Ordering Information - Equinsa Networking

Table of contents4 FutureCom E4.1. System Descriptions & Data 564.2. Cable4.2.1. Cat. 7 S/FTP 900/23 and S/FTP 600/23 Cable 614.2.2. Cat. 6 S/FTP 450/23 Cable 644.2.3. Cat. 6 F/FTP 450/23 Cable 664.3. Connecting Hardware4.3.1. S250 Module Overview 684.3.2. Certificate for S250 Module 694.3.3. S250 Module 704.3.4. S250 fx Module 714.4. Hardware4.4.1. S250 Outlets and Patch Panel 724.4.2. S250 Double Module Outlet 734.4.3. Installation Options for Outlets 744.5. Patch Cords4.5.1. Cat.6 Patch Cords 754.5.2. Consolidation Point Patch Cords 764.6. Plug & Play 774.7. Test Cable 79FutureCom 10 TENFutureCom EFutureCom DFutureCom UEFutureCom UDHardwareTelephone /ISDN ProductsFurtherInformationSpecialCableIndustrialCableFlex Wire Cablefor Patch CordFutureCom F IntroductionCorning Cable Systems55

FutureCom E SystemFutureCom E is Corning’s proven system solution for symmetrical cabling. It exceeds all requirements of the current ISO/IEC11801 (2002) and EN 50173-1 (2003) standards, Class D and E links and Categories 5 and 6 for components. In addition, theFutureCom E system also satisfies Category 5e according to TIA/EIA-568-A-5.Face Plate“DELTAprofil”,80x80 mmWAXWSE-00001-C001and S250 outlet,2xRJ45,Cat.6, inclined,CAXESD-S0201-C001FutureComS/FTP 600/23CCXEDB-F0047-C001-L7S250 Module,1 x RJ45,shielded, Cat. 6CAXESM-00100-C001S/FTP flex/26, blue,2xRJ45- connectors,4 pairs,for10/100/1000 Base-TCCAEGB-G2002-A020-C0S/FTP flex/26, blue,2xRJ45 connectors,4 pairs,for 10/100/1000Base-TCCAEGB-G2002-A020-C019“ Patch Panel,formax. 24 LANscape®modules,with integrated cablestrain relief, 1 U,front panel ofhigh-grade steelWAXWSV-02400-C001A very high level of system performance is achieved for thelink through the use of high-quality Category 6 connectiontechnology, Category 6 and 7 cables and Category 6 patchcords. The resulting performance and the future securityguaranty maximum investment protection.The system is suitable for all recognized standardized voiceand data transmission procedures. This applies to analogvoice transmission, ISDN,Token Ring, Ethernet (10/100Base-T),Ethernet (100Base-TX) and Gigabit Ethernet (1000Base-T)and for future high bit-rate transmission procedures.Fully configured with a RJ45 connector and RJ45 module, thecabling can be used universally and is application-neutral.The performance of the FutureCom E cabling system hasbeen certified by an independent testing body (see certificate).Of course, all standardized EMC threshold values inEurope are observed.56 Corning Cable Systems

FutureCom E System DataFar-end Crosstalk Relatingto the Far End (ELFEXT)ELFEXT in dB(typ. FutureCom E values)Min. ELFEXT in dBAccording to standardFrequency in MHzReturn LossReturn loss in dB(typ. FutureCom E values)min. Return loss in dBAccording to standardFrequency in MHzTest SetupFutureCom E Test Cable, 2xRJ45, 3 mS250 Module, 2xRJ4590 m FutureCom S/FTP900/23S250 Patch Panel 19“FutureCom E Test Cable, 2 x RJ45, 3 mNominal intrinsic impedanceMax. DC loop resistance (according to standard)DC loop resistance (typ. FutureCom E values)Max. delay (according to standard)Max. delay (typ. FutureCom E values)100 40 18 0.05 µs 0.02 µs58 Corning Cable Systems

FutureCom E Certificate4-Connector ChannelFurtherInformationSpecialCableIndustrialCableFlex Wire Cablefor Patch CordTelephone /ISDN ProductsHardwareFutureCom UDFutureCom UEFutureCom DFutureCom EFutureCom 10 TENFutureCom F IntroductionCorning Cable Systems59

