HP Integrated Lights-Out 2 User Guide

More documents

Recommendations

Info

• Corporate network where both ports are connected to the corporate network. In thisconfiguration, the server has two network ports (one server NIC, and one iLO 2 NIC) connected to acorporate network.• Dedicated management network where the iLO 2 port is on a separate network.Configure the IP addressThis step is necessary only if you are using a static IP address. When using dynamic IP addressing, yourDHCP server will automatically assign an IP address for iLO 2. HP recommends using DNS or DHCP withiLO 2 to simplify installationTo configure a static IP address, use the iLO 2 RBSU with the following procedure to disable DNS andDHCP and configure the IP address and the subnet mask:1. Restart or power up the server.2. Press the F8 key when prompted during POST. The iLO 2 RBSU runs.3. Select Network>DNS/DHCP, press the Enter key, and then select DHCP Enable. Press thespacebar to turn off DHCP. Be sure that DHCP Enable is set to Off, and save the changes.iLO 2 setup 14
4. Select Network>NIC>TCP/IP, press the Enter key, and enter the appropriate information in theIP Address, Subnet Mask, and Gateway IP Address fields.5. Save the changes.6. Exit iLO 2 RBSU. The changes take effect when you exit iLO 2 RBSU.Log into iLO 2 for the first timeiLO 2 is configured with a default user name, password, and DNS name. Default user information islocated on the iLO 2 Network Settings tag attached to the server containing the iLO 2 managementprocessor. Use these values to access iLO 2 remotely from a network client using a standard Webbrowser.For security reasons, HP recommends changing the default settings after logging in to iLO 2 for the firsttime.The default values are:• User name—Administrator• Password—A random, eight-character, alphanumeric string• DNS Name—ILOXXXXXXXXXXXX, where the Xs represent the serial number of the serverNOTE: User names and passwords are case sensitive.If you enter an incorrect user name and password or a log in attempt fails, iLO 2 imposes a securitydelay. For more information on login security, refer to "Login security (on page 36)."Set up user accountsiLO 2 comes preconfigured with default factory settings, including a default user account and password.For security reasons, HP recommends changing the default settings after logging in to iLO 2 for the firsttime. These changes can be made using any of the iLO 2 user interfaces. RBSU and browser proceduresare explained in this user guide. Other options including the SMASH CLP and scripting methods aredescribed in the "HP Integrated Lights-Out Management Processor Scripting and Command Line ResourceGuide".If iLO 2 is connected to a network running DNS or DHCP, you can use it immediately without changingany settings.Setup using iLO 2 RBSUHP recommends iLO 2 RBSU to initially set up iLO 2 and configure iLO 2 network parameters forenvironments that do not use DHCP and DNS or WINS. RBSU provides the basic tools to configure iLO 2network settings and user accounts to get iLO 2 on the network.You can use RBSU to configure network parameters, directory settings, global settings, and user accounts.iLO 2 RBSU is not intended for continued administration. RBSU is available every time the server is bootedand can be run remotely using the iLO 2 Remote Console.iLO 2 RBSU can be disabled in the Global Settings preferences. Disabling iLO 2 RBSU preventsreconfiguration from the host unless the iLO 2 Security Override Switch is set.To run iLO 2 RBSU to set up local accounts:1. Restart or power up the server.2. Press the F8 key when prompted during POST. The iLO 2 RBSU runs.3. If prompted, enter a valid iLO 2 user ID and password with the appropriate iLO 2 privileges(Administer User Accounts>Configure iLO 2 Settings). Default account information islocated on the iLO 2 Default Network Settings tag attached to the server containing the iLO 2iLO 2 setup 15
Page 1 and 2: HP Integrated Lights-Out 2User Guid
Page 3 and 4: ContentsOperational overview ......
Page 5: Schema-free HPLOMIG-based setup ...
Page 9 and 10: iLO 2 overviewiLO 2 Standard provid
Page 11 and 12: functionality can be provided by va
Page 13: A separate network increases the se
Page 17 and 18: Install iLO 2 device driversThe iLO
Page 19 and 20: Configuring iLO 2In this sectioniLO
Page 21 and 22: 3. Click Upgrade iLO 2 Firmware.4.
Page 23 and 24: • Scripted virtual media• Apple
