HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

3. In the SNMP Alert Destination(s) fields, enter up to three IP addresses that you want to receive theSNMP alerts and select the alert options you want iLO 2 to support.4. Click Apply Settings.Test alerts include an Insight Manager SNMP trap and are used to verify the network connectivity of iLO 2in HP SIM. Only users with the Configure iLO 2 Settings privilege can send test alerts.Be sure you have saved any changes to the SNMP Alert Destination(s) fields before sending a test alert.To send a test alert:1. Select Management in the Administration tab. The SNMP/Insight Manager Settings screenappears.2. Click Send Test Alert in the Configure and Test SNMP Alerts section to generate a test alert andsend it to the TCP/IP addresses saved in the SNMP Alert Destinations fields.3. After generating the alert, a confirmation screen appears.4. Check the HP SIM console for receipt of the trap.Configuring Insight Manager integrationThe Insight Manager Web Agent URL (DNS name or IP address) sets the browser destination of the InsightAgent link on iLO 2 pages. Typically, this link is the IP address or DNS name of the management agentrunning on the host server operating system.Enter the IP address of the host server. The protocol (https://) and port number (:2381) are automaticallyadded to the IP address or DNS name to allow access to the Insight Management Web Agents from iLO2.If the Insight Manager Web Agent URL is set through another method (for example, CPQLOCFG), clickthe refresh button of your browser to display the updated URL.The Level of Data Returned setting controls the content of an anonymous discovery message received byiLO 2. The information returned is used for Insight Manager HTTP identification requests. The followingoptions are available:• Enabled (default) allows Insight Manager to associate the management processor with the hostserver and provides sufficient data to allow integration with .• Disabled prevents iLO 2 from responding to the HP SIM requests.• View XML Reply enables you to examine the data returned at the settings.View the response that will be returned to Insight Manager when it requests Management Processoridentification using this link.To see the results of changes made, click Apply Settings to save the changes. Click Reset Settings toreturn the page to its clear the fields and return to its previous state. The Reset Settings button does notsave any changes.For more information on Insight Agents, click System Status>Insight Agent.ProLiant BL p-Class configurationProLiant BL p-Class servers can be accessed and configured through the:• iLO 2 Diagnostic Port on the front of the server• "Browser-based setup ("Set up using the browser-based option" on page 16)" which initiallyconfigures the system through the iLO 2 Diagnostic Port• Step-by-step installation wizard through HP BladeSystem SetupConfiguring iLO 2 54
On select p-Class blades in enclosures with updated management backplanes that support high-densityblades, iLO 2 can be used for initial enclosure static IP configuration. Initial configuration of the blade inbay 1 allows all subsequent iLO 2s in the enclosure to receive predetermined static IP assignments. Thisfeature is supported in iLO 1.55 and later.ProLiant BL p-Class user requirements• Users must have the Configure iLO 2 Settings privilege.• A network connection to iLO 2 must be available and functioning properly.Static IP bay configurationStatic IP bay configuration, implemented using the new Static IP Bay Settings on the BL p-Class tab, is anoption to ease the initial deployment of an entire enclosure or the subsequent deployment of blades withinan existing enclosure. While the preferred method for assigning IP addresses to the iLO 2 in each bladeserver is through DHCP and DNS, these protocols are not always available on non-production networks.For example, after configuring Static IP Bay configuration for the blade in bay 1, subsequent bladeadditions to the enclosure assume subsequent addresses without DHCP. The network addresses areassigned by blade position bay 1: 192.168.1.1, bay 2: 192.168.1.2, and so on. Deploying subsequentblades does not demand extra configuration, and the network address corresponds to the bay number.Static IP bay configuration automates the first step of BL p-Class blade deployment by enabling the iLO 2management processor in each blade slot to obtain a predefined IP address without relying on DHCP. iLO2 is immediately accessible for server deployment using virtual media and other remote administrationfunctions.Static IP bay configuration uses the Static IP Bay Configuration addressing method, which enables you toassign IP addresses to each iLO 2 based on slot location in the respective server enclosure. By providinga set of IP addresses in the enclosure, you gain the advantages of a static IP bay configuration withoutrequiring each individual iLO 2 to be configured locally.Using iLO 2 static IP bay configuration:• Helps avoid the costs of a DHCP infrastructure to support the blade environment• Provides easier setup with automatic iLO 2 address generation for all or a few selected baysStatic IP Bay Configuration is not supported in G1 BL-series blade enclosures. To view the enclosuregeneration, navigate to the BL p-Class tab, Rack View menu and click Details for a specific enclosure.Static IP Bay configuration is not supported for tan enclosure when Enclosure Type details displays themessage BL Enclosure G1.When a blade is redeployed, Static IP Bay Configuration may not complete as expected. To correct this,verify that the blade is using the current iLO 2 firmware, and then reset the iLO 2 configuration to factorydefaults using iLO 2 RBSU.Configuring a ProLiant BL p-Class blade enclosureTo configure a BL p-Class blade enclosure using static IP bay addressing:1. Install a server blade in bay 1 of the BL p-Class enclosure. The server blade does not need to beconfigured or have an operating system installed. The server blade must be configured beforeinstalling any additional blades in the enclosure.2. Connect a client device to the front-panel iLO 2 port of the blade using the local I/O cable. The localI/O cable connects to the I/O port on the front of the server blade. This connection enables thestatic IP 192.168.1.1 for the iLO 2 Web interface.Configuring iLO 2 55
Page 1 and 2:
HP Integrated Lights-Out 2User Guid
Page 3 and 4: ContentsOperational overview ......