FutureCom E Certificate3-Connector Permanent Link60 Corning Cable Systems

FutureCom E Cat. 7+ and Cat.7 CablesS/FTP 900/23 and S/FTP 600/23FurtherInformationFutureCom DFutureCom EFutureCom 10 TENFutureCom F IntroductionBraided shieldHalogen-free jacket,flame retardantTwisted pairApplicationThe FutureCom S/FTP 900/23 and S/FTP 600/23 cables aredesigned for applications up to 1000/800 MHz and theirtransmission characteristics exceed Category 7 specifications.FutureCom UEFutureCom UDFoil shielding (PiMF)4 shielded pairsPE foam-skin insulationCopper conductorAWG 23FutureCom cables are low-skew products. This is increasinglyrequired for applications above 1 Gigabit-Ethernet. Thesuitability of the cable for utilization up to the GHz areaenables the highest possible transmission speeds in futureproofnetworks. These cables have a streamlined constructionand low weight.Each pair is individually shielded (PiMF). The stranded pairsare additionally braid shielded (S/FTP) which guaranteesoutstanding shielding characteristics. The cable satisfiesClass B interference radiation standards (EN 55022) as wellas immunity (EN 55024) which enables the realization ofCE-compatible networks.HardwareTelephone /ISDN ProductsFlex Wire Cablefor Patch CordIndustrialCableThe FutureCom S/FTP 900/23 and 600/23 cables are alsoavailable in a triplex version. The compact constructionallows flat as well as folded installation.SpecialCableCorning Cable Systems61

FutureCom E Cat. 7+ and Cat.7 CablesS/FTP 900/23 and S/FTP 600/23FeaturesS/FTP 900/23 specified up to 1000 MHz,S/FTP 600/23 specified up to 800 MHzOutstanding electrical characteristicsEasy and convenient installation on double and tripleoutletsCompact installation of the triple cable either flat orfolded (øonly 16.3 mm)Each pair is individually foil shieldedFull braid shieldLow skew between the pairsHalogen-free (LSZH)Flame retardant according to IEC 60332-3, Category CNon-corrosive according to IEC 60754-2 (FRNC)Low smoke according to IEC 61034Mechanical CharacteristicsElectrical Characteristics (at 20°C)Conductor insulationOuter jacketArea/range of applicationTemperature range (installation)Operating temperatureMin. bending radiusfor one-time bendingMin. bending radius duringinstallationCopper conductorHalogen-freeFoam-skin materialHalogen-free,flame retardantDry anddamp rooms0 to +50°C-20 to +60°C>_ 40 mm (for 2 or 3x(4x2...) over flat side)>_ 60 mm (for 2 or 3x(4x2...) over flat side)AWG 23Largest resistance marginInsulation resistanceImpedance Zo at 0.064 MHzImpedance Zo at 1 - 100 MHzImpedance Zo at 101 - 250 MHzImpedance Zo at 251 - 600 MHzSurface transfer impedanceUnbalance to ground dB/BZL = 1000 mUnbalance to ground dB/BZL = 100 mUnbalance to ground dB/BZL = 100 mPropagation velocityat > 10 MHz (NVP x c)Propagation delay >_ 10 MHzDelay skew1%>5000 m x km125 +/– 20%100 +/– 15%100 +/– 18%100 +/– 25%46 dB at 64 kHz>40 dB at 1 MHz>20 dB at 100 MHz0.79 x c4.2 ns/m4 ns/100 m62 Corning Cable Systems

