Super Cub - Hangar 9

More documents

Recommendations

Info

Step 4. Turn the fuselage over and repeat the hinge gluingprocess by deflecting the elevators in the opposite direction andagain completely saturating each hinge with thin CA. Wipe awayany excess CA with CA remover/debonder and a paper towel.Allow the CA glue to completely dry.Step 5. Once the CA has dried, check the hinges for securityby trying to pull the elevators from the stabilizer. Use only slightpressure and be sure not to crush the wood structure of thestabilizer or elevator.AB19
Section 7: Installing the Rudder andTail Wheel AssemblyParts Needed• Fuselage assembly• Rudder• CA hinges (4)• Tail wheel assembly w/bushingTools and Adhesives Needed• Thin CA• CA remover/debonder• 6-minute epoxy• Pencil• Sharp hobby knife• Drill• Drill Bit: 3/32"• Pliers• Rubbing alcohol• Paper towelsStep 2. Temporarily install the rudder using the hinges provided.Do not glue the hinges at this time. Hold the tail wheel assemblyup to the fuselage as shown and using a pencil lightly mark thelocation where the wire will insert into the rudder. Also mark thelocation where the tail wheel bushing will insert into the back ofthe fuselage. Remove the rudder.Step 1. Locate the tail wheel assembly. Slide the wire throughthe bushing and using a pair of pliers, make a 90-degree bend1/4" up from the bushing as shown. This portion of the wire willbe inserted into the rudder. The nylon bushing will be insertedinto the back of the fuselage.AStep 3. Use a 3/32" drill bit to drill the rudder following themarks you made in the previous step. Make sure to drill straightinto the rudder. Use a sharp hobby knife to make a notch in thebottom portion of the rudder to accept the tail wheel bushing andallow the rudder to seat properly against the vertical fin.Hint: Use a piece of masking tape on the drill bit as adepth gauge to avoid drilling too deep.ABB20
Page 4 and 5: Additional Required Equipment4 chan
Page 6 and 7: Contents of Kit (Super Cub)DA927B81
Page 8 and 9: Step 5. Turn the wing panel over, d
Page 10: Step 5. Use a 1/16" drill bit to dr
Page 13 and 14: Section 4: Mounting the Wing to the
Page 15 and 16: Step 6. With the horizontal stabili
Page 17: Section 6: Hinging the ElevatorsPar
Page 21 and 22: Step 9. Once the epoxy has cured, d
Page 23 and 24: Step 4. Attach the elevator control
Page 25 and 26: Step 3. Locate the wheel pants, axl
Page 27 and 28: Step 12. Temporarily install the wh
Page 29 and 30: Step 3. Secure the axles to the lan
Page 31 and 32: Section 10: Mounting the EnginePart
Page 33 and 34: Step 4G. The plywood adapter mount
Page 35 and 36: Section 11: Assembly and Installati
Page 37 and 38: Step 11. Feed the marked fuel line
Page 39 and 40: Step 6. Attach the switch to the fu
Page 41 and 42: Step 5. Carefully cut a groove appr
Page 43 and 44: Step 14. Locate one of the 6" 4-40
Page 45 and 46: Section 14: Attaching the CowlParts
Page 47 and 48: Section 15: Attaching the Windshiel
Page 49 and 50: Section 17: Balancing and ControlTh
Page 51 and 52: 52J-3 and Super CubFront Cabin Floo
Page 53 and 54: 54J-3 and Super CubRear Cabin Floor
Page 55 and 56: © Copyright 2002, Horizon Hobby, I

Super Cub - Hangar 9

Create successful ePaper yourself

Delete template?

Save as template?