DI-50E Data Sheet - K - Tech, Inc.

More documents

Recommendations

Info

SP1 SP2 SP3 SP4 SP5 SP6Front Panel Push Button Configuration and Setup for Programming ConventionsThe meter uses a set of intuitivesoftware codes to allow maximumuser flexibility while maintaining aneasy programming process. Toconfigure the meter’s programmingcodes, the meter uses the threeright-hand side display digits.These are known as the first, second,and third digits and can beseen in the diagram opposite.To explain software programming procedures, diagrams are usedto visually describe the programming steps. The following conventionsare used throughout the range of Tiger 320 Series documentdiagrams to represent the buttons and indicators on the meter, andthe actions involved in programming the meter:Prog.SymbolOperational DisplayProg.ExplanationOperational DisplayFirstDigitSP1 SP2 SP3 SP4 SP5 SP6SecondDigitThirdDigitThis symbol represents the OPERATIONALDISPLAY. After the meter has been poweredup, the display settles and indicates the calibratedinput signal. This is known as the operationalmode and is generally referred to as theoperational display throughout thedocumentation.Programming procedures are graphic based with little descriptivetext.Each procedure shows a number of meter panel displays runningin procedural steps from the top to the bottom of the page.If need be, the procedure may run into two columns with the leftcolumn running down the page and continuing at the top of theright-hand column. Each action performed by the user is shown asa numbered step.Each procedural step shows the meter display as it looks before anaction is performed.The hand or hands in the procedural step indicatethe action to be performed and also how many times, or forhow long, the button is to be pressed.For example, the diagram below shows the meter in the operationaldisplay. With a left hand pressing the P button and a righthand pressing the button, the user is entering the main programmingmode. This is indicated by the next diagram displaying[bri] and [5].This is the display brightness mode and is the first submenuof the main programming mode.Step 1Pressat sametimeOperational DisplayProg. SP1 SP2 SP3 SP4 SP5 SP6Pressat sametimeAll programming modes are entered from this level.PPress2[Span][10000]This symbol represents the PROGRAM button.In a procedure, pressing the program button isalways indicated by a left hand. A number indicateshow many times it must be pressed andreleased, or for how long it must be pressedbefore releasing.Prog. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6Press4 secsOperational DisplayProg. SP1 SP2 SP3 SP4 SP5 SP6This symbol represents the UP button.Shown in a diagram, pressing the UP button isalways indicated by a right hand.This symbol represents the DOWN button.Shown in a diagram, pressing the DOWN buttonis always indicated by a right hand.Where two right hands are shown on the samediagram with the word OR between them, thisindicates that both the and buttons canbe used to adjust the display: UP for increase,DOWN for decrease.Text or numbers shown between square bracketsin a description or procedure indicate the programmingcode name of the function or the valuedisplayed on the meter display.Where a left and right hand are shown on separate buttons onthe same diagram, this indicates that the buttons must bepressed at the same time.The exceptions to this rule are when carrying out the Model andSoftware Code Version Check, or the Code Blanking and MacroCheck.Prog. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6XXProg. SP1 SP2 SP3 SP4 SP5 SP6Step 2ORPress2Prog. SP1 SP2 SP3 SP4 SP5 SP6Prog. SP1 SP2 SP3 SP4 SP5 SP6When two displays are showntogether as black on grey, thisindicates that the display is toggling(flashing) between thename of the function and thevalue or configuration setting.Where a number is not definable,the default setting [000] isshown.If an X appears in the description of a 3-digitprogramming code or in a configuration procedure,this means that any number displayedin that digit is not relevant to the functionbeing explained, or more than one choicecan be made.Page 16Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com21 June, 2004 DI-50 320 Series (NZ300)