FutureCom E Cat. 7+ and Cat.7 CablesS/FTP 900/23 and S/FTP 600/23Electrical Characteristics (at 20°C) for S/FTP 900/23Frequency in MHzAttenuation in dB/100m *Typical values dB/100mNEXT in dB at 100 m *Typical values in dB at 100 mPSNEXT in dB at 100 m *Typical values in dB at 100mELFEXT in dB at 100 m *Typical values in dB at 100mPSELFEXT in dB at 100 m *Typical values in dB at 100m12.01.780.0>100.0 >100.0 >100.0 >100.0 >100.0 >100.0 >100.0 96.077.098.080.093.077.091.0105.75.080.077.098.074.093.071.091.0167.26.580.077.098.069.993.066.991.0ACR in dB98.3 95.0 93.5 92.7 90.8 86.8 83.2 66.0 49.5 31.0 24.0* Standard: Requirements on 100 m of installed Category 7 cable for Class E/F cabling sections (conforms with EN 50288-4-1)Electrical Characteristics (at 20°C) for S/FTP 600/23Frequency in MHzAttenuation in dB/100m *Typical values dB/100mNEXT in dB at 100 m *Typical values in dB at 100mPSNEXT in dB at 100 m *Typical values in dB at 100mELFEXT in dB at 100 m *Typical values in dB at 100mPSELFEXT in dB at 100 m *Typical values in dB at 100mACR in dBOrdering InformationType designationCategory No. of Pairs12.01.780.0Fire Load(MJ/m)208.17.380.077.098.068.093.065.091.031.2510.19.280.077.098.064.190.061.188.062.514.513.275.172.598.058.186.055.184.010018.516.872.469.498.054.083.051.081.0Max.HalogenfreeStrength(N) (mm)Tensile Outer Weight(kg/km)30033.330.065.362.394.044.568.041.566.0>100.0 >100.0 >100.0 >100.0 >100.0 >100.0 99.077.098.080.093.077.091.098.3105.75.080.077.098.074.093.071.091.095.0* Standard: Requirements on 100 m of installed Category 7 cable for Class E/F cabling sections (conforms with EN 50288-4-1)167.26.580.077.098.069.993.066.991.093.5208.17.380.077.098.068.093.065.091.092.731.2510.19.280.077.098.064.190.061.188.090.862.514.513.275.172.598.058.186.055.184.086.810018.516.872.469.497.054.083.051.081.082.1Length(m)60048.942.560.892.057.890.038.451.035.449.030033.330.765.395.062.393.044.568.041.566.064.3900–55.0–86.0–84.0––––60048.944.060.891.057.889.038.451.035.449.047.0Order Number1000–59.0–83.0–81.0––––800–53.0–87.0–85.0––––34.0FutureCom F IntroductionFutureCom 10 TENFutureCom EFutureCom DFutureCom UEFutureCom UDHardwareTelephone /ISDN ProductsFlex Wire Cablefor Patch CordS/FTP 900/23 4PS/FTP 900/23 4PS/FTP 900/23 8P7+7+7+4480.630.631.26YesYesYes1541543087.77.77.7x16.56464130S/FTP 900/23 12P 7+ 12 1.89 Yes 462 7.7x25.0 195S/FTP 600/23 4PS/FTP 600/23 4PS/FTP 600/23 8P7774480.630.631.26YesYesYes1541543087.77.77.7x16.56464130S/FTP 600/23 12P 7 12 1.89 Yes 462 7.7x25.0 195* X2 cables are delivered in a Reelex box. All other cables are delivered on disposable reels.10002505005001000250500500CCXEDB-I0047-C001-L7CCXEDB-I0047-C001-X2*CCXEDB-I0087-C001-L6CCXEDB-I0127-C001-L6CCXEDB-F0047-C001-L7CCXEDB-F0047-C001-X2*CCXEDB-F0087-C001-L6CCXEDB-F0127-C001-L6IndustrialCableSpecialCableFurtherInformationCorning Cable Systems63

FutureCom E Cat. 6 CablesS/FTP 450/23Braided shieldHalogen-free jacket,flame retardantTwisted pairFoil shielding (PiMF)4 shielded pairsPE foam-skin insulationCopper conductorAWG 23ApplicationThe FutureCom S/FTP 450/23 cables are designed forapplications of up to 600 MHz and their transmissioncharacteristics exceed Category 6 specifications.FutureCom cables are low-skew products, i.e. the skewbetween the individual pairs are very low. This is increasinglyrequired for Gigabit-Ethernet. These cables have astreamlined construction and low weight.Each pair is individually shielded (PiMF). The stranded pairsare additionally braid shielded (S/FTP), which guaranteesoutstanding shielding characteristics. The cables satisfiesClass B interference radiation standards (EN 55022), as wellas immunity (EN 55024), which enables the realization ofCE-compatible networks.Mechanical CharacteristicsFeaturesConductor insulationOuter jacketArea/range of applicationTemperature range (installation)Operating temperatureMin. bending radiusfor one-time bendingMin. bending radius duringinstallationCopper conductorHalogen-freeFoam-skin materialHalogen-free,flame retardantDry anddamp rooms0 to +50°C-20 to +60°C>_ 40 mm (for 2 x(4x2...) over flat side)>_ 60 mm (for 2 x(4x2...) over flat side)AWG 23S/FTP 450/23, specified up to 600 MHzOutstanding electrical characteristicsEach pair is shielded (PiMF)Full braid shieldStreamlined designLightweightLow skew between the pairsHalogen-free (LSZH)Flame retardant according to IEC 60332-3, Category CNon-corrosive according to IEC 60754-2 (FRNC)Low smoke according to IEC 6103464 Corning Cable Systems

