HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

If RBSU login is required, then the active configuration menus are controlled by the authenticateduser's access rights.• RBSU Login Not Required (default)Anyone with access to the host during POST may enter the iLO 2 RBSU to view and modifyconfiguration settings. This is an acceptable setting if host access is controlled.iLO 2 Security Override Switch administrationNetworkThe iLO 2 Security Override Switch allows the administrator full access to the iLO 2 processor. This accessmay be necessary for any of the following conditions:• iLO 2 must be re-enabled after it has been disabled.• All user accounts with the Administer User Accounts privilege have been locked out.• A bad configuration keeps the iLO 2 from displaying on the network and RBSU has been disabled.• The boot block must be flashed.Ramifications of setting the Security Override Switch include:• All security authorization checks are disabled while the switch is set.• iLO 2 RBSU runs if the host server is reset.• iLO 2 is not disabled and might display on the network as configured.• iLO 2, if disabled while the Security Override Switch is set, does not log the user out and completethe disable process until the power is cycled on the server.• The boot block is exposed for programming.A warning message is displayed on iLO 2 browser pages indicating that the iLO 2 Security OverrideSwitch is currently in use. An iLO 2 log entry records the use of the iLO 2 Security Override Switch. AnSNMP alert can also be sent upon setting or clearing the iLO 2 Security Override Switch.Setting the iLO 2 Security Override Switch also enables you to flash the iLO 2 boot block. HP does notanticipate that you will need to update the iLO 2 boot block. If an iLO 2 boot block update is everrequired, physical presence at the server will be required to reprogram the boot block and reset iLO 2.The boot block will be exposed until iLO 2 is reset. For maximum security, HP recommends that youdisconnect the iLO 2 from the network until the reset is complete. The iLO 2 Security Override Switch islocated inside the server and cannot be accessed without opening the server enclosure.To set the iLO 2 Security Override Switch:1. Power off the server.2. Set the switch.3. Power on the server.Reverse the procedure to clear the iLO 2 Security Override Switch.Depending on the server, the iLO 2 Security Override Switch might be a single jumper or a specific switchposition on a dip switch panel. To access and locate the iLO 2 Security Override Switch, refer to theserver documentation. The iLO 2 Security Override Switch can also be located using the diagrams on theserver access panel.The Network Settings and DCHP/DNS tabs of the Network section enable you to view and modifynetwork settings for iLO 2.Only users with the Configure iLO 2 Settings privilege can change these settings. Users that do not havethe Configure iLO 2 Settings privilege can view the assigned settings.Configuring iLO 2 46
To change network settings for iLO 2:1. Log in to iLO 2 using an account that has the Configure iLO 2 Settings privilege. ClickAdministration>Network.2. Select Network Settings or DHCP/DNS.3. Change the settings as needed.4. After completing any parameter changes, click Apply to complete the changes.iLO 2 restarts, and the connection of your browser to iLO 2 terminates. To reestablish a connection, wait60 seconds before launching another browser session and logging in.Network SettingsThe Network Settings tab of the Network section displays NIC IP address, subnet mask, and other TCP/IPrelatedsettings. From the Network Settings screen, you can enable or disable DHCP, and you canconfigure a static IP address for servers not using DHCP. All users can view the Network Settings, but onlyusers with the Configure iLO 2 Settings privilege can change these settings.For more information on these parameters, see the HP Integrated Lights-Out Management ProcessorScripting and Command Line Resource Guide.iLO 2 Shared Network PortThe iLO 2 Shared Network Port enables you to choose either the system NIC or the dedicated iLO 2 NICfor server management. When the Shared Network Port is enabled, both regular network traffic andnetwork traffic intended for iLO 2 pass through the system NIC.The Shared Network Port operates using the network port labeled NIC 1 on the rear of the server. NICnumbering within the operating system may vary from the system labeled numbering. The iLO 2 SharedNetwork Port does not incur an iLO 2 performance penalty. Peak iLO 2 traffic is less then 2Mb (on a NICcapable of 1000Mb speeds), and average iLO 2 traffic is infrequent and low.The Shared Network Port is not available on ProLiant ML310 G3, BL20p G4, specific models of theDL320 G3, and all c-class BladeServers.Configuring iLO 2 47
Page 1 and 2: HP Integrated Lights-Out 2User Guid
Page 3 and 4: ContentsOperational overview ......
