NXIP Data Sheet - Trend Controls

More documents

Recommendations

Info

NXIPData SheetFIRMWARE (Continued)Sensor Modules: The sensor module takes the reading from a real sensor connected input, scales it into engineering units, andchecks the value against alarm levels. Each sensor module has the following parameters:ParameterDescriptionL abel( read/write) String that describes the module.$UnitsValue(read/write) 4 character string indicating the engineering units of the sensor' svalue.( read only) The sensor valueVH igh Alarm Limit (read/write) The value above which a sensor high alarm will be generated.HDefault = 0.High Alarm Delay(read/write) The length of time in minutes that the sensor reading must beDabove the high alarm limit before a sensor high alarm is generated.Can beset in the range 0 to 2730 minutes, default =0.L ow Alarm Limit(read/write) The value below which a sensor low alarm will be generated.LDefault = 0.Low Alarm DelayAlarm Bits(read/write) The length of time in minutes that the sensor reading must beAbelow the low alarm limit before a sensor low alarm is generated.Can be setin the range 0 to 2730 minutes, default =0.(read/write) 8 bits that indicate the current alarm status. 000000LH wherethe low alarmstatus bit and H is the high alarm status bit. 1 = alarm.A larm Enable Bits (read/write) 8 bits that enable/disable the sensor high and sensor low alarms.000000LH where L is the low alarm enable bit and H is the high alarm enablebit. 1 = enabled.Text Comms ParameterSwitch Module: Switch modules enable the status of a digital value to be changed. Each switch module has the followingparameters:ParameterDescriptionL abel( read/write) String that describes the module.$S tatus( read/write) The status of the switch (0 or 1) .STime Module: The time module stores information about the current date and time. The time module has the following parameters:ParameterUser Module: The user module provides the NXIP’s security. The module has a PIN, and a PIN level. Once a PIN has been specifiedwhen a user attempts to make a change a PIN that matches one in the NXIP must be sent to the NXIP. The security is enabled assoon as the user module is set up, and can be disabled by setting the PIN Level to 0. The user module has the following parameters:If the PIN is forgotten, the user can contact Technical Support quoting the generator number and MAC address form the addressmodule for default PIN.ParameterPINDescriptionH ours( read/write) The current value of the hours range 0 to 23.HM inutes( read/write) The current value of the minutes range 0 to 59.ND ay of Month( read/write) The current day of the month range 1 to 31.DM onth( read/write) The current month range 1 to 12.MY ear( read/write) The current year range 0 to 99.YDescription(write only) The 4-digitnumber that must bethat user. Range = 0 to 9999, default = 0.Alarms: If the alarm target address and Lan number are set up the NXIP generates network alarms and sends them to the specifiedaddress as follows:L isentered by the user to log on asP IN Level( read/write) The PIN level for the user module. Range = 0 to 99, default = 0.L%MNText Comms ParameterText Comms ParameterText Comms ParameterPAlarmDescriptionL AN BrokenIndicatesa break in the Lan communications .LAN ChangedLAN OKThe alarm is in the format shown below:A node has gone form or been added to the LanLan communications are restoredD UPLICATE ADDRESS TheNXIP's address is duplicated on the network .Alarm CodeNKBKNKCHNKOKNKDAIQL -Rem LAN From on Lan Where is the network address of the NXIP, and is the Lan number of the NXIP. is the alarm text as in the Alarmcolumn of the table above. is the alarm code as in the Alarm Code column of the table above.The NXIP also generates analogue input sensor alarms the following which are sent to the alarm target address if it is specified.SENSOR FAIL occurred (OUTL), SENSOR FAIL cleared (COUT), INPUT ERROR occurred (READ), INPUT ERROR cleared (O/K). Theyare same format as IQ alarms.10 NXIP Variable Speed Drive Network Interface Data Sheet TA200826 Issue 1/F 5/12/07
Data SheetNXIPDISPOSALCOSHH ASSESSMENT FOR DISPOSAL OF NXIP. No partsaffected.RECYCLING .All plastic and metal parts are recyclable. The printed circuitboard may be sent to any PCB recovery contractor to recoversome of the components for any metals such as gold and silver.WEEE Directive :At the end of their useful life the packaging andproduct should be disposed of using a suitablerecycling centre.Do not dispose of with normal household waste.Do not burn.ORDER CODESNXIPNXIP and Installation InstructionsNote that if the NXIP is to communicate with devices on an IQ current loop network a 3xtend/EINC L is required.COMPATIBILITYSupervisors:Utility software:Displays:Ethernet Nodes:Automatic Addressing:963, 915MDS >v3, 916, IQViewSET v6 (including IP Tool auxiliary software)IQView touch screen network display.Compatible with 3xtend/EINC L or EINCMust not be used in an automatic IP addressing environment.INSTALLATIONThe NXIP is installed in the NX drive by removing the cover, unscrewing the two mounting screws on the front of the control unit,and lifting the lid. The boards are then plugged into slot connector position D or E. The procedure involves:Powering down NX drive. Note that at least 5 minutes must be allowed between powering down the drive andopening the coverPlugging NXIP into NX drivePower up NX driveSet up network address and baud rateConnect to IQ System LanSet up parametersTest systemThis installation procedure is covered by the NXIP IQ System NX Variable Speed Drive Interface Installation Instructions TG200827.CONNECTIONSNX Drive ConnectorConnector for connection to NX Drive using slots D or E.EthernetRJ45100 m(max)RJ45Ethernet hub/switchNote that this cable is not suppliedNXIP Variable Speed Drive Network Interface Data Sheet TA200826 Issue 1/F 5/12/0711
Page 1 and 2: Data SheetNXIPNX Variable Speed Dri
Page 3 and 4: Data SheetNXIPSTRATEGYThe strategy
Page 5 and 6: Data SheetNXIPSTRATEGY (Continued)W
Page 7 and 8: Data SheetNXIPFIRMWARE (Continued)A
Page 9: Data SheetNXIPFIRMWARE (Continued)L

NXIP Data Sheet - Trend Controls

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?