FutureCom E Cat. 6 CablesS/FTP 450/23Electrical Characteristics (at 20°C)Largest resistance marginInsulation resistanceImpedance Zo at 0.064 MHzImpedance Zo at 1 - 100 MHzImpedance Zo at 101 - 250 MHzSurface transfer impedanceUnbalance to ground dB/BZL = 1000 mUnbalance to ground dB/BZL = 100 mUnbalance to ground dB/BZL = 100 mPropagation velocity at > 10 MHz (NVP x c)Propagation delay >_ 10 MHzDelay skew1%>5000 M x km125 +/– 20%100 +/– 15%100 +/– 18%46 dB at 64 kHz>40 dB at 1 MHz>20 dB at 100 MHz0.79 x c4.2 ns/m4 ns/100 mFutureCom F IntroductionFutureCom 10 TENFutureCom EElectrical Characteristics (at 20°C)FutureCom DFrequency in MHzAttenuation in dB/100m *Typical values dB/100mNEXT in dB at 100 m *Typical values in dB at 100 mPSNEXT in dB at 100 m *Typical values in dB at 100mELFEXT in dB at 100 m *Typical values in dB at 100mPSELFEXT in dB at 100 m *Typical values in dB at 100mACR in dB12.11.866.0>100.0 >100.0 >100.0 >100.0 >100.0 97.064.098.066.093.064.091.098.2106.05.359.357.398.05093.04791.094.7* Standard: Requirements on 100 m of installed Category 6 cable for Class E cabling sections (conforms with EN 50288-5-1)Ordering InformationType designationCategory No. of PairsFire Load(MJ/m)167.66.856.254.298.045.993.041.091.093.2208.57.654.852.898.044.093.041.091.092.431.2510.89.651.949.998.040.190.037.188.090.462.515.513.647.445.495.034.186.031.184.083.4Max.HalogenfreeStrength(N) (mm)Tensile Outer Weight(kg/km)10019.917.344.395.042.393.030.083.027.081.077.7Length(m)25033.027.738.390.036.388.022.070.019.068.062.3450–38.0–85.0–83.0–54.0–52.047.0Order Number600–44.8–75.0–73.0–48.0–46.030.2FutureCom UEFutureCom UDHardwareTelephone /ISDN ProductsFlex Wire Cablefor Patch CordFlex Wire Cablefor Patch CordIndustrialCableS/FTP 450/23 4PS/FTP 450/23 4PS/FTP 450/23 8P6664480.570.571.14YesYesYes1451452907.9 557.9 557.5x16.6 1201000250500CCXEDB-D0047-C001-L7CCXEDB-D0047-C001-X2*CCXEDB-D0087-C001-L6SpecialCable* X2 cables are delivered in a Reelex box. All other cables are delivered on disposable reels.FurtherInformationCorning Cable Systems65

FutureCom E Cat. 6 CablesF/FTP 450/23ApplicationFoil shield (FTP)Halogen-free jacket,flame retardantTwisted pairFoil shielding (PiMF)4 shielded pairsAdditional wirePE foam-skin insulationCopper conductorAWG 23The FutureCom F/FTP 450/23 cables are designed forapplications of up to 450 MHz and their transmissioncharacteristics exceed Category 6 specifications.FutureCom cables are low-skew products, i.e. the skewbetween the individual pairs are very low. This is increasinglyrequired for Gigabit-Ethernet. These cables have astreamlined construction and low weight.Each pair is individually shielded (PiMF). The stranded pairsare additionally foil shielded (F/FTP), which guarantees outstandingshielding characteristics. The cables satisfies ClassB interference radiation standards (EN 55022), as well as immunity(EN 55024), which enables the realization of CE-compatiblenetworks.Mechanical CharacteristicsFeaturesConductor insulationOuter jacketArea/range of applicationTemperature range (installation)Operating temperatureMin. bending radiusfor one-time bendingMin. bending radius duringinstallationCopper conductorHalogen-freeFoam-skin materialHalogen-free,flame retardantDry anddamp rooms0 to +50°C-20 to +60°C>_ 40 mm (for 2 x(4x2...) over flat side)>_ 60 mm (for 2 x(4x2...) over flat side)AWG 23F/FTP flex cable, specified up to 450 MHzOutstanding electrical characteristicsEach pair is shielded (PiMF)Full foil shielding and additional copper wireStreamlined designLightweightLow skew between the pairsHalogen-free (LSZH)Fire retardant according to IEC 60332-3, Category CNon-corrosive according to IEC 60754-2 (FRNC)Low smoke according to IEC 6103466 Corning Cable Systems

