1998 Buick Riviera Owner's Manual
1998 Buick Riviera Owner's Manual 1998 Buick Riviera Owner's Manual
1. Loosen the two bolts on the inboard edge of theheadlamp assembly. This allows you to pull outthe assembly for more hand clearance whenchanging bulbs.2. Reach into the assemblyand turn the bulb socketone-quarter of a turntoward the center of theengine compartment,while pressing it firmly.3.4.5.6.Remove the wire connector from the bulb bylifting the lock tab and pulling it away from theplastic base.Install the bulb by putting the small tab (D) into thesmall notch in the lamp (E).Turn the bulb socket one-quarter of a turn makingsure the tab is properly engaged in the panel slot.To reassemble, attach the wire connector (A) tothe plastic base making sure the lock tab (B) isover the lock (C).6-33
aaeeThe vehicle should not have any snow, ice or mudattached to it.The vehicle should be fully assembled and all otherwork stopped while headlamp aiming is being done.There should not be any cargo or loading of thevehicle, except it should have a full tank of gas andone person or 160 lbs. (75 kg) on the driver’s seat.Tires should be properly inflated.Rock the vehicle to stabilize the suspension.may flash their high beams at you if your adjustmentis much above plus 0.4 degrees.If you find that the headlamp aiming needs adjustment,follow these steps:Start with the vertical headlamp aim. Don’t try to adjustthe horizontal aim first. Adjustment screws can beturned with an E8 Torx@socket or T15 Torx screwdriver.NOTICE:To make sure your headlamps are aimedproperly, read all the instructions beforebeginning. Failure to follow these instructionscould cause damage to headlamp parts.For the vertical adjustment, state inspection stationsgenerally will allow a reading of plus 0.76 degrees orminus 0.76 degrees from the center of the bubble.It is recommended that the upper limit not exceed plus0.4 degrees from the center of the bubble. Other drivers6-341. Check the vertical aim for each headlamp. Thevehicle must be on level a surface. Turn the verticalaiming screw until the bubble in the level is centeredat 0 (zero).
- Page 223 and 224: If the overheat warning continues,
- Page 225 and 226: 4. Then fill the coolsuit recovery
- Page 227 and 228: Changing a Flat TireIf a tire goes
- Page 229 and 230: Removing the Flat Tire and Installi
- Page 231 and 232: Getting under a vehicle when it is
- Page 233 and 234: 9. Replace the wheel nutswith the r
- Page 235 and 236: Storing the Flat Tire and ToolsI A
- Page 237 and 238: Don’t use your compact spare on o
- Page 239 and 240: 5-34
- Page 241 and 242: 5-36
- Page 244 and 245: 0 Be sure to use the proper nuts, b
- Page 246 and 247: Filling Your TankIGasoline vapor is
- Page 248 and 249: If you get gasoline on yourself and
- Page 250 and 251: Hood ReleasePull the handle inside
- Page 252 and 253: Your vehicle has a 3800 Supercharge
- Page 254 and 255: What Kind of Engine Oil to UseOils
- Page 256 and 257: If none of them is true, use the lo
- Page 258 and 259: ~Supercharger OilUnless you are tec
- Page 260 and 261: Checking the Fluid LevelPark your v
- Page 262 and 263: INOTICE:When adding coolant, is it
- Page 264 and 265: ~~ILOWCOOLANTLEVELAdding CoolantIf
- Page 266 and 267: Windshield Washer FluidWhat to UseW
- Page 268 and 269: What to AddWhen you do need brake f
- Page 270 and 271: Replacing Brake System PartsThe bra
- Page 272 and 273: Bulb ReplacementThe following proce
- Page 276 and 277: Exterior Rear BulbsA2. Now adjust t
- Page 278 and 279: TaillampdRear Thrn SignaVBack-Up La
- Page 280 and 281: Windshield Wiper Blade Replacement3
- Page 282 and 283: When to CheckCheck your tires once
- Page 284 and 285: Buying New TiresTo find out what ki
- Page 286 and 287: Temperature -- A, B, CThe temperatu
- Page 288 and 289: Tire ChainsNOTICE:Use tire chains o
- Page 290 and 291: Special Fabric Cleaning ProblemsSta
- Page 292 and 293: Cleaning the Outside of theWindshie
- Page 294 and 295: Cleaning Aluminum or Chrome Wheels
- Page 296 and 297: ~Appearance Care Materials ChartIPA
- Page 298 and 299: Headlamp WiringThe headlamp wiring
- Page 300 and 301: FuseUsageFuseUsage1Air Bag15Cruise
- Page 302 and 303: Under Rear Seat Fuse BlockFuseUsage
- Page 304 and 305: Fuse22232425262128293031UsageTrunk
- Page 306 and 307: A safety belt that isn’t properly
- Page 308 and 309: Air Conditioning RefrigerantsNot al
- Page 310 and 311: Section 7 Maintenance ScheduleThs s
- Page 312 and 313: Performing maintenance work on a ve
- Page 314 and 315: Maintenance ScheduleI Short TripKit
- Page 316 and 317: I Short Trip/City Maintenance Sched
- Page 318 and 319: I Short Trip/City Maintenance Sched
- Page 320 and 321: I Short Trip/City Maintenance Sched
- Page 322 and 323: 1 Short Trip/City Maintenance Sched
1. Loosen the two bolts on the inboard edge of theheadlamp assembly. This allows you to pull outthe assembly for more hand clearance whenchanging bulbs.2. Reach into the assemblyand turn the bulb socketone-quarter of a turntoward the center of theengine compartment,while pressing it firmly.3.4.5.6.Remove the wire connector from the bulb bylifting the lock tab and pulling it away from theplastic base.Install the bulb by putting the small tab (D) into thesmall notch in the lamp (E).Turn the bulb socket one-quarter of a turn makingsure the tab is properly engaged in the panel slot.To reassemble, attach the wire connector (A) tothe plastic base making sure the lock tab (B) isover the lock (C).6-33