HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

iLO 2 diagnostic port configuration parametersThe iLO 2 Diagnostic Port on the front of ProLiant BL p-Class servers enables you to access andtroubleshoot server issues by using a diagnostic cable. The iLO 2 Diagnostic Port uses a static IP address.It does not use DHCP to obtain an IP address, register with WINS or dynamic DNS, or use a gateway.The diagnostic port cable should not be left plugged in without an active network connection because itwill cause degraded network performance on the standard iLO 2 network port.In Network Settings, you can configure specific diagnostic port information. For more information onusing the diagnostic port and the diagnostic cable, see to the setup and installation guide for the bladeserver.The following are the fields that can be configured for the Diagnostic Port:• Enable NICIf Enable NIC is set to Yes, the diagnostic port is enabled.• Transceiver Speed Autoselect• Speed• Duplex• IP AddressUse this parameter to assign a static IP address to iLO 2 on your network. By default, the IP addressis assigned by DHCP. By default, the IP address is 192.168.1.1 for all iLO 2 Diagnostic Ports.• Subnet Mask• Use the subnet mask parameter to assign the subnet mask for the iLO 2 Diagnostic Port. Bydefault, the subnet mask is 255.255.255.0 for all iLO 2 Diagnostic Ports.• The use of the Diagnostic Port is automatically sensed when an active network cable is pluggedin to it. When switching between the diagnostic and back ports, you must allow 90 seconds forthe network switchover to complete before attempting connection through the web browser.NOTE: The diagnostic port will not switch over if an active Remote Console session or a firmware update isin progress.Configuring iLO 2 60
Using iLO 2In this sectioniLO 2 browser interface overview............................................................................................................. 61System Status......................................................................................................................................... 61Remote Console ..................................................................................................................................... 69Virtual devices ....................................................................................................................................... 79ProLiant BL p-Class Advanced management............................................................................................... 92ProLiant BladeSystem <strong>HP</strong> Onboard Administrator ....................................................................................... 98iLO 2 browser interface overviewThe iLO 2 browser interface allows easy access to daily tasks. Each tab of the interface groups similartasks for easy navigation and work flow. The typical user will use the System Status, Remote Console, andVirtual Devices screens of the browser interface.The Administration tab is typically used by an advanced or administrative user who must manage users,configure global and network settings as well as configure or enable the more advanced functions of iLO2.Assistance for all iLO 2 options is available by means of the iLO 2 Help option. These links providesummary information about the features of iLO 2 and helpful information for optimizing its operation. Toaccess page-specific help, click the ? on the right side of the browser window.The "Using iLO 2" section covers:• System Status (on page 61)• Remote Console (on page 69)• Virtual devices (on page 79)• Directory Tests (on page 44)System StatusThe following options are available within the System Status tab.Using iLO 2 61
Page 1 and 2:
HP Integrated Lights-Out 2User Guid
Page 3 and 4:
ContentsOperational overview ......
Page 5:
Schema-free HPLOMIG-based setup ...
Page 9 and 10: iLO 2 overviewiLO 2 Standard provid
Page 11 and 12: functionality can be provided by va
Page 13 and 14: A separate network increases the se
Page 15 and 16: 4. Select Network>NIC>TCP/IP, press
Page 17 and 18: Install iLO 2 device driversThe iLO
Page 19 and 20: Configuring iLO 2In this sectioniLO
Page 21 and 22: 3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24: • Scripted virtual media• Apple
Page 25 and 26: 3. Click Add.4. Complete the fields
Page 27 and 28: Group administrationThe Group Accou
Page 29 and 30: Parameter Default value Description
Page 31 and 32: If the iLO 2 installation is comple
Page 33 and 34: 4. Verify that the iLO Management I
Page 35 and 36: Password guidelinesEncryptionThe fo
Page 37 and 38: By default, iLO 2 creates a self-si
Page 39 and 40: necessary security, the following c
Page 41 and 42: 10. Change Certificate Owner Field
Page 43 and 44: Owner Field is set to SAN, iLO 2 ob
Page 45 and 46: The test page displays the results
Page 47 and 48: To change network settings for iLO
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53 and 54: • Verify NSLOOKUP correctly resol
Page 55 and 56: On select p-Class blades in enclosu
Page 57 and 58: Subnet Mask—Assigns the subnet ma
Page 59: This configuration causes the iLO 2
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66: Temperaturesfan failure, some fan o
Page 67 and 68: DiagnosticsThe iLO 2 processor reco
Page 69 and 70: The status of these self-tests is i
Page 71 and 72: Remote Console Information screenRe
Page 73 and 74: Supported hot keysThe Program Remot
Page 75 and 76: • Ctrl-Alt-Del—Enters the key s
Page 77 and 78: Security informationIf Remote Conso
Page 79 and 80: High-Performance Mouse option. You
Page 81 and 82: Graceful shutdown• No—Server wi
Page 83 and 84: Processor StatesSelecting the Proce
Page 85 and 86: You can access virtual media on a h
Page 87 and 88: Virtual Floppy and USB key drives d
Page 89 and 90: 3. Click Connect.To use an image fi
Page 91 and 92: 4. Click Create. The virtual media
Page 93 and 94: Rack ViewThe Rack View page present
Page 95 and 96: Enclosure informationEnclosure info
Page 97 and 98: Power component informationSelectin
Page 99 and 100: Enclosure bay IP addressingDuring t
Page 101 and 102: Field Possible value DescriptionDNS
Page 103 and 104: BL p-Class and BL c-Class featuresT
Page 105 and 106: • Flexibility—You can create a
Page 107 and 108: 10. Select the certificate authorit
Page 109 and 110: NOTE: When connected through the Di
Page 111 and 112:
Schema PreviewThe Schema Preview sc
Page 113 and 114:
Management snap-in installerThe man
Page 115 and 116:
Snap-in installation and initializa
Page 117 and 118:
d. Add users to the role. Click the
Page 119 and 120:
MembersAfter user objects are creat
Page 121 and 122:
Active Directory Lights-Out managem
Page 123 and 124:
e. Repeat the process for several m
Page 125 and 126:
Role managed devicesThe Role Manage
Page 127 and 128:
To remove any of the entries, highl
Page 129 and 130:
Directory-enabled remote management
Page 131 and 132:
How directory login restrictions ar
Page 133 and 134:
Using DNS-based restrictions can cr
Page 135 and 136:
• HP SIM can:• Manage multiple
Page 137 and 138:
• Windows® Server 2003• Novell
Page 139 and 140:
1. Click Start and select Programs>
Page 141 and 142:
This page determines if the HP Exte
Page 143 and 144:
• Role DN—The role distinguishe
Page 145 and 146:
NOTE: The feature associated with t
Page 147 and 148:
HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

Create successful ePaper yourself

Delete template?

Save as template?