FutureCom E Cat. 6 CablesF/FTP 450/23Electrical Characteristics (at 20°C)Largest resistance marginInsulation resistanceImpedance Zo at 0.064 MHzImpedance Zo at 1 - 100 MHzImpedance Zo at 101 - 250 MHzSurface transfer impedanceUnbalance to ground dB/BZL = 1000 mUnbalance to ground dB/BZL = 100 mUnbalance to ground dB/BZL = 100 mPropagation velocity at >10 MHz (NVP x c)Propagation delay >_ 10 MHzDelay skew2%>5000 M x km125 +/– 20%100 +/– 15%100 +/– 18%100 m/m at 10 MHz>46 dB at 64 kHz>40 dB at 1 MHz>20 dB at 100 MHz0.79 x c4.3 ns/m4 ns/100 mFutureCom F IntroductionFutureCom 10 TENFutureCom EElectrical Characteristics (at 20°C)FutureCom DFrequency in MHzAttenuation in dB/100m *Typical values dB/100mNEXT in dB at 100 m *Typical values in dB at 100 mPSNEXT in dB at 100 m *Typical values in dB at 100mELFEXT in dB at 100 m *Typical values in dB at 100mPSELFEXT in dB at 100 m *Typical values in dB at 100mACR in dB12.11.866.0>100.064.098.066.093.064.091.098.2106.05.359.3>100.057.398.05093.04791.094.7167.66.856.2>100.054.298.045.993.041.091.093.2208.57.654.8>100.052.898.044.093.041.091.092.431.2510.89.651.9>100.049.998.040.190.037.188.090.462.515.513.647.497.045.495.034.186.031.184.083.410019.917.344.395.042.393.030.083.027.081.077.725033.027.738.390.036.388.022.070.019.068.062.3450–38.0–85.0–83.0–54.0–52.047.0* Standard: Requirements on 100 m of installed Category 6 cable for Class E cabling sections (conforms with EN 50288-5-1)FutureCom UEFutureCom UDHardwareTelephone /ISDN ProductsOrdering InformationType designationCategory No. of PairsFire Load(MJ/m)Max.HalogenfreeStrength(N) (mm)Tensile Outer Weight(kg/km)Length(m)Order NumberFlex Wire Cablefor Patch CordIndustrialCableF/FTP 450/23 4PF/FTP 450/23 4PF/FTP 450/23 8P6664480.570.571.16YesYesYes1051052107.47.47.4x15.550501001000250500CCXDDA-D0047-C001-L7CCXDDA-D0047-C001-X2*CCXDDA-D0087-C001-L6SpecialCable* X2 cables are delivered in a Reelex box. All other cables are delivered on disposable reels.FurtherInformationCorning Cable Systems67

FutureCom EModule OverviewFeaturesFully compatible with all modular LANscape® systemsWide range of installation optionsFew individual componentsHigh-level component densityIndividual shieldingHalogen-freeFire class UL94V-0Optimized construction with printed circuit board forbandwidths of more than 300 MHz1500 connector cycles are possibleProven IDC technology for wires with AWG 24 to AWG 22Module reusable several timesIndividual Components of the S250 ModuleDisassembled S250 Basic ModuleFeaturesWire management using TIA/EIA 568 A/B codingInstallation in pairs(no untwisting of the pairs necessary)Rapid assembly timeEasy handlingCompatible with all FutureCom S/FTP and F/FTP cablesWire Management68 Corning Cable Systems

