HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

3. Configure the enclosure setting. Using the iLO 2 Web interface, select the BL p-Class tab to accessthe Enclosure Static IP Settings. The BL p-Class tab provides a user interface for configuring theenclosure-level static IP addresses.4. Select a reasonable starting IP address, with the last digit(s) of the address corresponding to the baynumber of each blade (example: 192.168.100.1 through 192.168.100.16), to build an easy-toremembernumbering system.5. Reset bay #1, if necessary. The blade in bay #1 must only be reset if you intend the blade to use aStatic IP bay Configuration address by marking the feature enable mask for bay #1. Before resettingthe blade, browse to the Network Settings page, select Enable Static IP Settings and clickApply to force the blade to reboot and use the newly assigned enclosure static IP.If multiple enclosures are deployed at the same time, the process can be repeated easily by moving asingle blade to bay #1 of each enclosure to perform the configuration.Configuring static IP bay settingsStatic IP bay settings are available on the BL p-Class tab and enable you to configure and deploy theblade server. When configuring these settings, you must use the blade in bay 1.The Enable Static IP Bay Configuration Settings checkbox, available on the Network Settings tab (notshown), allows you to enable or disable Static IP Bay Configuration. The new Enable Static IP BayConfiguration Settings option is only available on blade servers. When Static IP Bay Configuration isenabled, all fields except iLO 2 Subsystem Name are disabled. Only Static IP Bay Configuration or DHCPcan be enabled at one time. Disabling both Static IP Bay Configuration and DHCP signals iLO 2 to use auser-defined IP address. The Enable Static IP Bay Configuration Settings option remains disabled if theinfrastructure does not support Static IP Bay Configuration.ProLiant BL p-Class standard configuration parametersBeginning IP Address (Bay 1)—Assigns the starting IP address. All IP addresses must be validaddresses.Ending IP Address (Bay 16)—Assigns the ending IP address. All IP addresses must be validaddresses.Configuring iLO 2 56
Subnet Mask—Assigns the subnet mask for the default gateway. This field may be filled in if eitherStatic IP Bay Configuration or DHCP is enabled. The entire IP address range must conform to the subnetmask.Gateway IP Address—Assigns the IP address of the network router that connects the Remote Insightsubnet to another subnet where the management PC resides. This field may be filled in if either Static IPBay Configuration or DHCP is enabled.ProLiant BL p-Class advanced configuration parametersDomain Name—Enables you to assign the name of the domain in which the iLO 2 will participate.Primary DNS Server—Assigns a unique DNS server IP address on your network.Secondary DNS Server—Assigns a unique DNS server IP address on your network.Tertiary DNS Server—Assigns a unique DNS server IP address on your network.Primary WINS Server—Assigns a unique WINS server IP address on your network.Secondary WINS Server—Assigns a unique WINS server IP address on your network.Static Route #1, #2, and #3 (destination gateway)—Assigns the appropriate static routedestination and gateway IP address on your network (the default IP values are 0.0.0.0 and 0.0.0.0,where the first IP address corresponds to the destination IP, and the second IP address corresponds to thegateway IP).Enabling iLO 2 IP address assignmentThe bay #1 through bay #16 checkboxes enable you to select which BL p-Class blade servers will beconfigured. You can Enable All, Clear All, or Apply your selection.HP BladeSystem setupThe HP BladeSystem setup wizard provides step-by-step instructions to simplify single blade setup withoutrequiring DHCP or PXE. The HP BladeSystem Setup page launches after you authenticate to iLO 2 fromthe front port.The server blade must be properly cabled for iLO 2 connectivity. Connect to the server blade through theserver blade I/O port, while the blade is in the rack. This method requires you to connect the local I/Ocable to the I/O port and a client PC. Using the static IP address listed on the I/O cable label and theinitial access information on the front of the server blade, you can access the server blade through iLO 2through its standard Web browser interface.Although any blade can be used for access, if static IP bay configuration will be used to configure iLO 2network settings, then the first blade in the enclosure should be used for access.The first page of the wizard automatically launches if:• This blade is new from the factory, and you have logged into iLO 2 from the front port.• You did not fully complete the wizard by selecting Finish on the final page, and you did not selectDo not show setup wizard again and clicked Cancel on the beginning page.Configuring iLO 2 57