Page 25 and 26: 3. Click Add.4. Complete the fields
Page 27 and 28: Group administrationThe Group Accou
Page 29 and 30: Parameter Default value Description
Page 31 and 32: If the iLO 2 installation is comple
Page 33 and 34: 4. Verify that the iLO Management I
Page 35 and 36: Password guidelinesEncryptionThe fo
Page 37 and 38: By default, iLO 2 creates a self-si
Page 39 and 40: necessary security, the following c
Page 41 and 42: 10. Change Certificate Owner Field
Page 43 and 44: Owner Field is set to SAN, iLO 2 ob
Page 45 and 46: The test page displays the results
Page 47 and 48: To change network settings for iLO
Page 49 and 50: After iLO 2 resets, the Shared Netw
Page 51 and 52: 5. Navigate to the Virtual LAN ID f
Page 53 and 54: • Verify NSLOOKUP correctly resol
Page 55 and 56: On select p-Class blades in enclosu
Page 57 and 58: Subnet Mask—Assigns the subnet ma
Page 59 and 60: This configuration causes the iLO 2
Page 61 and 62: Using iLO 2In this sectioniLO 2 bro
Page 63 and 64: • Last Used Remote Console displa
Page 65 and 66:
Temperaturesfan failure, some fan o
Page 67 and 68:
DiagnosticsThe iLO 2 processor reco
Page 69 and 70:
The status of these self-tests is i
Page 71 and 72:
Remote Console Information screenRe
Page 73 and 74:
Supported hot keysThe Program Remot
Page 75 and 76:
• Ctrl-Alt-Del—Enters the key s
Page 77 and 78:
Security informationIf Remote Conso
Page 79 and 80:
High-Performance Mouse option. You
Page 81 and 82:
Graceful shutdown• No—Server wi
Page 83 and 84:
Processor StatesSelecting the Proce
Page 85 and 86:
You can access virtual media on a h
Page 87 and 88:
Virtual Floppy and USB key drives d
Page 89 and 90:
3. Click Connect.To use an image fi
Page 91 and 92:
4. Click Create. The virtual media
Page 93 and 94:
Rack ViewThe Rack View page present
Page 95 and 96:
Enclosure informationEnclosure info
Page 97 and 98:
Power component informationSelectin
Page 99 and 100:
Enclosure bay IP addressingDuring t
Page 101 and 102:
Field Possible value DescriptionDNS
Page 103 and 104:
BL p-Class and BL c-Class featuresT
Page 105 and 106:
• Flexibility—You can create a
Page 107 and 108:
10. Select the certificate authorit
Page 109 and 110:
NOTE: When connected through the Di
Page 111 and 112:
Schema PreviewThe Schema Preview sc
Page 113 and 114:
Management snap-in installerThe man
Page 115 and 116:
Snap-in installation and initializa
Page 117 and 118:
d. Add users to the role. Click the
Page 119 and 120:
MembersAfter user objects are creat
Page 121 and 122:
Active Directory Lights-Out managem
Page 123 and 124:
e. Repeat the process for several m
Page 125 and 126:
Role managed devicesThe Role Manage
Page 127 and 128:
To remove any of the entries, highl
Page 129 and 130:
Directory-enabled remote management
Page 131 and 132:
How directory login restrictions ar
Page 133 and 134:
Using DNS-based restrictions can cr
Page 135 and 136:
• HP SIM can:• Manage multiple
Page 137 and 138:
• Windows® Server 2003• Novell
Page 139 and 140:
1. Click Start and select Programs>
Page 141 and 142:
This page determines if the HP Exte
Page 143 and 144:
• Role DN—The role distinguishe
Page 145 and 146:
NOTE: The feature associated with t
Page 147 and 148:
HP Systems Insight Manager integrat
Page 149 and 150:
Clicking on a status icon for iLO 2
Page 151 and 152:
Troubleshooting iLO 2In this sectio
Page 153 and 154:
LED indicatorPOST code(activitycomp
Page 155 and 156:
Event log displayEvent log explanat
Page 157 and 158:
The DHCP server must be configured
Page 159 and 160:
• The use of the diagnostic port
Page 161 and 162:
AlertFailed Login AttemptGeneral Er
Page 163 and 164:
2. On the Level of Privacy screen,
Page 165 and 166:
Terminal Services proxy stops respo
Page 167 and 168:
For example, when User1 logs in, th
Page 169 and 170:
1. Attempt to connect to iLO 2 thro
Page 171 and 172:
Directory services schemaIn this se
Page 173 and 174:
SyntaxOptionsRemarksDistinguished N
Page 175 and 176:
Lights-Out Management specific LDAP
Page 177 and 178:
DescriptionSyntaxOptionsRemarksLoca
Page 179 and 180:
Acronyms and abbreviationsACPIAdvan
Page 181 and 182:
HPONCFGHP Lights-Out Online Configu
Page 183 and 184:
RASremote access serviceRBSUROM-Bas
Page 185 and 186:
IndexAaccess options 23, 28, 33acce
Page 187 and 188:
memory 66Microsoft software 104, 11
Page 189:
virtual media 59, 84, 85, 87, 91, 1
show all

HP Integrated Lights-Out 2 User Guide

Create successful ePaper yourself

Delete template?

Save as template?