FutureCom E CertificateCat.6 De-embedded for S250 ModulesFurtherInformationSpecialCableIndustrialCableFlex Wire Cablefor Patch CordTelephone /ISDN ProductsHardwareFutureCom UDFutureCom UEFutureCom DFutureCom EFutureCom 10 TENFutureCom F IntroductionCorning Cable Systems69

FutureCom ES250 ModuleFeaturesEasy and quick to install, no special tools requiredIDC connection (IDC = Insulation Displacement Contacts)High-level component densityUniversal usage in all modular LANscape® andFutureCom componentsCategory 6 (2002), de-embeddedOrdering InformationUnit perOrder Number Description DeliveryCAXESM-00100-C001 S250 Module, 1xRJ45, shielded, Cat.6, 1/1incl. copper conducting tape for installationin LANscape modular patch panels,outlets and floor box solutionsCAXESM-00200-C001 S250 Double Module, 2xRJ45, shielded, Cat.6, 1/1incl. copper conducting tape for installationin LANscape modular patch panels,outlets and floor box solutionsCable Strain ReliefUsing the additional cable strain relief allows increased pulling force on the module housings.Unit perOrder Number Description DeliveryCAXCSN-00000-C001 Additional cable strain relief, 100/1for higher pulling force on shieldedFutureCom modules for solid wire,and for assembly of flexible consolidationpoint cables with FutureCom S10 TEN fx ,S250 fx or U250 fx modules70 Corning Cable Systems

FutureCom ES250 fx ModuleApplicationS250 fx Modules are used for the assembly of flexible cablesor consolidation point cables.FeaturesFully compatible with all modular LANscape® connectinghardwareWide range of installation optionsIndividual shieldingProven IDC technology for AWG 24 and AWG 26 strandedwiresModule reusable several times1500 connector cycles are possibleWire management using A/B printing according toTIA/EIA 568Installation in pairs (no untwisting of the pairs isnecessary)Easy handling and very short assembly timeCategory 6, de-embeddedIndividual components of the S250 fx ModuleFutureCom UE FutureCom D FutureCom E FutureCom 10 TEN FutureCom F IntroductionOrdering InformationAssembled S250 fx Modulewith Additional Cable Strain ReliefRequirements for Consolidation PointsFor the assembly of modules with flexible cables,an additional cable strain relief must be usedCCS patch cords (with RJ45 connectors) are wiredaccording to TIA/EIA 568 B; when using other singleendedpre-terminated connecting cables they should bewired according to the RJ45 connector schemeThe installed solid wire cable should have a lowerattenuation specification than the flexible cableFutureCom UDHardwareTelephone /ISDN ProductsFlex Wire Cablefor Patch CordUnit perOrder Number Description DeliveryCAXESM-00100-C003 S250 fx Module, 1xRJ45, shielded, Cat.6, 1/1especially suitable for consolidation pointcable with AWG 24/26 stranded wires,incl. copper conducting tape andadditional cable strain relief for installation inLANscape hardwareIndustrialCableSpecialCableFurtherInformationCorning Cable Systems71

FutureCom ES250 Outlets and Patch PanelOrdering InformationS250 OutletsUnit perOrder Number Description DeliveryS250 Outlet, 2xRJ45,shielded, Cat. 6, inclined,incl. mounting framewith grounding flaps,central plate 50x50 mmwith designation window,screw-fixed, copperconducting tape(without face plate)CAXESD-S0201-C001 white, RAL 9010 1/1CAXESD-S0202-C001 pearl white, RAL 1013 1/1S250 Patch PanelUnit perOrder Number Description DeliveryCAXESV-02400-C001 S250 Patch Panel 19“, 1/1shielded, Cat. 6, including24 FutureCom S250modules and copperconducting tape,with integratedcable strain relief,1 U, high-grade steelfront panelPatch panel accessories please see page 156.72 Corning Cable Systems

FutureCom ES250 Double Module OutletOrdering InformationUnit perOrder Number Description DeliveryCAXESD-S0200-C001 S250 Double Module Outlet, 1/12xRJ45, Cat. 6, inclined,incl. mounting frame withgrounding flaps andcopper conducting tape(suitable for Rutenbeckcompatiblecentral platesor faceplates)FutureCom F IntroductionFutureCom 10 TENFutureCom EFutureCom UDHardwareTelephone /ISDN ProductsFurtherInformationIndustrialCableSpecialCableFlex Wire Cablefor Patch CordFutureCom UEFutureCom DInstallation OptionS250 Double Module Outlet, 2xRJ45, Cat. 6, inclined,incl. mounting frame and copper conducting tape.CAXESD-S0200-C001For example, mounted with a high grade steel face platefrom JungS250 Double Module Outlet with face plate (Jung)Corning Cable Systems73

