Super Cub - Hangar 9

More documents

Recommendations

Info

Additional Required Equipment4 channels (minimum)5 servos (JRPS8101 recommended)Standard 600-1000mAh-receiver battery packY-harness (non-computer radio)Recommended JR Systems:JR XP652JR XP662JR XP783JR XP8103PCM10XJR XP8103JR PCM10xEngine RequirementsRecommended Engines:1.08–1.48 2-cycle engines1.20–1.80 4-cycle enginesZenoah ® G23 gas engineRecommended 2-Cycle Engines:Webra 1.20MDS 1.48MDS 1.48(MDSE14800)Recommended 4-Cycle Engines:Saito 1.20–1.80Saito 1.20GK–1.80GKSaito 1.82 TwinSaito 1.82 Twin(SAIE182)Recommended Gasoline Engine:Zenoah G23Zenoah G23(ZENE23A)5
Other Items Needed (not included in the kit)• Propeller• Pro Fuel filter (HAN143) (for gas or glow fuel)• Servo extensions (2) (JRPA098, 12" HD Gold)and (2) (JRPA102, 24" HD Gold)• Fuel tubing (for gas or glow fuel)• Fuel Filler (HAN115)• Radio packing foam• Shut-off switch for gasoline engine (Kill Switch) (ZEN2000)Also Available for Gas Engine OperationZenoah ®Gas Start Kit (ZEN20002) Includes:• Kill Switch (ZEN20000)• Oil (2 cycle) (ZEN20001)• Fuel Filler (HAN115)• Mix cup (HAN3101)• Gas Stopper (DUB400)• 3’ gas fuel tubing (DUB799)• Fuel Line Clips (DUB677)Tools and Adhesives Needed (not included in the kit)Tools• Drill• Drill Bits: 1/16, 1/8, 5/32• Soldering iron• Phillips screwdriver (small and medium)• Pliers: Z-bend and needle-nose• Moto-tool with sanding drum and cutoff wheel• Hobby knife with #11 blades• Mixing sticks• Epoxy brush• 90-degree triangle• Sanding bar• Sandpaper (medium)• Straight edge• Measuring device (e.g. ruler, tape measure)• Canopy scissors• Paper towels• Rubbing alcohol• Wax paper• Felt-tipped penAdhesives• Thin CA (cyanoacrylate) glue• 6-minute epoxy• 30-minute epoxy• Blue Locktite Z-42• Canopy glue (Formula 560)• Silver solder• Masking tape6
Page 6 and 7: Contents of Kit (Super Cub)DA927B81
Page 8 and 9: Step 5. Turn the wing panel over, d
Page 10: Step 5. Use a 1/16" drill bit to dr
Page 13 and 14: Section 4: Mounting the Wing to the
Page 15 and 16: Step 6. With the horizontal stabili
Page 17 and 18: Section 6: Hinging the ElevatorsPar
Page 19 and 20: Section 7: Installing the Rudder an
Page 21 and 22: Step 9. Once the epoxy has cured, d
Page 23 and 24: Step 4. Attach the elevator control
Page 25 and 26: Step 3. Locate the wheel pants, axl
Page 27 and 28: Step 12. Temporarily install the wh
Page 29 and 30: Step 3. Secure the axles to the lan
Page 31 and 32: Section 10: Mounting the EnginePart
Page 33 and 34: Step 4G. The plywood adapter mount
Page 35 and 36: Section 11: Assembly and Installati
Page 37 and 38: Step 11. Feed the marked fuel line
Page 39 and 40: Step 6. Attach the switch to the fu
Page 41 and 42: Step 5. Carefully cut a groove appr
Page 43 and 44: Step 14. Locate one of the 6" 4-40
Page 45 and 46: Section 14: Attaching the CowlParts
Page 47 and 48: Section 15: Attaching the Windshiel
Page 49 and 50: Section 17: Balancing and ControlTh
Page 51 and 52: 52J-3 and Super CubFront Cabin Floo
Page 53 and 54:
54J-3 and Super CubRear Cabin Floor
Page 55 and 56:
© Copyright 2002, Horizon Hobby, I
show all

Super Cub - Hangar 9

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?