DI-50E Data Sheet - K - Tech, Inc.

More documents

Recommendations

Info

SP1 SP2 SP3 SP4 SP5 SP6SP1 SP2 SP3 SP4 SP5 SP6Setpoint Programming ModeAll setpoint activation and control settings are selected and configured usingthe front panel buttons in the setpoint programming mode. Or, softwareconfigured via the meter configuration utility program if the meter is connectedto a PC through the serial port. The meter has six software driven setpoints,independently configured to operate within the total span range of themeter and the selected input module.Relay Output ModulesFive standard relay output module options provide a selection of 20 relayconfiguration options for DI-50 meters.Three electromechanical relay output modules support a combination of 5 AForm A and 10 A Form C relays providing 12 configuration options. A solidstate relay (SSR) output module supports 400 V, 210 mA DC SSRs andanother SSR output module supports 400 V, 140 mA AC / DC SSRs providinga further eight configuration options.A 22 opto-isolated I/O plug-in module can support six inputs and up to 16outputs. The standard plug-in module has six inputs and six outputs that canbe extended to 16 outputs with a 10 output add-on board.Prog.Operational DisplaySetpoint Programming ModeTo enter press P andbuttons at the same timeSetpoint Activation Values Mode[SP_1]P[SP_2]PEnter these menus to set setpoint (SP)activation valuesSetpoint 1 Default setting = 18000Setpoint 2Default setting = –18000320 Series Relay Output Module OptionsSSRsElectromechanical RelaysOutput ModuleCarrier Board[SP_3]P[SP_4]Setpoint 3Setpoint 4Default setting = 5000Default setting = –5000PMax Four140 mA(AC/DC)Max Four210 mA(DC Only)Max Four5 A Form AMax Two5 A Form AMax Two10 A Form CMax Six5 A Form A[SP_5]P[SP_6]Setpoint 5Setpoint 6Default setting = 10000Default setting = –10000Optional Opto-isolated22 I/O Plug-in ModuleDigital OutputsAdd-on Board(10 outputs)Mountson topStandard I/OPlug-in Module(6 in/6 out)PSetpoint & Relay Control Settings ModeEnter these menus to configure SPcontrol settingsSetpoint Programming ModeSee the Setpoint Programming Mode Logic Diagram opposite.The setpoint programming mode is entered by pressing the meter’sbuttons at the same time.Setpoint Activation ValuesEach setpoint activation value is individually programmed. Setpoint activationvalues can be set within the total span range of the meter and the selectedinput module.Setpoint and Relay Control SettingsSee the Setpoint and Relay Control Settings diagram on Pages 42 and 43.The control settings provide access to the following setpoint and relay functionsfor configuration using the meter’s 1st, 2nd, and 3rd digits:• 1st Digit – Relay Energize Functions.• 2nd Digit – Setpoint Activation Source.• 3rd Digit – Setpoint Delay, Timer, and Reset and Trigger Functions.Pand[SPC_1]P[SPC_2]P[SPC_3]P[SPC_4]P[SPC_5]P[SPC_6]POperational DisplaySetpoint 1Setpoint 2Setpoint 3Setpoint 4Setpoint 5Setpoint 6See Page 42 fora Level 1 –Setpoint & RelayControl Settingsdiagram.Prog.Setpoint Mode Logic DiagramPage 38Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com21 June, 2004 DI-50 320 Series (NZ300)
*➤Data Data Data Data Data DataData Data Data Data Data DataData Data Data Data Data DataData Data Data Data Data DataData Data Data Data Data DataData Data Data Data Data Data*➤➤➤➤➤➤➤➤➤➤➤Setpoint Programming Mode continuedSPSPAboveACTIVATIONInputChannelsSPSPSPSPSP-BSPSPSPBelowExternal Switched InputsProg. SP1 SP2 SP3 SP4 SP5 SP6SP1SP2SP3SP4SP5SP6RESET SELECTED REGISTERTRIGGER PRINTTRIGGER LOG DATA9SPHysteresis126Pri n t Pri n t3** * **EPS O NT M - U 2 1 0* ** **24: 07: 0 0Job .14322J ob .14322SPSPDataLoggingDeviationRelay Energize FunctionsAll setpoints activate at the setpoint value.All relays/setpoints are programmable toenergize above or below the setpointvalue.LATCHOFFLATCHONTRIGGER OPERATES ON:• MAKE EDGE• BREAK EDGE• MAKE & BREAK EDGE• EVERY SAMPLE PERIODSETPOINT TRACKINGSetpoint Activation SourceSetpoints activate from any inputchannel, selected meter register, orexternal switched inputs (digital inputpins).SPSetpoint LatchingSetpoints can be programmedin relay latching modes.Setpoint Reset & TriggerSetpoints can be programmedto reset selected registers, or bemanually reset. They can alsotrigger a data print or a data log.RESETSP-ASetpoint TrackingSetpoint tracking can beapplied to setpointsconfigured