FutureCom EOutlet Installation OptionsOption 1: 6-Port Frame Set for the installation of 6LANscape® fiber optic or FutureCom modules, inclined, includingmounting frame and two triple housings with designationwindow and dust protection flaps as well as 151x80mm face plate, white, RAL 9010:WAXWSE-V0601-C001equipped with two S250 modulesCAXESM-00100-C001two black labeling iconsWAXWSE-00008-C001four blue labeling iconsWAXWSE-00004-C001and two blue S/FTP flex/26 Patch CordsCCAEGB-D2002-A030-C06-Port Frame Set, inclinedOption 2: S250 Inclined Outlet with two S250 Modules,white, RAL 9010 in the race-way:CAXESD-S0201-C001equipped with one black labeling iconWAXWSE-00008-C001and one blue labeling iconWAXWSE-00004-C001Built into a Tehalit race-wayS250 Inclined Outlet with two S250 ModulesOption 3: Double Surface Outlet for the mounting of 2 LANscapemodules, inclined, including face plate and doublehousing with designation window and dust protectionflaps, white, RAL 9010:WAXWSE-V0201-C001equipped with two S250 modulesCAXESM-00100-C001one gray labeling iconWAXWSE-00003-C001one green labeling iconWAXWSE-00006-C001and one green S/FTP flex/26 Patch CordCCAEGB-D4002-A020-C0using one surface mount housingWAXWSE-00001-C003... and one “DELTAfläche” face plate2-Port Surface Mount Outlet74 Corning Cable Systems

FutureCom ECat. 6 Patch Cords RJ45 to RJ45DescriptionThe FutureCom E System patch cords consist of Category 6flex cable with shielded RJ45 connectors at both ends. Theflex cables have four individual foil-shielded pairs and fullbraid copper shielding. The zero halogen patch cords (LSZH)are non-corrosive (according to IEC 60754-2), low smoke(according to IEC 61034) and flame retardant (according toIEC 60332-1, Category B). They are available in variouslengths and colors.FutureCom F IntroductionFutureCom 10 TENFeaturesFutureCom ES/FTP flex cable, specified up to 600 MHzApplication-neutral due to using all four pairsMinimum surface transfer impedance(

FutureCom EConsolidation Point Patch CordsDescriptionThe FutureCom E Consolidation Point Patch Cords arefactory terminated cable assemblies with one S250 fxmodule and one RJ45 connector. FutureCom S/FTP flex/26Cable is specified up to 600 MHz and satisfies Category 7transmission characteristics. The CP Patch Cords are suitableto connect LANscape® Consolidation Point Housings to wallor desktop outlets.Ordering InformationOrder Number Description LengthS/FTP flex/26 Patch Cords,4 pairs, application-neutral, FRNC sheath,gray, pre-terminated with one RJ45connector and one S250 fx module, Cat. 6,for example 10/100/1000Base-TCCAEGB-D1052-A050-C0 CP Patch Cords S/FTP flex/26 - 5 5 mCCAEGB-D1052-A100-C0 CP Patch Cords S/FTP flex/26 - 10 10 mCCAEGB-D1052-A150-C0 CP Patch Cords S/FTP flex/26 - 15 15 mCCAEGB-D1052-A200-C0 CP Patch Cords S/FTP flex/26 - 20 20 mOther lengths upon request76 Corning Cable Systems

