Atmel QTouch Library User Guide
Atmel QTouch Library User Guide Atmel QTouch Library User Guide
Figure 5-38: Selecting New Design3. In the Create New Design Window, give the Project name and Kit Technology(QMatrix in this case) and Number of sensors (Keys/Rotors/Sliders) and click CreateDesign.Figure 5-39 Creating New Design in the AVR QTouch Studio1048207K-AT42-09/11
After Creating Design , the new design mode shows the virtual kit view with sensors thathave been created in some order.Figure 5-40: New Design Sensors in the AVR QTouch Studio4. Now Go to Tools->Pin Configuration Wizard as shown below.Figure 5-41: Selecting the pin configuration wizard5. Pin configuration Window will pop up with the information on the usage of the tool.Click Next to proceed.105
- Page 54 and 55: SNS1 and SNSK1 pins usethe same por
- Page 56 and 57: • It is recommended to disable PU
- Page 58 and 59: Table 4 :List of configurable param
- Page 60 and 61: Number ofchannels requiredfor the a
- Page 62 and 63: 2. The above definitions should be
- Page 64 and 65: NUM_Y_LINES_ROTOR_SLIDER_QT_MAX_NUM
- Page 66 and 67: has Four Comparators (AC0A , AC1A ,
- Page 68 and 69: Note: When using the IAR IDE / comp
- Page 70 and 71: Figure 5-11: Selecting the right co
- Page 72 and 73: SNS1 - SNSK1 & SNS2 -SNSK2QT_NUM_CH
- Page 74 and 75: Selecting the right configurationTh
- Page 76 and 77: Figure 5-20 : Specifying QMatrix ac
- Page 78 and 79: Debug Support in Example applicatio
- Page 80 and 81: Support for different compiler tool
- Page 82 and 83: Maximum number of rotor / sliders s
- Page 84 and 85: Tips on pin assignments for the sen
- Page 86 and 87: ATtiny88)v1g1s2(ATtiny461,ATmega16a
- Page 88 and 89: X0,X1,X2,X3 are on PB0,PB1,PB2,PB3N
- Page 90 and 91: 1. The channel numbers are allocate
- Page 92 and 93: SNSK_array[1][1]=0x00; (SNSK odd ma
- Page 94 and 95: SNSK_array[1][0]=0x14; (SNSK even m
- Page 96 and 97: Figure 5-28: New Design Sensors in
- Page 98 and 99: Figure 5-31: Selecting the MCU for
- Page 100 and 101: Figure 5-34: Selecting the SNS and
- Page 102 and 103: 2. QTOUCH_STUDIO_MASKS needs to be
- Page 106 and 107: Figure 5-42: Start window of the co
- Page 108 and 109: Figure 5-45: Selecting the X,YA,YB,
- Page 110 and 111: The code can be copied using the
- Page 112 and 113: ApplicablereleaseQTouch libraries v
- Page 114 and 115: Device Specific LibrariesIntroducti
- Page 116 and 117: Table 8 Compiler tool chains suppor
- Page 118 and 119: maintains the States of QMatrix, QT
- Page 120 and 121: equired as shown in the case A of F
- Page 122 and 123: Figure 37 QMatrix method schematicQ
- Page 124 and 125: Figure 39 QMatrix API Flow diagram
- Page 126 and 127: CAT Module Pin NameCSA0CSB0CSA1CSB1
- Page 128 and 129: The QTouch method acquisition using
- Page 130 and 131: Host Application codeUsing the init
- Page 132 and 133: Frozen Stop Stop Run Run Run Run On
- Page 134 and 135: Figure 45 Raw acquisition mode API
- Page 136 and 137: Figure 46 GNU Example project usage
- Page 138 and 139: the QTouch Library as QMatrix data
- Page 140 and 141: TOUCH_STATUS_CHANGE 0x0002u Status
- Page 142 and 143: sensor_type_tEnumerationUsesensor_t
- Page 144 and 145: OUT_OF_TOUCHIN_TOUCHCurrently the a
- Page 146 and 147: num_channel_signals uint8_t Length
- Page 148 and 149: touch_at_statusstructureInput / Out
- Page 150 and 151: UseData structure which holds the R
- Page 152 and 153: variable to the Touch library. The
After Creating Design , the new design mode shows the virtual kit view with sensors thathave been created in some order.Figure 5-40: New Design Sensors in the AVR <strong>QTouch</strong> Studio4. Now Go to Tools->Pin Configuration Wizard as shown below.Figure 5-41: Selecting the pin configuration wizard5. Pin configuration Window will pop up with the information on the usage of the tool.Click Next to proceed.105