in the hysteresis,deviation, orPID modes.Display FlashingDisplay flashing can be applied to setpoints configured in thehysteresis or deviation modes.Each setpoint can be programmed to make the display flash onand off while the setpoint is active, and keep it flashing until thesetpoint de-activates.Real-time Clock OptionAny setpoint can be programmedto operate from the real-time clockoption.Data LoggingAny setpoint can be programmedto log data within the meter (up to4000 samples).Data Printing to Serial PrinterAny setpoint can be programmedto send data directly to a serialprinter.Data Printing to PCAny setpoint can be programmedto send data directly to a connectedPC.Hysteresis or DeviationEach relay can operate in a hysteresisor deviation mode.SPSPDUAL PID6045 15TIMER30Hysteresis or DeviationEach setpoint can be individuallyprogrammed to energize the relay inthe hysteresis or deviation mode,with or without initial startup inhibit.Hysteresis (deadband) is the programmableband above and belowthe setpoint value that determineswhen and for how long the relay isenergized or de-energized. The setpointcan be programmed to energizethe relay above or below thesetpoint value.PID Control SettingsThe PID (proportional, integral,derivative) control function providesexceptional control stabilityduring control process applica-tions. PID control is available from the following outputs:• Setpoint / relay output.• Analog output.• Relay and analog output at the same time.PID control from the setpoint / relay output is available fromSP1 and SP2 only.There are two PID control outputs available via the analog output:• PID1 – stored in register 50.• PID2 – stored in register 51.PID ControlSetpoints /Relays 1 to 6Analog OutputPID 1 (Reg 50)PID 2 (Reg 51)Timer ModesEach setpoint can be programmed tooperate the relay in one of the followingseven resident timer modes:Normal Mode TimerSingle actuation, delay-on-make (DOM) and delay-onbreak(DOB).Normally OFF/Pulsed ON TimersRepeat ON Mode Timer – multiple actuation, programmableoff- and on-time.Pulse ON Mode Timer – single actuation, programmableDOM and maximum on-time.1-Shot ON Mode Timer – single actuation, programmableDOM and minimum on-time.Normally ON/Pulsed OFF TimersRepeat OFF Mode Timer – multiple actuation, programmableoff- and on-time.Pulse OFF Mode Timer – single actuation, programmableDOB and maximum off-time.1-Shot OFF Mode Timer – single actuation, programmableDOB and minimum off-time.Hytseresis+SP–+SP–HysteresisBandEnergized BelowHysteresisBandEnergized AboveThe hysteresis setting can be any value between 0 and 65535counts. The number of counts selected act both positively andnegatively on the setpoint, forming a hysteresis band aroundthe setpoint.For example, if the setpoint setting is 500 counts and the hysteresissetting is 10 counts, the hysteresis band around thesetpoint setting is 20 counts, starting at 490 counts and endingat 510 counts.Note:If hysteresis is set with ZERO counts, the relay energizesAT or ABOVE the setpoint value.21 June, 2004 DI-50 320 Series (NZ300) Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 39
Page 3 and 4: Tiger 320 Series Modular Literature
Page 6 and 7: Planning to Harness the Power of Ti
Page 8 and 9: SP1 SP2 SP3 SP4 SP5 SP6Planning to
Page 10 and 11: Configuration Utility ProgramThe Ea
Page 12 and 13: Index32-Bit Operating System ......
Page 14 and 15: Controls and IndicatorsFront Panel
Page 16 and 17: SP1 SP2 SP3 SP4 SP5 SP6Front Panel
Page 18 and 19: Front Panel Programming Codes conti
Page 20 and 21: Initial Setup Procedures continuedI
Page 22 and 23: [CAL] - Calibration Modes for Input
Page 24 and 25: [CAL] - Calibration Modes for Input
Page 26 and 27: Initial Setup Procedures[CodE_1] -
Page 40 and 41: Setpoint Programming Mode continued
Page 42 and 43: Setpoint Programming Mode continued
Page 44 and 45: Registers That Can Be Selected By F
Page 46 and 47: Carrier Board Output PinsAnalog Out
Page 48 and 49: 2V20V200VCUSTOMVOFFONON1 2Component
Page 50 and 51: +++0_+0_I-Series Input Signal Condi
Page 52 and 53: ++ONONONI-Series Input Signal Condi
Page 54 and 55: +V++++++++I-Series Input Signal Con
Page 56 and 57: Texmate, Inc. Tel. (760) 598-9899
Page 58 and 59: Ordering Information continued80-MO
Page 60: Case DimensionsPANEL CUTOUTCase wil

DI-50E Data Sheet - K - Tech, Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?