delay [410
Page 79 and 80: Undervoltage level [437]This menu i
Page 81 and 82: Relay outputsPTC inputPTCCurrent tr
Page 83 and 84: Analogue start/stop off-value [503]
Page 85 and 86: Digital input 3 function [512]In th
Page 87 and 88: Scaling analogue output, max [523]T
Page 89 and 90: K1 contact function [533]In this me
Page 91 and 92: !CAUTION: Very high currents can ar
Page 93 and 94: For applications which use the reve
Page 95 and 96: It is possible to use just one digi
Page 97 and 98: Line main voltage L1-L38.10.2 Statu
Page 99 and 100: 8.11 Alarm listThe alarm list is ge
Page 101 and 102: whether they need a Reset signal (m
Page 103 and 104: 100 Protection and alarm Emotron AB
Page 105 and 106: Observation Fault indication Cause
Page 107 and 108: Observation Fault indication Cause
Page 109: 106 Maintenance Emotron AB 014135-0
Page 113 and 114: 110 Options Emotron AB 01-4135-01r2
Page 115 and 116: Table 19Typical motor power at main
Page 117 and 118: Table 21Typical motor power at main
Page 119 and 120: 13.2 General electrical specificati
Page 121 and 122: Table 25Power lossesModelPower loss
Page 123 and 124: 13.5 Derating at highertemperatureB
Page 125 and 126: 13.9 Semi-conductor fusesAlways use
Page 127 and 128: Table 27Parameter listMenuno.Functi
Page 135: Operation R .......................
Page 138: Emotron AB, Mörsaregatan 12, SE-25
show all

Emotron MSF 2.0 Softstarter

Create successful ePaper yourself

Delete template?

Save as template?