Page 5: Schema-free HPLOMIG-based setup ...
Page 9 and 10: iLO 2 overviewiLO 2 Standard provid
Page 11 and 12: functionality can be provided by va
Page 13 and 14: A separate network increases the se
Page 15 and 16: 4. Select Network>NIC>TCP/IP, press
Page 17 and 18: Install iLO 2 device driversThe iLO
Page 19 and 20: Configuring iLO 2In this sectioniLO
Page 21 and 22: 3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24: • Scripted virtual media• Apple
Page 25 and 26: 3. Click Add.4. Complete the fields
Page 27 and 28: Group administrationThe Group Accou
Page 29 and 30: Parameter Default value Description
Page 31 and 32: If the iLO 2 installation is comple
Page 33 and 34: 4. Verify that the iLO Management I
Page 35 and 36: Password guidelinesEncryptionThe fo
Page 37 and 38: By default, iLO 2 creates a self-si
Page 39 and 40: necessary security, the following c
Page 41 and 42: 10. Change Certificate Owner Field
Page 43 and 44: Owner Field is set to SAN, iLO 2 ob
Page 45: The test page displays the results
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53 and 54: • Verify NSLOOKUP correctly resol
Page 55 and 56: On select p-Class blades in enclosu
Page 57 and 58: Subnet Mask—Assigns the subnet ma
Page 59 and 60: This configuration causes the iLO 2
Page 61 and 62: Using iLO 2In this sectioniLO 2 bro
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66: Temperaturesfan failure, some fan o
Page 67 and 68: DiagnosticsThe iLO 2 processor reco
Page 69 and 70: The status of these self-tests is i
Page 71 and 72: Remote Console Information screenRe
Page 73 and 74: Supported hot keysThe Program Remot
Page 75 and 76: • Ctrl-Alt-Del—Enters the key s
Page 77 and 78: Security informationIf Remote Conso
Page 79 and 80: High-Performance Mouse option. You
Page 81 and 82: Graceful shutdown• No—Server wi
Page 83 and 84: Processor StatesSelecting the Proce
Page 85 and 86: You can access virtual media on a h
Page 87 and 88: Virtual Floppy and USB key drives d
Page 89 and 90: 3. Click Connect.To use an image fi
Page 91 and 92: 4. Click Create. The virtual media
Page 93 and 94: Rack ViewThe Rack View page present
Page 95 and 96: Enclosure informationEnclosure info
Page 97 and 98:
Power component informationSelectin
Page 99 and 100:
Enclosure bay IP addressingDuring t
Page 101 and 102:
Field Possible value DescriptionDNS
Page 103 and 104:
BL p-Class and BL c-Class featuresT
Page 105 and 106:
• Flexibility—You can create a
Page 107 and 108:
10. Select the certificate authorit
Page 109 and 110:
NOTE: When connected through the Di
Page 111 and 112:
Schema PreviewThe Schema Preview sc
Page 113 and 114:
Management snap-in installerThe man
Page 115 and 116:
Snap-in installation and initializa
Page 117 and 118:
d. Add users to the role. Click the
Page 119 and 120:
MembersAfter user objects are creat
Page 121 and 122:
Active Directory Lights-Out managem
Page 123 and 124:
e. Repeat the process for several m
Page 125 and 126:
Role managed devicesThe Role Manage
Page 127 and 128:
To remove any of the entries, highl
Page 129 and 130:
Directory-enabled remote management
Page 131 and 132:
How directory login restrictions ar
Page 133 and 134:
Using DNS-based restrictions can cr
Page 135 and 136:
• HP SIM can:• Manage multiple
Page 137 and 138:
• Windows® Server 2003• Novell
Page 139 and 140:
1. Click Start and select Programs>
Page 141 and 142:
This page determines if the HP Exte
Page 143 and 144:
• Role DN—The role distinguishe
Page 145 and 146:
NOTE: The feature associated with t
Page 147 and 148:
HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?