DI-50E Data Sheet - K - Tech, Inc.

More documents

Recommendations

Info

Setpoint Programming Mode continuedDeviation (passband) is the programmableband around the setpoint in which thesetpoint can be programmed to energizethe relay inside or outside the deviationband.The deviation setting can be any valuebetween 1 and 65535 counts. The numberof counts selected act both positivelyand negatively on the setpoint, forming adeviation band around the setpoint.For example, if the setpoint setting is 1000 counts and the deviation settingis 35 counts, the deviation band around the setpoint setting is 70counts starting at 965 counts and ending at 1035 counts.Initial Start-up Inhibit.On power-on, start-up inhibit preventsthe relay from energizing on the firstsetpoint activation cycle. Depending onhow the meter has been programmed,initial start-up inhibit either functionsduring a falling input signal, or during arising input signal.Relay Time Control ModesThe following time control mode settings can cover almostevery relay timer application.All setpoints can be individually programmed to operate a relayin one of the following time control modes above or below thesetpoint value.Normal ModeThis mode individuallyprograms a relay’ssetpoint with delayon-make(DOM) anddelay-on-break (DOB)settings.Page 40SP ONSP OFFRLY ONRLY OFFAdj.DOMAdj.DOBNormally OFF / Pulsed ON ModesThese are delay modes were the relay is normally off andpulses on when the setpoint activates.Repeat ON ModeMultiple actuation,programmable on andoff time settings.SP ONSP OFFRLY ONRLY OFFAdj. Adj. Adj.ON-T OFF-T ON-TPulse ON mode (Programmable ON-time)Single actuation, programmableDOM andon time settings.SP ONSP OFFRLY ONRLY OFFAdj.Adj. MAXDOM ON-TDeviation+SP–+SP–SPSPDeviationBandEnergized InsideDeviationBandEnergized OutsideHytseresis+–+–HysteresisBandEnergized BelowHysteresisBandEnergized Above1-Shot ON mode (Programmable Minimum ON-time)SP ONSingle actuation, programmableDOM and SP OFFminimum on timeRLY ONsettings.RLY OFFAdj.DOMNormally ON / Pulsed OFF ModesAdj.MIN ON-TThese are delay modes were the relay is normally on andpulses off when the setpoint activates.1-Shot OFF mode (Programmable Minimum OFF-time)Single actuation, programmableminimumoff time and DOBsettings.SP ONSP OFFRLY ONRLY OFFAdj.DOBAdj.MIN OFF-TTexmate, Inc. Tel. (760) 598-9899 • www.texmate.comPulse OFF mode (Programmable OFF-time)Single actuation, programmableoff timeand DOB.Repeat OFF ModeMultiple actuation,programmable off andon time settings.SP ONSP OFFRLY ONRLY OFFSP ONSP OFF`RLY ONRLY OFFAdj. Adj.DOB MAXOFF-TAdj. Adj. Adj.OFF-T ON-T OFF-TEach setpoint can be individually configured for basic toadvanced operations in the following three levels. Each operationallevel is designed to provide only the required relevantsetpoint and relay functions.The modes at Level 2 and Level 3 can be set to OFF for eachindividual setpoint, ensuring that no other functions are programmedto influence the setup.Level 1Setpoint & Relay Basic ModeThis is an easily programmable mode for users who require thefollowing basic setpoint and relay functions:First Digit – Relay Energize FunctionsRelays programmed to energize above or below thesetpoint value.Second Digit – SP Activation SourceSetpoints programmed to activate from selectablemeter registers or one of six external switched inputs.Third Digit – Setpoint LatchingRelays programmed with latching and manual resetoptions.Level 2Setpoint & Relay Intermediate ModeLevel 2 uses all Level 1 functions and is further extended bythe following programmable modes. The functionality of therelay energize functions are extended by allowing the relaysto be programmed with or without initial start-up inhibit.Hysteresis, Deviation & PID ModeThis mode adds extra functionality to the basic mode by providingprogrammable hysteresis or deviation settings for allsetpoints, or PID control from setpoints SP1 and SP2.Timer ModesThese modes add even more functionality to the basic andintermediate mode by providing each setpoint with a choiceof one of seven resident programmable timers.Level 3Setpoint & Relay Advanced ModeLevel 3 uses all Level 1 and Level 2 functions combined withreset and trigger functions to provide an extremely powerfuladvanced mode.Level 3 enables you to program all setpoints individually foroperations normally requiring sophisticated controllers.21 June, 2004 DI-50 320 Series (NZ300)
