Super Cub - Hangar 9

More documents

Recommendations

Info

Step 7. Cut the axle at the mark made in the previous stepusing a moto-tool and cut-off wheel. Align the outside wheelcollar with the end of the axle and tighten the setscrew. Nextslide the inboard wheel collar against the wheel hub and tightenthe setscrew. The wheel should turn freely with no binding.Repeat Steps 6 and 7 for the opposite wheel.Step 8. Connect the two landing gear wires using the rubberband supplied, carefully doubling the rubber band several times.Clip the landing gear wires into the brackets installed in Step 5.AB31
Section 10: Mounting the EngineParts Needed• Fuselage assembly• Engine mount rails• Plywood engine spacer• 4mm x 30mm screw (8)• 4mm T-nut (4)• 4mm nut (4)• 4mm washer (12)• Nylon throttle pushrod and housing• Nylon clevis w/threaded endsStep 2. Temporarily install the engine to the rails using 4mmscrews, washers and nuts. Hold the mount up to the firewall andmark the locations for the blind nuts. Remove the engine fromthe rails.Tools and Adhesives Needed• Phillips screwdriver• Drill• Drill Bit: 7/32"• Measuring device• 6-minute epoxy• Threadlock• Felt-tipped pen/pencilNote: The J-3 <strong>Cub</strong> comes with oval shaped holes cut outin the firewall to accept the 4mm T-nuts for mounting theengine. This allows for different sized engines to be used.Note that the engine should be mounted inverted.Step 1. Locate the engine mounting rails and associated hardware.Step 3. To install the 4mm T-nuts, use a length of music wirewith an L-bend on one end. Slide a T-nut onto the wire and pullthe wire through the mount hole from inside the fuselage andalign with the marks made previously. To seat the T-nuts in thefirewall, tighten the engine mounting screws. After seating theT-nuts, carefully glue them in place using thin CA. Mount therails to firewall using the plywood spacer between the firewalland the rails, making sure to use Threadlock on the screws.ANote: You may need to elongate the holes in the plywoodplate to accommodate the width of your engine.B32
Page 4 and 5: Additional Required Equipment4 chan
Page 6 and 7: Contents of Kit (Super Cub)DA927B81
Page 8 and 9: Step 5. Turn the wing panel over, d
Page 10: Step 5. Use a 1/16" drill bit to dr
Page 13 and 14: Section 4: Mounting the Wing to the
Page 15 and 16: Step 6. With the horizontal stabili
Page 17 and 18: Section 6: Hinging the ElevatorsPar
Page 19 and 20: Section 7: Installing the Rudder an
Page 21 and 22: Step 9. Once the epoxy has cured, d
Page 23 and 24: Step 4. Attach the elevator control
Page 25 and 26: Step 3. Locate the wheel pants, axl
Page 27 and 28: Step 12. Temporarily install the wh
Page 29: Step 3. Secure the axles to the lan
Page 33 and 34: Step 4G. The plywood adapter mount
Page 35 and 36: Section 11: Assembly and Installati
Page 37 and 38: Step 11. Feed the marked fuel line
Page 39 and 40: Step 6. Attach the switch to the fu
Page 41 and 42: Step 5. Carefully cut a groove appr
Page 43 and 44: Step 14. Locate one of the 6" 4-40
Page 45 and 46: Section 14: Attaching the CowlParts
Page 47 and 48: Section 15: Attaching the Windshiel
Page 49 and 50: Section 17: Balancing and ControlTh
Page 51 and 52: 52J-3 and Super CubFront Cabin Floo
Page 53 and 54: 54J-3 and Super CubRear Cabin Floor
Page 55 and 56: © Copyright 2002, Horizon Hobby, I

Super Cub - Hangar 9

Create successful ePaper yourself

Delete template?

Save as template?