Page 5: Schema-free HPLOMIG-based setup ...
Page 9 and 10: iLO 2 overviewiLO 2 Standard provid
Page 11 and 12: functionality can be provided by va
Page 13 and 14: A separate network increases the se
Page 15 and 16: 4. Select Network>NIC>TCP/IP, press
Page 17 and 18: Install iLO 2 device driversThe iLO
Page 19 and 20: Configuring iLO 2In this sectioniLO
Page 21 and 22: 3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24: • Scripted virtual media• Apple
Page 25 and 26: 3. Click Add.4. Complete the fields
Page 27 and 28: Group administrationThe Group Accou
Page 29 and 30: Parameter Default value Description
Page 31 and 32: If the iLO 2 installation is comple
Page 33 and 34: 4. Verify that the iLO Management I
Page 35 and 36: Password guidelinesEncryptionThe fo
Page 37 and 38: By default, iLO 2 creates a self-si
Page 39 and 40: necessary security, the following c
Page 41 and 42: 10. Change Certificate Owner Field
Page 43 and 44: Owner Field is set to SAN, iLO 2 ob
Page 45 and 46: The test page displays the results
Page 47 and 48: To change network settings for iLO
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53: • Verify NSLOOKUP correctly resol
Page 57 and 58: Subnet Mask—Assigns the subnet ma
Page 59 and 60: This configuration causes the iLO 2
Page 61 and 62: Using iLO 2In this sectioniLO 2 bro
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66: Temperaturesfan failure, some fan o
Page 67 and 68: DiagnosticsThe iLO 2 processor reco
Page 69 and 70: The status of these self-tests is i
Page 71 and 72: Remote Console Information screenRe
Page 73 and 74: Supported hot keysThe Program Remot
Page 75 and 76: • Ctrl-Alt-Del—Enters the key s
Page 77 and 78: Security informationIf Remote Conso
Page 79 and 80: High-Performance Mouse option. You
Page 81 and 82: Graceful shutdown• No—Server wi
Page 83 and 84: Processor StatesSelecting the Proce
Page 85 and 86: You can access virtual media on a h
Page 87 and 88: Virtual Floppy and USB key drives d
Page 89 and 90: 3. Click Connect.To use an image fi
Page 91 and 92: 4. Click Create. The virtual media
Page 93 and 94: Rack ViewThe Rack View page present
Page 95 and 96: Enclosure informationEnclosure info
Page 97 and 98: Power component informationSelectin
Page 99 and 100: Enclosure bay IP addressingDuring t
Page 101 and 102: Field Possible value DescriptionDNS
Page 103 and 104: BL p-Class and BL c-Class featuresT
Page 105 and 106:
• Flexibility—You can create a
Page 107 and 108:
10. Select the certificate authorit
Page 109 and 110:
NOTE: When connected through the Di
Page 111 and 112:
Schema PreviewThe Schema Preview sc
Page 113 and 114:
Management snap-in installerThe man
Page 115 and 116:
Snap-in installation and initializa
Page 117 and 118:
d. Add users to the role. Click the
Page 119 and 120:
MembersAfter user objects are creat
Page 121 and 122:
Active Directory Lights-Out managem
Page 123 and 124:
e. Repeat the process for several m
Page 125 and 126:
Role managed devicesThe Role Manage
Page 127 and 128:
To remove any of the entries, highl
Page 129 and 130:
Directory-enabled remote management
Page 131 and 132:
How directory login restrictions ar
Page 133 and 134:
Using DNS-based restrictions can cr
Page 135 and 136:
• HP SIM can:• Manage multiple
Page 137 and 138:
• Windows® Server 2003• Novell
Page 139 and 140:
1. Click Start and select Programs>
Page 141 and 142:
This page determines if the HP Exte
Page 143 and 144:
• Role DN—The role distinguishe
Page 145 and 146:
NOTE: The feature associated with t
Page 147 and 148:
HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?