Setpoint Programming Mode continuedLevel 1 - Basic Mode - Programming ProceduresExample Procedure:The following procedure describes how to program setpoint 1(SP1) for the following Level 1 setpoint and relay functions:• SP1 to activate from Channel 1 (CH1).• Relay to energize above or below SP1 value.• Relay to latch with manual relay reset.See Setpoints and Relays Supplement (NZ201) for proceduresto program all setpoint and relay operational levels(Level 1 to Level 3). (See page 3 for more information).STARART T HERECONFIGURE LEVEL 1SETPOINT & RELAYFUNCTIONSOperational DisplayProg. SP1 SP2 SP3 SP4 SP5 SP6From Step 5Step 1Enter SetpointProgramming ModePressat sametimePressat sametimeStep 6Select [CH1] as the SP1activation source. Seediagram on Pages 36and 37Prog. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6ORProg. SP1 SP2 SP3 SP4 SP5 SP6Step 2Adjust setpoint 1 (SP1)activation value to e.g.500 countsProg. SP1 SP2 SP3 SP4 SP5 SP6ORStep 7Save SP1control settingsPress1Prog. SP1 SP2 SP3 SP4 SP5 SP6ExampleExampleStep 3Save SP1 activationvalue settingPress6Prog. SP1 SP2 SP3 SP4 SP5 SP6XStep 8Reset 2nd digit to 0. If the 2nddigit is not reset to 0, themeter will constantly cyclethru SPC_1Prog. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6ORProg. SP1 SP2 SP3 SP4 SP5 SP6Step 4Set SPC_1 to [013]:1st DigitProg. SP1 SP2 SP3 SP4 SP5 SP6= 0 Energize above SP1 valueor 1 to energize below SP1 value2nd Digit = 1 Select source for SP13rd Digit = 3 Relay latching with manual resetORStep 9Save SP1control settingsPress1Prog. SP1 SP2 SP3 SP4 SP5 SP6ExampleStep 5Enter SP1source sub-menuPress1Prog. SP1 SP2 SP3 SP4 SP5 SP6To Step 6Step 10Exit SPC_2 and returnto operational displayPressat sametimeProg. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6Pressat sametimeProgramming tipAll required setpoint activation values (SP1 to SP6)can be adjusted before programming setpoint andrelay control function settings. See Setpoint ModeLogic Diagram on Page 42.Prog. SP1 SP2 SP3 SP4 SP5 SP6Operational Display21 June, 2004 DI-50 320 Series (NZ300) Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 41
Page 3 and 4: Tiger 320 Series Modular Literature
Page 6 and 7: Planning to Harness the Power of Ti
Page 8 and 9: SP1 SP2 SP3 SP4 SP5 SP6Planning to
Page 10 and 11: Configuration Utility ProgramThe Ea
Page 12 and 13: Index32-Bit Operating System ......
Page 14 and 15: Controls and IndicatorsFront Panel
Page 16 and 17: SP1 SP2 SP3 SP4 SP5 SP6Front Panel
Page 18 and 19: Front Panel Programming Codes conti
Page 20 and 21: Initial Setup Procedures continuedI
Page 22 and 23: [CAL] - Calibration Modes for Input
Page 24 and 25: [CAL] - Calibration Modes for Input
Page 26 and 27: Initial Setup Procedures[CodE_1] -
Page 38 and 39: SP1 SP2 SP3 SP4 SP5 SP6SP1 SP2 SP3
Page 42 and 43: Setpoint Programming Mode continued
Page 44 and 45: Registers That Can Be Selected By F
Page 46 and 47: Carrier Board Output PinsAnalog Out
Page 48 and 49: 2V20V200VCUSTOMVOFFONON1 2Component
Page 50 and 51: +++0_+0_I-Series Input Signal Condi
Page 52 and 53: ++ONONONI-Series Input Signal Condi
Page 54 and 55: +V++++++++I-Series Input Signal Con
Page 56 and 57: Texmate, Inc. Tel. (760) 598-9899
Page 58 and 59: Ordering Information continued80-MO
Page 60: Case DimensionsPANEL CUTOUTCase wil

DI-50E Data Sheet - K - Tech, Inc.

Create successful ePaper yourself

Delete template?

Save as template?