Front Panel Programming CodesThe meter’s manual programming codes are divided into twomodes: the main programming mode, and the setpoint programmingmode (See diagram below).Each mode is accessible from the operational display.Main Programming ModeThe main programming mode provides access to program allmeter functions, except setpoints.Operational DisplayProgramming TipThe easiest and fastest way to configure theTiger 320 is to use a PC with the free downloadableconfiguration utility program. (see page 10)Setpoint Programming ModeThe setpoint programming mode provides access to programall setpoint and relay functions.To enter or exit the MainProgramming Mode, pressP and at the same timeMain Programming ModeProg.SP1 SP2 SP3 SP4 SP5 SP6To enter or exit the SetpointProgramming Mode, press P andat the same timeSetpoint Programming Mode[bri]P[CAL]P[Cod_1]P[Cod_2]P[Cod_3]P[Cod_4]P[Cod_5]P[Cod_6]P[Cod_7]P[Cod_8]P[Cod_9]Display BrightnessCalibration Modes for Input and OutputCode 1 – Display ConfigurationCode 2 – CH1 Measurement Task & Sampling RateCode 3 – CH1 Post Processing & Serial Mode FunctionsCode 4 – CH2 Measurement Task & Sampling RateCode 5 – CH3 FunctionsCode 6 – CH4 FunctionsCode 7 – Result ProcessingCode 8 – Data Logging & Print ModeCode 9 – Functions for Digital Input PinsProgramming TipSave Code Settings & ExitTo save a new main programmingmode configurationsetting and return tothe operational display atany point, press the Pbutton once.Then press the P andbutton at the same time toexit.Programming TipSave SP Settings & ExitTo save a new setpointconfiguration setting andreturn to the operationaldisplay at any point,press the P buttononce.Then press the P andbutton at the sametime to exit.Setpoint Activation ValuesEnter these menus to adjustSP activation values[SP_1]P[SP_2]P[SP_3]P[SP_4]P[SP_5]P[SP_6][SPC_1]Setpoint 1Setpoint 2Setpoint 3Setpoint 4Setpoint 5Setpoint 6Setpoint & Relay Control Function SettingsPEnter these menus to configureSP control values[SPC_2]P[SPC_3]P[SPC_4]P[SPC_5]PSetpoint 1Setpoint 2Setpoint 3Setpoint 4Setpoint 5The Setpoint andRelay ControlSettings diagramon Pages 42 and43 shows thethree digit configurationsettingsthat are appliedindividually toeach setpoint.See Page 41 for anexample procedureto configure asetpoint for simplerelay functions.P[SPC_6]Setpoint 6[Cod10]PCode 10 – Bargraph SetupCode 10 applies to Tiger 320 Series meters with bargraph displaysonly. See user manuals for DI-50B51, FI-B101D50, andGI-50B101.POperational DisplayProg.SP1 SP2 SP3 SP4 SP5 SP621 June, 2004 DI-50 320 Series (NZ300) Texmate, Inc. Tel. (760) 598-9899 • www.texmate.comPage 17
Page 3 and 4: Tiger 320 Series Modular Literature
Page 6 and 7: Planning to Harness the Power of Ti
Page 8 and 9: SP1 SP2 SP3 SP4 SP5 SP6Planning to
Page 10 and 11: Configuration Utility ProgramThe Ea
Page 12 and 13: Index32-Bit Operating System ......
Page 14 and 15: Controls and IndicatorsFront Panel
Page 18 and 19: Front Panel Programming Codes conti
Page 20 and 21: Initial Setup Procedures continuedI
Page 22 and 23: [CAL] - Calibration Modes for Input
Page 24 and 25: [CAL] - Calibration Modes for Input
Page 26 and 27: Initial Setup Procedures[CodE_1] -
Page 38 and 39: SP1 SP2 SP3 SP4 SP5 SP6SP1 SP2 SP3
Page 40 and 41: Setpoint Programming Mode continued
Page 42 and 43: Setpoint Programming Mode continued
Page 44 and 45: Registers That Can Be Selected By F
Page 46 and 47: Carrier Board Output PinsAnalog Out
Page 48 and 49: 2V20V200VCUSTOMVOFFONON1 2Component
Page 50 and 51: +++0_+0_I-Series Input Signal Condi
Page 52 and 53: ++ONONONI-Series Input Signal Condi
Page 54 and 55: +V++++++++I-Series Input Signal Con
Page 56 and 57: Texmate, Inc. Tel. (760) 598-9899
Page 58 and 59: Ordering Information continued80-MO
Page 60: Case DimensionsPANEL CUTOUTCase wil

DI-50E Data Sheet - K - Tech, Inc.

Create successful ePaper yourself

Delete template?

Save as template?