Page 1 and 2:
HP Integrated Lights-Out 2User Guid
Page 3 and 4:
ContentsOperational overview ......
Page 5: Schema-free HPLOMIG-based setup ...
Page 9 and 10: iLO 2 overviewiLO 2 Standard provid
Page 11 and 12: functionality can be provided by va
Page 13 and 14: A separate network increases the se
Page 15 and 16: 4. Select Network>NIC>TCP/IP, press
Page 17 and 18: Install iLO 2 device driversThe iLO
Page 19 and 20: Configuring iLO 2In this sectioniLO
Page 21 and 22: 3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24: • Scripted virtual media• Apple
Page 25 and 26: 3. Click Add.4. Complete the fields
Page 27 and 28: Group administrationThe Group Accou
Page 29 and 30: Parameter Default value Description
Page 31 and 32: If the iLO 2 installation is comple
Page 33 and 34: 4. Verify that the iLO Management I
Page 35 and 36: Password guidelinesEncryptionThe fo
Page 37 and 38: By default, iLO 2 creates a self-si
Page 39 and 40: necessary security, the following c
Page 41 and 42: 10. Change Certificate Owner Field
Page 43 and 44: Owner Field is set to SAN, iLO 2 ob
Page 45 and 46: The test page displays the results
Page 47 and 48: To change network settings for iLO
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53 and 54: • Verify NSLOOKUP correctly resol
Page 55: On select p-Class blades in enclosu
Page 59 and 60: This configuration causes the iLO 2
Page 61 and 62: Using iLO 2In this sectioniLO 2 bro
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66: Temperaturesfan failure, some fan o
Page 67 and 68: DiagnosticsThe iLO 2 processor reco
Page 69 and 70: The status of these self-tests is i
Page 71 and 72: Remote Console Information screenRe
Page 73 and 74: Supported hot keysThe Program Remot
Page 75 and 76: • Ctrl-Alt-Del—Enters the key s
Page 77 and 78: Security informationIf Remote Conso
Page 79 and 80: High-Performance Mouse option. You
Page 81 and 82: Graceful shutdown• No—Server wi
Page 83 and 84: Processor StatesSelecting the Proce
Page 85 and 86: You can access virtual media on a h
Page 87 and 88: Virtual Floppy and USB key drives d
Page 89 and 90: 3. Click Connect.To use an image fi
Page 91 and 92: 4. Click Create. The virtual media
Page 93 and 94: Rack ViewThe Rack View page present
Page 95 and 96: Enclosure informationEnclosure info
Page 97 and 98: Power component informationSelectin
Page 99 and 100: Enclosure bay IP addressingDuring t
Page 101 and 102: Field Possible value DescriptionDNS
Page 103 and 104: BL p-Class and BL c-Class featuresT
Page 105 and 106: • Flexibility—You can create a
Page 107 and 108:
10. Select the certificate authorit
Page 109 and 110:
NOTE: When connected through the Di
Page 111 and 112:
Schema PreviewThe Schema Preview sc
Page 113 and 114:
Management snap-in installerThe man
Page 115 and 116:
Snap-in installation and initializa
Page 117 and 118:
d. Add users to the role. Click the
Page 119 and 120:
MembersAfter user objects are creat
Page 121 and 122:
Active Directory Lights-Out managem
Page 123 and 124:
e. Repeat the process for several m
Page 125 and 126:
Role managed devicesThe Role Manage
Page 127 and 128:
To remove any of the entries, highl
Page 129 and 130:
Directory-enabled remote management
Page 131 and 132:
How directory login restrictions ar
Page 133 and 134:
Using DNS-based restrictions can cr
Page 135 and 136:
• HP SIM can:• Manage multiple
Page 137 and 138:
• Windows® Server 2003• Novell
Page 139 and 140:
1. Click Start and select Programs>
Page 141 and 142:
This page determines if the HP Exte
Page 143 and 144:
• Role DN—The role distinguishe
Page 145 and 146:
NOTE: The feature associated with t
Page 147 and 148:
HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

Create successful ePaper yourself

Delete template?

Save as template?