FutureCom EPlug & Play SolutionsApplicationThe S250 Solution Packages are pre-terminated cables withS250 modules at both ends. They are generally offered withFutureCom S/FTP 900/23 cables. Both modules areequipped with additional cable strain relief, to allow higherpulling forces during insertion (the pulling force is restrictedby the cable only). They enable Plug and Play installationand therefore significantly reduce installation time.FutureCom F IntroductionFutureCom 10 TENFutureCom UEFutureCom UDHardwareTelephone /ISDN ProductsFlex Wire Cablefor Patch CordIndustrialCableSpecialCableFurtherInformationFutureCom DFutureCom EOrdering InformationOrder Number Description LengthSolution Package, S/FTP900/23 cable,4 pairs, FRNC jacket pre-terminatedwith 2 S250 modulesand additional cable strain reliefCCAEDB-D2050-A100-C0 S250 Solution Package S/FTP 900/23 - 10 10 mCCAEDB-D2050-A150-C0 S250 Solution Package S/FTP 900/23 - 15 15 mCCAEDB-D2050-A200-C0 S250 Solution Package S/FTP 900/23 - 20 20 mCCAEDB-D2050-A250-C0 S250 Solution Package S/FTP 900/23 - 25 25 mCCAEDB-D2050-A300-C0 S250 Solution Package S/FTP 900/23 - 30 30 mCCAEDB-D2050-A350-C0 S250 Solution Package S/FTP 900/23 - 35 35 mCCAEDB-D2050-A400-C0 S250 Solution Package S/FTP 900/23 - 40 40 mCCAEDB-D2050-A450-C0 S250 Solution Package S/FTP 900/23 - 45 45 mCCAEDB-D2050-A500-C0 S250 Solution Package S/FTP 900/23 - 50 50 mCCAEDB-D2050-A550-C0 S250 Solution Package S/FTP 900/23 - 55 55 mCCAEDB-D2050-A600-C0 S250 Solution Package S/FTP 900/23 - 60 60 mCCAEDB-D2050-A650-C0 S250 Solution Package S/FTP 900/23 - 65 65 mCCAEDB-D2050-A700-C0 S250 Solution Package S/FTP 900/23 - 70 70 mCCAEDB-D2050-A750-C0 S250 Solution Package S/FTP 900/23 - 75 75 mCCAEDB-D2050-A800-C0 S250 Solution Package S/FTP 900/23 - 80 80 mCCAEDB-D2050-A850-C0 S250 Solution Package S/FTP 900/23 - 85 85 mCCAEDB-D2050-A900-C0 S250 Solution Package S/FTP 900/23 - 90 90 mCorning Cable Systems77

FutureCom EPlug & Play SolutionsApplicationThe S250 Plug and Play Solution has been especially createdfor use in data center applications. This specialassembly consists of six S/FTP 900/23 cables, with a commonFRNC jacket. The cable is pre-terminated with six S250modules at both ends. All modules are equipped with additionalcable strain relief, to allow higher pulling force duringinstallation (the pulling force is restricted by the cable only).They enable rapid Plug and Play installation in data centersand therefore significantly reduce installation time. 100%factory testing reduces failures during installation.Ordering InformationOrder Number Description LengthS250 Plug & Play Solution Package, with6x S/FTP 900/23 cables with commonFRNC jacket, both ends terminatedwith 6 S250 modules,and additional cable strain reliefCCAEDB-D2650-A200-C0 S250 Plug & Play Solution Package, 6x S/FTP 900/23 - 20 20 mCCAEDB-D2650-A300-C0 S250 Plug & Play Solution Package, 6x S/FTP 900/23 - 30 30 mCCAEDB-D2650-A400-C0 S250 Plug & Play Solution Package, 6x S/FTP 900/23 - 40 40 mOther lengths available upon request.Installation OptionS250 Plug & Play Solution Package, with 6x S/FTP 900/23cables with common FRNC jacket, both ends terminatedwith 6 S250 modules, and additional cable strain relief:CCAEDB-D2650-A200-C0installed in a CCHE Empty Panel for 6 LANscape modulesCCHE-CP00-LSCCHE Panel with Plug & Play Solution Package78 Corning Cable Systems

FutureCom EUniversal Test Cord for Channel TestingApplicationThe universal channel test cord can be used for acceptancetests of shielded FutureCom E Systems in conjunction withthe universal test adapter from Fluke or other test devicemanufactureres.One pair of these test cords is required for acceptance tests.Ordering InformationUnits perOrder Number Description DeliveryCCAEGB-D10M0-A030-C0 Universal Test Cord, for the acceptance test 1/1of the FutureCom E System in conjunctionwith the universal test adapter from Flukeor other test device manufacturers,2xRJ45, 4 pairs, 3 mFurtherInformationFutureCom UE FutureCom D FutureCom E FutureCom 10 TEN FutureCom F IntroductionSpecialCableIndustrialCableFlex Wire Cablefor Patch CordTelephone /ISDN ProductsHardwareFutureCom UDCorning Cable Systems79