HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

iLO 2 control of ProLiant BL p-Class server LEDsiLO 2 can monitor BL p-Class servers through POST tracking and the Server Health LED.Server POST trackingFeedback is limited while the server is booting because of the headless nature of the ProLiant BL p-Classservers. iLO 2 provides boot-time feedback by flashing the Server Health LED green during server POST.The LED is set to solid amber if the boot is unsuccessful. The LED is set to solid green at the end of asuccessful boot.After a successful boot, control of the Server Health LED is returned to the server, which can turn the LEDoff or set it to some other color to represent the health of the server hardware.Insufficient power notificationiLO 2 turns the Server Health LED solid red if iLO 2 cannot power on the server because insufficient poweris in the rack infrastructure.ProLiant BL p-Class alert forwardingiLO 2 supports blade infrastructure SNMP traps on a pass-through basis. Reporting of blade infrastructurestatus by iLO 2 does not require operating system support. The alerts (traps) originate from the EnclosureManager and Power Supply Manager and are transmitted to iLO 2. iLO 2 p-Class firmware forwardsinfrastructure alerts as SNMP traps to a correctly configured management console. These alerts allow themonitoring of p-Class alerts to take place in an SNMP management console.p-Class alert forwarding is disabled by default and can be enabled from the SNMP/Insight ManageSettings web page.The following alerts are identified and forwarded by iLO 2:Alert ID Description22005 Enclosure temperature failure22006 Enclosure temperature degradation22007 Enclosure temperature OK22008 Enclosure fan failed22009 Enclosure fan degraded22010 Enclosure fan OK22013 Rack power failure22014 Rack power degraded22015 Rack power supply OK22023 Rack server failed; not enough powerProLiant BladeSystem HP Onboard AdministratorHP BladeSystem Onboard Administrator is the enclosure management processor, subsystem, andfirmware base used to support the HP BladeSystem and all the managed devices contained within theenclosure.You can access iLO 2 through the HP Onboard Administrator iLO option ("iLO option" onpage 101) using the Web Administration (on page 102) link or directly. To log in to iLO 2 directly, seethe "Log into iLO 2 for the first time (on page 15)" section for more information.Using iLO 2 98
Enclosure bay IP addressingDuring the First Time Setup Wizard you are asked to set up your enclosure bay IP addressing. For moreinformation on the complete wizard setup process, see the HP BladeSystem Onboard Administrator UserGuide.The server blade iLO 2 ports and interconnect module management ports can obtain IP addresses on themanagement network in three ways: DHCP address, static IP address or EBIPA. If your network has anexternal DHCP service or if you want to manually assign static IP addresses one by one to the serverblades and interconnect modules, click Skip to bypass this step.The server blade iLO 2 defaults to DHCP addressing, obtained through the network connector of theactive Onboard Administrator. Interconnect modules that have an internal management networkconnection to the Onboard Administrator may also default to DHCP address.The Onboard Administrator GUI lists the IP address for the server blade iLO 2 port and interconnectmodule management portIf your facility prefers static IP address assignment, you can individually change each of the server bladeiLO 2 ports and interconnect module management ports to unique static addresses or use EBIPA to assigna range of static IP addresses to individual server blade and interconnect module bays.When a server blade or interconnect module is inserted into a bay that has EBIPA enabled, thatmanagement port will get the specific static IP address from the Onboard Administrator if that device isconfigured for DHCP.The administrator sets an independent range for server blade bays and interconnect module bays usingthe Onboard Administrator EBIPA setup wizard. The first address in a range is assigned to the first bayand then consecutive bays through the range.For example, if you set the server bay EBIPA range to 16.100.226.21 to 16.100.226.36, the iLO 2 inServer bay #1 will be assigned 16.100.226.21 and the iLO 2 in Server bay #12 is assigned16.100.226.32. If you set the interconnect bay EBIPA range to 16.200.139.51 to 16.209.139.58, theinterconnect module management port in Interconnect bay #1 will be assigned 16.200.139.51 and theinterconnect module management port in Interconnect bay #7 will be assigned 16.200.139.57.Using iLO 2 99
Page 1 and 2:
HP Integrated Lights-Out 2User Guid
Page 3 and 4:
ContentsOperational overview ......
