EN7.pdf - WALDNER Inc.

More documents

Recommendations

Info

Secuflow EN7 bench-mounted fume cupboard• for high thermal loadsThe Secuflow is especially successful because it canbe operated with lower extract air volumes, whichmeans considerable saving in energy costs and inthe investment costs for the ventilation system. TheSecuflow is the safest and most ecologically soundvariant.We have developed the Secuflow EN7 to securethese benefits also for working with high thermalloads. Due to its sophisticated supply and extractair flow, the fume cupboard secures safe operationwhen working with thermal loads, whilst retaining allthe benefits of the supportive flow fume cupboardSecuflow.When the laboratory is equipped with SecufowEN7 fume cupboards, the user is ideally equipped forany kind of laboratory work: whether this is normaloperation or working with thermal loads.Secuflow EN7 bench-mounted fumecupboards for high thermal loadsIntended use• For work with high thermal loads in the inside of the fumecupboard (Heat sources of 4 KW per meter inner width of thecupboard)• Protective device for the user, tested in accordance withEN 14175-7:2012• Extraction of fumes, aerosols and dust from the internalworkspace to prevent dangerous amounts of pollutants fromescaping into the laboratory• To prevent the formation of dangerous potentially explosiveatmospheres in the internal workspace• Protection from splashes of hazardous substances• Protection from flying particles, bodies or parts escaping fromthe internal workspace• General fume cupboards constructed in acc. with EN14175 are not suited for use with radioactive substances ormicroorganisms• Not suitable for openly breaking down chemicals• Active supportive flow technology (Secuflow technology)reduces the energy consumption while regulations andstandards are observed• Service outlets for sanitary supply in the rear panel of the internalworkspace• Control units located horizontally on the service rail of thesupport unitTechnical dataDimensions 1200 1500 1800Width [mm] 1200 1500 1800Depth [mm] 900Height [mm 2700Clear width, internal workspace [mm] 1150 1450 1750Clear height, internal workspace [mm] 1550Working height [mm] 900
Standard fume cupboard with heating sourceSecuflow EN7 with heating sourceFlow pattern in the Secuflow EN7 with heating sourceDesign characteristics 1200 1500 1800Supporting constructionSelf-supporting underbench units or H-frame with push-in underbench unitsSash 2 horizontal sashes 3 horizontal sashesMax. number of devices for scaffold points, ø 12 mm to 13 mm 9 12Service modules 2 3ElectricsElectrical supplyFuse box, Sash controller SCExternal sockets in service panelsOptionalSanitary technologySanitary supplyService modules with take-off valves for vacuum, gases and/or waters and integrated sink (PP) as an optionVentilation technology 1200 1500 1800Air flow range without / with thermal load [m³/h] 1) 360 / 600 450 / 750 540 / 900Airflow damper, variable, including detector of sash positionAirflow-Controller ACFunction display with temperature monitoringFAZConnection height [mm] for AC with extract manifold Ø 250 mm 2950Underbench exhaustAs an option, depending on requirements and regulations1)All air volume specifications refer to an opening height of the sash window of 500 mm (test opening in acc. with EN 14175) and the maximum tracer gas values recommended by German Standard (BG Chemie).A maximum admission pressure of 600 Pa should not be exceeded in the case of fume cupboards with airflow dampers. The indicated minimum air exchange rates were determined under specified test conditions in acc.with EN 14175-3. These minimum air exchange rates must be adapted when dimensioning the ventilation system.If on-site extract air monitoring systems or airflow dampers are used, the required air volumes may be different. The operating limitations must be agreed upon with Waldner.Material/surfaceWorktopInternal liningStoneware, Polypropylene, Stainless steel, EpoxyMelamine resin facing, Solid grade laminate, Stoneware
Page 1 and 2: Our new fume cupboards for highther
Page 3: The new standard for working in the
Page 7 and 8: Velocity vectors within the workspa

EN7.pdf - WALDNER Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?