Super Cub - Hangar 9

More documents

Recommendations

Info

Step 20. Repeat Steps 17 through 19 for the rudder controllinkage. Once the epoxy has cured, reinstall the elevator andrudder control linkages connecting them to the control surfacehorns and respective servo arms. Use the 4-40 nuts and clevisto secure each clevis to the control horns.BA45
Section 14: Attaching the CowlParts Needed• Fuselage assembly• Cowl• Mounting screws (4)• Cowl mounting blocks (4) (Super Cub)Tools and Adhesives Needed• Moto-tool with cut-off wheel and sanding drum• Hobby knife• Felt-tipped pen/pencil• Masking tapeStep 2a. (J-3 Cub) Looking at the firewall notice the plywoodfuselage doublers extending out on both sides of the fuselage.Measure 1" from the top of the doubler and make a mark. Makeanother mark at 3 1 ⁄2" from the top. Measure in 3/8" from thefront of the fuselage at the marks. This will be the location of the4-40 T-nuts. (Go to Step 3a.)AStep 1. Trial fit the cowl to the fuselage. Noting where theengine cylinder head hits the cowl. Use a moto-tool to carefullytrim away the fiberglass to allow the cowl to slide on to thefuselage. Remove the cowl.BStep 2. (Super Cub) Looking at the firewall, notice the plywoodfuselage doublers extending out on both sides of the fuselage.Measure 3/4" from the top of the doubler and make a mark.Make another mark at 3 1 ⁄4" from the top. This will be thelocation of the top of the mounting blocks.Step 3. (Super Cub) Align the top edge of the blocks with themarks made in Step 2. The taller block is in the upper locationand the shorter block in the lower. Trace around the outside ofthe block and carefully remove the covering at each blockslocation. (Go to Step 4.)46
Page 4 and 5: Additional Required Equipment4 chan
Page 6 and 7: Contents of Kit (Super Cub)DA927B81
Page 8 and 9: Step 5. Turn the wing panel over, d
Page 10: Step 5. Use a 1/16" drill bit to dr
Page 13 and 14: Section 4: Mounting the Wing to the
Page 15 and 16: Step 6. With the horizontal stabili
Page 17 and 18: Section 6: Hinging the ElevatorsPar
Page 19 and 20: Section 7: Installing the Rudder an
Page 21 and 22: Step 9. Once the epoxy has cured, d
Page 23 and 24: Step 4. Attach the elevator control
Page 25 and 26: Step 3. Locate the wheel pants, axl
Page 27 and 28: Step 12. Temporarily install the wh
Page 29 and 30: Step 3. Secure the axles to the lan
Page 31 and 32: Section 10: Mounting the EnginePart
Page 33 and 34: Step 4G. The plywood adapter mount
Page 35 and 36: Section 11: Assembly and Installati
Page 37 and 38: Step 11. Feed the marked fuel line
Page 39 and 40: Step 6. Attach the switch to the fu
Page 41 and 42: Step 5. Carefully cut a groove appr
Page 43: Step 14. Locate one of the 6" 4-40
Page 47 and 48: Section 15: Attaching the Windshiel
Page 49 and 50: Section 17: Balancing and ControlTh
Page 51 and 52: 52J-3 and Super CubFront Cabin Floo
Page 53 and 54: 54J-3 and Super CubRear Cabin Floor
Page 55 and 56: © Copyright 2002, Horizon Hobby, I

Super Cub - Hangar 9

Create successful ePaper yourself

Delete template?

Save as template?