Page 5:
Schema-free HPLOMIG-based setup ...
Page 9 and 10:
iLO 2 overviewiLO 2 Standard provid
Page 11 and 12:
functionality can be provided by va
Page 13 and 14:
A separate network increases the se
Page 15 and 16:
4. Select Network>NIC>TCP/IP, press
Page 17 and 18:
Install iLO 2 device driversThe iLO
Page 19 and 20:
Configuring iLO 2In this sectioniLO
Page 21 and 22:
3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24:
• Scripted virtual media• Apple
Page 25 and 26:
3. Click Add.4. Complete the fields
Page 27 and 28:
Group administrationThe Group Accou
Page 29 and 30:
Parameter Default value Description
Page 31 and 32:
If the iLO 2 installation is comple
Page 33 and 34:
4. Verify that the iLO Management I
Page 35 and 36:
Password guidelinesEncryptionThe fo
Page 37 and 38:
By default, iLO 2 creates a self-si
Page 39 and 40:
necessary security, the following c
Page 41 and 42:
10. Change Certificate Owner Field
Page 43 and 44:
Owner Field is set to SAN, iLO 2 ob
Page 45 and 46:
The test page displays the results
Page 47 and 48: To change network settings for iLO
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53 and 54: • Verify NSLOOKUP correctly resol
Page 55 and 56: On select p-Class blades in enclosu
Page 57 and 58: Subnet Mask—Assigns the subnet ma
Page 59 and 60: This configuration causes the iLO 2
Page 61 and 62: Using iLO 2In this sectioniLO 2 bro
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66: Temperaturesfan failure, some fan o
Page 67 and 68: DiagnosticsThe iLO 2 processor reco
Page 69 and 70: The status of these self-tests is i
Page 71 and 72: Remote Console Information screenRe
Page 73 and 74: Supported hot keysThe Program Remot
Page 75 and 76: • Ctrl-Alt-Del—Enters the key s
Page 77 and 78: Security informationIf Remote Conso
Page 79 and 80: High-Performance Mouse option. You
Page 81 and 82: Graceful shutdown• No—Server wi
Page 83 and 84: Processor StatesSelecting the Proce
Page 85 and 86: You can access virtual media on a h
Page 87 and 88: Virtual Floppy and USB key drives d
Page 89 and 90: 3. Click Connect.To use an image fi
Page 91 and 92: 4. Click Create. The virtual media
Page 93 and 94: Rack ViewThe Rack View page present
Page 95 and 96: Enclosure informationEnclosure info
Page 97: Power component informationSelectin
Page 101 and 102: Field Possible value DescriptionDNS
Page 103 and 104: BL p-Class and BL c-Class featuresT
Page 105 and 106: • Flexibility—You can create a
Page 107 and 108: 10. Select the certificate authorit
Page 109 and 110: NOTE: When connected through the Di
Page 111 and 112: Schema PreviewThe Schema Preview sc
Page 113 and 114: Management snap-in installerThe man
Page 115 and 116: Snap-in installation and initializa
Page 117 and 118: d. Add users to the role. Click the
Page 119 and 120: MembersAfter user objects are creat
Page 121 and 122: Active Directory Lights-Out managem
Page 123 and 124: e. Repeat the process for several m
Page 125 and 126: Role managed devicesThe Role Manage
Page 127 and 128: To remove any of the entries, highl
Page 129 and 130: Directory-enabled remote management
Page 131 and 132: How directory login restrictions ar
Page 133 and 134: Using DNS-based restrictions can cr
Page 135 and 136: • HP SIM can:• Manage multiple
Page 137 and 138: • Windows® Server 2003• Novell
Page 139 and 140: 1. Click Start and select Programs>
Page 141 and 142: This page determines if the HP Exte
Page 143 and 144: • Role DN—The role distinguishe
Page 145 and 146: NOTE: The feature associated with t
Page 147 and 148: HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?